Wireless :: Browser Cannot Connect To Server In New Tab
Jan 25, 2012
I have the wireless connection working and when I try to browse information on the any browser like Firefox, Internet Explorer, Chrome, Opera and all but it cannot connect.It display a message saying "Connection closed by the remote server" in Opera and in other browser it doesn't display anything even after several times of refresh.I also tried restarting the system and it connect the home page of the browser and when I open the link in new tab it doesn't go to that link.
Not sure how I got here, but I cannot now connect to the E3000 using the Browser Utility. USing https://10.x.x.x, shows certificate warning page, then when I continue "Internet Explorer cannot display the webpage".DId NOT change the host hame.Last time I used the Browser Utility (weeks ago) was to disable the wireless to check something. Reenabled the wireless, no apparent problems until today when I tried to access via the Browser Utility.As I never ran Connect, there are no settings to change, and now it cannot detect the device.I guess I'll wait until I HAVE to change something, and do a 30-30-30 reset.
I am tryign to set up an Aironet 1142, I have created a reserrvation in DHCP using the MAC address, and the reservation shows as active, but I cannot connect to the device with my browser.
i have a linux server PC and its containing videos, tutorials etc. but my Question how can i play that video files in my browser like you tube??? now its working like non-streaming, jus download and play through any player like!!but my purpose is play videos throgh firefox browser..
Earlier today I was attempting to do something with my router settings and ended up reading on the internet that I needed to do a hard reset to access my router interface - when I typed in the IP address, it came to a "could not find server" error in the browser. After doing the hard reset (holding down the reset button for 30 seconds) I was able to access the router, and adjust the settings. After doing this though I was no longer able to connect to the internet through the router, although the router is sending out a signal (it says connected to linksys but "no internet connection"). I am currently connected directly to the modem right now using my laptop.
TL;DR: Did a hard reset on my router, now it's sending out a signal, but no internet. Modem still has internet, as does the router, (the internet button is green).
Not too much networking savvy - but here goes. Want to use router as local lan - no wireless. When router is connected to laptop via RJ45 I loose my ability to connect to sites via browser. IPconfig shows wireless adapter at 192.168.1.3. When router is attached it's ip is 192.168.1.1. Disabled the wireless in the settings but no dice. When the router was used with DSL it was set at PPPoE but now that I'm just using it locally not sure whether it should be DHCP or Static or other.
I just purchased a E4200 and I have some questions;
1. I have the hardware version 1, and I noticed the hardware version 2 has a newer version of Cisco Connect. Can I use the newer version of Cisco Connect on my E4200 V1?
2. Is there a way to hide passwords in Cisco Connect and in the browser UI for the router?
3. Is there a way to have a separate admin password and wireless password?
I also have a issue, I want the browser web UI to display in english, but it insists on changing it back to my native language from time to time.
I accidentally deleted my wireless adapter, so i re installed it in device manager, and now i can't connect to anything except my router, when i check internet options, it tells me that i'm connected to the internet. I can go on the internet on this other laptop and desktop computers, xbox and whatever else, just not the other laptop (it's an hp pavillion dv6000 btw)
I am experiencing the same problems except different setup. I use avg and spybot as my security.The problem is that I cannot use any browser be it firefox or chrome or IE. I can't even update my avg or spybot. I can type in my router and get that. I have a laptop, which I am using now, that is working fine with the internet. Even my 360 is able to connect so I can watch netflix.I have "flushed" the connection, I have used winsock, and macshift. I'm running AVG and Spybot with spybot coming back clean but I have a gut feeling it won't work.I have run sfc /scannow and there is some files missing. I inserted my original disk into the cd-rom and refuses to detect the cd after so many tries. I reset the router and computer several times. I tried running sfc /scannow in safe mode but didn't run[CODE]
I cannot get XP pro to connect to internet with any browser. It sees all of the other computers on the network and can ping any of the connection, including the router, but will not bring up any web pages.
New windows 8 pc which can't connect to an internal ip (inside address 192.168.1.237) through browser, either firefox or IE. I use this address to open a webdav session on browser to transfer files form pc to iphone, or vice versa, using ipphoone app Files Pro. I have no problem connecting on this using my old windows xp pc using ie, which is in another room. Both pcs used my fairly new ASUS ac router. Is there a windows8 firewall or toehr exception list that I need to modify on the windows 8 (HP) laptop?
I have 2 PC's on a LAN, both Windows 7 Ultimate. Both PC's is connected to the same router via ethernet.Now PC number two has internet access and works great, but PC number 1 also shows "Internet Access" in the system tray and also in the network map, it shows that it is connected to the internet. But when I open ANY browser(FF, IE, Chrome) it cannot connect to the internet. Skype also cannot connect. As I said, the other PC (PC2) can connect fine and has the exact same setup as PC1. However, on PC1, when I manually connect via a dial-up broadband connection using the SAME username and password to my ISP as I used in the router config, it connects. The problem is that it loses the connection every 2 minutes or so...(failed to connect...redialing...). What I can do on PC1 to make it connect to the internet via the router the same way the other PC does?
Also, the two PC connects fine over the LAN between each other, but as I said, PC 1 cannot connect to the WAN the same way PC2 does. Things I tried: I did a TCP/IP stack repair and rebooted. Nothing. I disconnected the 'working PC' from the LAN, nothing. I uninstalled the Antivirus and Firewall, nothing...
