ive recently bought a tcl internet enabled tv. I have tried connecting it to the wireless network and it keeps giving me an error that the "connection failed due to timeout".
View 5 RepliesI have a laptop that is running windows 7 premium and a desk top that is running xp pro. The laptop is connected to the internet but the desktop is not. I have them set up in a ethernet network through an RJ-45, and both are connected, but I can't seem to share the laptop's internet connection with the desk top. I've enabled internet sharing with the wireless network, but my desktop still cannot connect.
View 1 Replies View RelatedI have windows 7 PC. On the normal bases it has 3 internet connections 2 wireless and 1 hardwired. The 2 wireless are used for internet access and the hardwired is for my LAN through my router. The wireless connections are throught ATT mobile devices. I use my lan to share files through PC in my household and it has no internet access. The problem is that whenever I have all 3 of these connections connected windows always sees the hardwire connection as internet access so I can't use the internet even if my 2 other wireless connections are enabled. However, If I disable the Local area network connections and the leave 2 wireless connections enabled I have internet again.is there a way to just make windows use the hardwired connection as local and use the wireless connections for internet?
View 1 Replies View RelatedMy Toshiba laptop running Vista as an operating connects just fine to the wireless network at my house. However, I will soon be house-sitting at a house that also has security-enabled wireless available. I connect just fine at my house, but whenever I put in the password at their house it says that that it cannot connect because of a timeout. I can't figure out what the problem is, because I recently went to the public library that has wifi and got on just fine. why in the world it will not connect to this specific wireless router??
View 7 Replies View Relatedam trying to connect my laptop withgalax tab via mobile AP configuration, it give me this error {dhcp is not enabled for wireless network connection}
View 1 Replies View RelatedMy wife and I Security Enabled our wireless network several months ago.We recently moved, and after transferring Internet service, we realized we'd lost our passkey.My wife's laptop has, after one failed attempt to connect to the network, refused to even show the network as an available connection.We currently have the router set to broadcast SSID.We have restored factory settings on the router and completely revamped the security setup.We've removed all other networks in the area as optional connections on her computer.We also replaced the ethernet cord to my desktop because the old one started erratically disconnecting.Nothing's worked.My wife's computer is a Dell laptop using Windows Vista.
View 6 Replies View RelatedI recently entered the realm of wireless networking for my desktops and was able to connect my personal desktop successfully. Unfortunately, the other desktop I really need to make wireless is having difficulties. The computer never shows the message that a new device is discovered/installed. The adapter shows up under hardware devices and functioning properly but this is not the case. I installed the driver from the included CD but when I use Windows to troubleshoot, it says that the driver and adapter aren't working. When trying to set up a new network, I get a grayed-out wireless icon in the system tray and can't proceed. I disabled the firewall and antivirus so I could start over, uninstalling the driver, restarting and installing again.
View 12 Replies View RelatedEver since I bought the E4200 months ago I had no wireless network between my laptops. pc's devices. I discovered now that I do have network (everything cool) when I disable NAT. That is all nice, but I don't have internet then.
View 8 Replies View RelatedFlex 7500
Software Version: 7.2.103.0
I have a Flex 7500 with 200 1142AP's working fine in remote office and local setup. We have since purchased 3 OEAP 602's and looking to distribute to teleworkers.
I have configured the OEAP to point to the NAT'd IP of the WLC, the OEAP does connect and is listed briefly in the WLC wireless listing but I am not able to make any configuration changes, it will then dissassociate and try the join process all over again. I have attached below the OEAP 600 event log. I see that the WLC does not support data DTLS encryption and looking to make this work.
I have tried to install the DTLS license file from the Cisco website, but says license failed to install, with no other errors.
*Jun 18 15:18:43.938: Build version 7.0.112.72 (compiled Feb 3 2012 at 01:56:39, [L]).
*Jun 18 15:18:47.859: CAPWAP State: Init.
*Jun 18 15:18:47.860: CAPWAP State: Discovery.
[Code]....
Ok, so I recently upgraded to a Linksys E3200. I am trying to get the QoS to work properly. I know that it is supposed to prioritize network traffic, so that if I have busy traffic but I am playing an online game, it should keep my gaming from stuttering while slowing other traffic down.
The problem is that every time I enable QoS everything slows down dramatically. I had a 200MB download that was going to take 5hrs with QoS enabled, that took 10min with QoS disabled. And with QoS enabled I can't even watch a youtube video without it pausing to buffer every 10 seconds. And that was the only PC/device using the network at the time. Again turning off the QoS WMM option solved the problem. I have noticed this problem with multiple routers and brands and usually just disable QoS as soon as I set up a router, however I heard that I won't get the full benefit of 300Mbps without QoS enabled.
I don't have any special Voice over IP needs, or video streaming etc. and I rarely am using multiple network devices at the same time. Is there really any reason I should enable QoS? Also I never really play with the settings for QoS, I just figure that since it comes enabled by default it should work for the average consumer.
I purchased a Linksys EA3500 about two months ago, brought it home and set it up with my DSL provider and everything was great, until sometime last week, and since then my download speeds have just plummeted to basically nothing. I did some troubleshooting but I cannot seem to find what the issue is. I have checked all the cables etc, and I know that it is definitely something with the router itself..My current Speedtest.net speeds are as follows (I am paying for a 5mb connection) with the EA3500.Ping of 15ms Download speed of .67mbps, Upload speed of .60mbps.When I remove the router and hook straight to the DSL modem I get the following results.Pink of 12ms Download speed of 4.89mbps, Upload speed of .60mbps
- I have tried to reset the router both by holding the reset button and through the configuration application.
- I have enabled and disabled wireless to see if that was slowing things down
- I have plugged in my old WRT54G and I get the 12ms, 4.89mbps,.60mbps results on it (so I know its the EA3500)
- I tried putting the computer in the DMZ
- I have changed the ports that the computer is plugged into
- I have disabled and enabled IPV6 on both router and network card
- Firmware version - 1.1.38.134141
I have both the WRT54G and a E1000 wireless routers and this problem is occurring for both of them.I use AT&T DSL and the speeds are fine when it is :
1. Not plugged into router
2. Wireless Network Mode is disabled through the router configuration page, having all devices wired.
However when wireless network mode is enabled, speeds drop significantly, 15~17 ms ping goes to 250~800 ping, and download speeds are way lower also. When the router is reset, the regular speeds will return for maybe 30 seconds to 1 minute, then it'll drop back down. I'm positive there's no outsiders connected to my network and this problem still occurs, only when the router is giving out wireless signals. Sometimes the problem randomly goes away for a while but it will always come back. I've tried many things, firmware upgrades, factory restore, none of them seem to work, the only solution so far has been to disabling it, but I need it to be on as there are other devices in other rooms of the house that need WiFi to connect to the internet.
E3200 works great until I enable QoS. The device uses QoS and works find until reboot. If QoS is enabled and the device is rebooted, its stops routing from LAN side to Internet side. Administration-->Diagnostics allow me to ping/trace route to Internet sites and local LAN clients but cannot reach Internet from local LAN.
Windows networking icon indicates "No Internet access". I can ping other devices on local LAN.
Disabling QoS restores routing and you can re-enable QoS after that and all is well. Unfortunately, if there is a power failure when I', not there to disable/re-enable QoS afterward, other household members can't use the Internet till I get home.
Wondering if any other QoS users have observed the same problem.
I am using my neighbor's WiFi connection in my WiFi enabled motherboard PC with good signal strength. Now i want to connect a router to my PC so that i can easily use WiFi for my mobiles.
View 4 Replies View RelatedI have just bought a Wansview NC541W IP Camera to monitor my home while I am at work (my home was burgled recently) and I have no idea how to connect it to my broadband router wirelessly. I went onto the network settings of the Camera and set up the wireless setting to connect to my router network (typed in the SSID and wireless pass key etc) but nothings happening?!? I can connect the two devices with an Ethernet cable and have the camera working perfectly, but can't do it wirelessly!
View 1 Replies View RelatedI have disabled / enabled and unistalled / installed and updated driver software but to no avail.It has been replaced, I have refreshed TCP/IP as per previous instruction found here and it did go a bit further, but now stuck as per below from CCX diagnostics Utility:
[code]...
I have a HP G62 laptop with windows 7 and a Atheros AR9285 wifi adapter. The Wireless Assistant shows the WLAN as disabled. In the device manager, the adapter is listed as enabled. When I push the F12 key that turns on and off the wireless, the wireless assistant alternates between showing the WLAN as Off or Disabled. I tried disabling the adapter and re-enabling it from the device manager, but the wireless assistant still shows it as disabled.
View 3 Replies View RelatedI had it working fine up until i decided to install a new harddrive on my xp pro machine. but to the point, when i connect to the 3g card its fine, but if i try to enable the lan at the same time it disconnects my 3g card. my problem isnt how to network two computers, its how to get lan and a usb modem working simultaneously. i have tried to enable ics, then reboot. same results. if i can get the lan to stay on while the 3g card is on i have the rest whooped.it is some kind of setting somewhere. maybe i need to install windows 2003 server or something like that.
View 9 Replies View RelatedWell i am currently using a BSNL DNA A211-1 wifi modem-cum-router with a wireline inbetween my PC (win7 ultm) & the router, so as to connect to the internet. i use the wifi feature of my router to connect my samsung gts5570 wifi enabled phone as well as a few other wifi enabled devices, to use internet on them. now i was thinking whether i can connect my desktop pc to my mobile phone using this wifi router somehow? how can that be done since there is already 2 different network that exist between my pc & router thru wireline & my mobile & the router thru wifi, all i need is a way to sync these to networks into one, so that my pc & my mobile use internet & at the same time they connect to each other as well.