Router: Siemens Giga 762SX
Network adapter on PC1: Realtek RTL8139/810x Family Fast Ethernet NIC. I do have the latest drivers installed
I am in kuwait and I have a CCTV camera in Philippines. It is setup with IP 112.200.216.88:3130. I can ping it but I am unable to connect through browser. I am working behind a router. Anything I need to do on my network in Kuwait to be able to connect to it?
I recently am trying to get an open nat type so I can play Playstation network better. I watched a video and they told me to turn off the NAT and I did now it does not let me connect to the router page now, I can connect to the internet and stuff but I can't connect to the router page
I just got myself a Cisco RV220W, connected my laptop to configure it. I receive an IP adress by DHCP (192.168.1.x) and can ping the router (192.168.1.1). However, when I try to connect to the router by the web interface, I receive this message in my browser (Chrome):
The webpage at https://192.168.1.1/ might be temporarily down or it may have moved permanently to a new web address. Error 113 (net::ERR_SSL_VERSION_OR_CIPHER_MISMATCH): Unknown error.
In FireFox: Secure Connection Failed An error occurred during a connection to 192.168.1.1. Cannot communicate securely with peer: no common encryption algorithm(s). (Error code: ssl_error_no_cypher_overlap)
In IE9: I get no error message, the page never loads
Is it DoA or how to get connected to the web interface?
The Lg840g is a tracfone with wifi capability. I get strong wifi signal and connection at home, but receive failure to connect to requested host message when I open the browser. This phone works at wayport wifi, so I assume it's a compatibility problem with the router. Is there a fix? (Router works great with our Acer and Kindle tablets though.)
The wireless in our condo requires a user and password to be submitted via a browser to connect to the network. My bluray player does not give this option or have the ability. Is there a way to accomplish this? Is there a bridge or router that can make the authentication to the wireless in the building that I could then connect the blu ray to?
I have install the administration toolpack on Windows 7 and enabled remote connections on my server 2008 box, When i try and connect with my Windows 7 server manager it does not work.I see stuff on google about enabling a trustedhost with winrm but can't find a way to do this.
Browsers will not download certain files. They often get stuck at 300-400 kb, but some other files are ok. Eg. I can never download Java 64 from filehippo, whereas CCleaner is good to go from filehippo.WirelessTried with no firewall, no antivirusprogram.My other computer wireless downloads.Tried different drivers to network adapter.
Out of the blue my wireless connection stopped working, my browser cannot connect, I don't know what to do. I have a Samsung laptop that's running on Windows 7. I thought it was the browser so I installed the Internet Explorer 9 and while doing so it was able to download the updates but when I open up the browser it still doesn't work.
I'm thinking that it might be a network problem but I've ran out of ideas. I have a netgear router that's connecting a desktop computer, two VOIP devices, my sisters Mac works but we have two laptop that aren't working. I've also tried connecting it directly to an ethernet cable from the router but it's still not able to open the browser.
I can't access the router through the IP within the browser. It's an older WRT54G. I've never used the downloaded software that allows you to connect to it, but that's what I was going to try.
Before the latest update and with the latest update, after about one week, I cannot access the router wirelessly using 192.168.1.1. Using IE 10, Chrome, and FireFox all give me no response. I type in the address and the web page never changes. It keeps me at the home page of my browser. I do not get any errors or messages.
Also I tried to use the DHCP Reservation page, and the names of the devices will not allow spaces or any special characters. Sure would be nice to allow such.
I just noticed that my router reverted back to 1.1.28.146856. I have updated twice via the web browser to version 1.1.28.147876 and once via direct connection and the downloaded file, but the router keeps reverting back to the older firmware.
I have a wireless controller 2100. I can't access it via browser, when I am connected to one of its physical ports. I use the same subnet ip address as that of the management interface of the wlc.
After getting New Workstations, I wanted to connect that to the SERVER but Windows 7 could not log into domain of our server with Windows Server 2003. Besides following the proper process/steps. I am able to use the printer and internet shared through SERVER though.
I am using a old notebook (2 years old) with windows server 2008 on it. I needed to remove al the drivers, because windows server 2008 isn't using the drivers of windows xp, and it wanted a clean installation.
Now the question and problem, is it possible to let my server wireless connect to my home network?
I am using for a server my old notebook: Acer Aspire 5738ZG 2GB RAM, Intel Pentium dual-core processor T4200 Nvidia GeForce G105M 512MB (doesn't matter) Atheros AR5B91 Wireless Network Adapter
I already installed the driver for the Wireless network adapter. Windows can't find any networks, when i try to connect.
I have installed my E3200 downstream from the Verizon FiOS Actiontec (going the other way disables FiOS functions). 1. My browser can get to the E3200 (192.168.1.2) when connected via wireless, but not when connected via ethernet cable. 2. When going to connect wirelessly, the 2GHz connection is visible but the 5 GHz connection is not (I have them named differently). How do I see both wireless connections?
When I try to access the browser based utility through the address bar, I don't have the username or password.....tried admin for both and for just the pw. When I try to access advanced settings through Cisco Connects router settings / advanced settings, it comes up as if many objects were unable to load. Linksys E2500.
I am unable to access my router through the ip address (192.168.1.1) even though I have verified that is the address. To be sure, I did an ipconfig release/renew, but no results. I want to limit a user's network access by MAC address and I don't think I can do that without accessing the router thru the ip address.
My Motorola 850G router is several years old and working fine. However, my wi-fi connection is presently "unsecured" and I need some assistance as to how to go about setting up a secure network. My browser is not recognizing the router's default IP address.