View 3 Replies View RelatedAt home, I have 2 laptops and 1 smartphones, I set up a wi-fi network with WEP (WPA2) key. Since then the Windows Wireless manger is not able to connect.
If I remove the WEP key, I am able to connect.
The Internet connection is good. I am able to connect a HP, a Lenevo laptop, an iPhone with the same WEP key - but Dell does not connect.
I am running Windows XP on Latitude E6410 with Intel i5 Core.
I am trying to connect to a Security-enabled wireless netowork. I have the key. My problem is that I can't seem to figure out how to enter it. When I try to connect I open the "view available networks"window. I see the network name and it shows a strong signal (all 5 green bars).
View 3 Replies View RelatedI try to setup a network where both interfaces in my laptop are enabled. One is a wifi interface, the other is LAN. My WIFI is supposed to connect to a router that connects to a modem and the LAN interface is supposed to connect to my other PC.The problem with the configuration occurs when I try to access the internet, my laptop confuses not knowing where it should send the IP packets to the LAN or to the WIFI interface.What is the best solution for accessing the internet from my laptop (I don't care about accessing it from other PC) without change the topology? Should I configure the browser in my laptop so that it access internet through proxy?
View 2 Replies View RelatedI have a branch office connected to the Head Office through a VPN Tunnel in cisco 1841 Router. If i enable Internet for any pc in Branch Office through cisco router i cannot access it remotely from Head Office. [code]
View 2 Replies View Relatedi have come across this solution to dual internet connections, c2950-i6k2l2q4-mz.121-22.EA14.bin is the IOS and the router is a 2950 Dual Wan model. I don't know alot about this stuff I'll admit, but it is on the default configuration with IP 192.168.27.7 255.255.255.0, gateway at 192.168.27.8. The hostname below is something I don't know exactly what it means but my guess is its the line at the command prompt with the name.
It has VLAN1 with fa0/1-24, gi0/1 - 2.
This is the script but I don't know why its not taking the commands as at ip sla monitor 1 I get invalid command error. What do the ! mean are they comments and not entered?
I am running a Netgear wireless N-300 router from my RoadRunner modem. I installed the network early last week to no problems. A few days ago the wireless devices wouldn't connect. They recognize the network, but will not connect to the internet. I have given them their own IPs with the router, and shut off DHCP...this didn't work. I've obviously tried to power cycle the router and modem....this didn't work. I can't seem to find a fix. My android devices connect to the network just fine, but otherwise if it isn't connected via wire, it won't work. I've also tried to connect things without the android devices connected just in case it was interference, and that didn't work.
View 2 Replies View RelatedMy lan ip is 192.168.1.10 an wireless is automatic plssend me the settings to get both together
View 1 Replies View Relatedi use cisco vpn client software to connect my laptop to my company's network when i at home. using dsl modem.
i wonder if it is technically possible to connect my local printer to dsl router and in such a way establish connection between my laptop and printer?
i just hooked up a dlink router at home so i can use my laptop in different rooms. i have a desktop in one room and the internet works fine but when i hooked up the wireless router i can connect to the network but it says no internet access so i cannot get online my brother in law is really good with computers and i called him and tryed doing a bunch of different things like changing the web address and such but nothing will work.
View 4 Replies View RelatedThe problem is I can't connect to my router, It says "unable to connect to wireless network" . Been trying to 5 days now to fix this, Not getting anywhere.Laptop is, HP Pavilion g6 Notebook, My network wireless adaptor is realtek rtl8188ce 802.11b/g/n.
OS Version: Microsoft Windows 7 Home Premium , Service Pack 1, 64 bit
Processor: Pentium(R) CPU B950 @ 2.10GHz
RAM: 4.00GB
Graphics Card: Mobile Intel(R) HD Graphics Family
The only thing that will connect to my wireless network is internet explorer. I have tried Firefox and other programs I have that require internet and they will not connect.
View 1 Replies View RelatedI have a home ADSL2 Modem Router. I have 3 computers connected to this wireless network and also with Internet access. However, I have 1 notebook connected to the wireless network but saying No Internet access.
View 13 Replies View RelatedI have two separate wireless networks in my house, one of them is for sharing my NAS data and the other is for Internet.problem is when I connect to the NAS network and after that I change my network to the other network, I can not connect to the internet ( I can connect to the wireless).
Just after restarting I can see the Internet
I have upgraded to the new RV042G to take advantage of the gigabit Ethernet speeds and to prepare for when our ISP upgrades our bandwidth. I currently use the RV042 with Protect Link enabled to filter out various categories from our network traffic. I noticed that this feature is not included with the RV042G.
Is this something Cisco will decide to add back in later? In the meantime, how to block content on the network? The basic URL and keyword filter will not meet our needs, since it is much easier to let a service such as Trend Micro manage what is blocked in the categories they offer.