i new in this forum,i just want to know it that possible we can configure the normal wireless modem?.From my knowledge we can configure manually for cisco router or switch at pc by doing on hyper terminal. It that normal wireless modem can be configure using hyper terminal?.
Recently I had changed my ISP and I get a brand new modem and a D-Link DIR-615 wireless router, but the problem is the wireless signal is not strong enough to reach second floor, so I decided to get a new TP-Link TL-WA901ND access point and after configure the AP to repeaters mode, I saw it has traffic coming throughout to the AP but my PC cannot get any internet connection not even an IP address. When I was facing this problem, I thinking of is that possible using my old wireless router which is TP-Link TL-WR841ND to have a internet connection working with D-Link wireless router, I had tried plug my TP-Link router LAN port to D-Link router LAN port with a network cable and setting into same IP range (192.169.0.xx) but cannot get any traffic getting through.
I have WRTG54G with 4ports and a internet port, i have a zoom adsl modemfor DSL i wants to share DSL connection with internet port on WRTG54G but i d'nt know how to do this
I have rather huge connection at home. DL speed 80Mb, UL speed 3Mb.When I connect my PC directly to modem and configure PPPoE connection, I get 81Mbits/sec. When I connect my old ASMAX $30 router, I get 78 Mbit/sek. And I find it OK.But when I connect my EA6500 I get 28 MBits/sec. Same result on wire as on wireless connection. Of course If I enable prioritisation, I get even less, 12-15 Mbits/sec.I tried already even configuration with ASMAX as wired router and EA6500 connected to its LAN port. It gives me 50Mbits/sec.
Is it normal for an E1000's LEDs to get dim after a few years??Because my LAN port #1 and #2 are dim, as well as the power LED.I'm guessing it's just because they are always on?
just installed 6 new APs to a client remote site off a 5508 controller. 5508 is running 7.0.116 total of 78 installed APs, mostly 1142's with a dozen or so1242s. All going perfectly until I was about to leave site and noticed two of the APs had no LEDs lit. Checked in the controller, as I had renamed them so knew they were on the system, and they are both there. Connected to each of them and was successful and everything seemed ok - no blue LED though. Rebooted them and the LEDs work as expected during the boot process but as soon as they have entered normal operation the LEDs go dark. urls....but no reports of it with anything other than 3502's.Change process is galacial and heavily monitored so dont want to invoke it if it wont address the concern.
I have an odd problem with the FTP server. I currently hooked up a 250GB portable HDD which is formatted in NTFS. A single folder in the root of the drive is mounted as the FTP server. Every time I upload a zip or far, the file comes out ends up being uploaded corrupt and double the original file size. I have used 2 FTP clients, using either ASCII or binary. No matter how I go about it, I can't make the files upload at the normal file size. Its not just archives, however, I tried an mp3 and it too got uploaded corrupt and double the size. I then downloaded the mp3 to try and play it but it didn't play in windows media player. However I loaded the 'corrupt mp3 into audacity and the file played like normal.
I accidently went into bridge mode on my linksys E2500 router. I want to reset it back to normal but i'm not sure how to do it. i tried the little reset button on the router but that didn't change it.
I have installed an Aironet 1130AG and utilized a power injector for the power source. I have the settings configured correctly in IOS, but the AP takes about 7 minutes to come on (illuminate LED status lights) once the Ethernet cable is connected. Is this 7 minute power-on delay normal when using POE? I am used to the instanteous "on" that usually comes with Cisco products being connected directly to the AC adapter.
I brought a LAP1131AG, only later found out that it can only be used with a controller.Is there any way I could change the firmware to make it a normall Access Point?
I have a laptop (let me call it A) with Intel Centrino 1030-N wireless (iwlwifi module), running Arch Linux, and another laptop (I will call it B) with Atheros AR928X wireless (ath9k module), running Ubuntu 11.10. They connect to a wireless network provided by a D-Link DI-524 router (802.11g), which in turn connects to a DSL modem (10Mbps/1Mbps link)
Copying files between those machines, either through scp or mounting a share via NFS or Samba, is very slow (at most 200 KB/s) and sometimes fails (times out), even when both machines are inches away from the router. However, downloading files on either machine works correctly at the expected speeds (~1.2 MB/s).
I ran iperf, as recommended in a comment, and it gave me this: [code] The bandwidth is very low, as can be seen from those results.
I have WAG120N and is working fine, but has very poor wifi range. I recently purchased EA 6500. how to setup my WAG120N as a modem only and shift all routing to the EA6500
I found out that I cant access my modem (TP-Link W8901G) config page at 192.168.1.1. I was pretty sure my ID and password is correct since I never changed them. It is also unlikely that the password got changed by other people who are stealing my Wi-Fi as I turned my WLAN on only when I requires the connection then it get turned off afterwards.
have wireless d-link adsl modem router which usually use for adsl connection sharing, but i have a cable internet connection, so my question is can i share my cable internet connection with this router?
I just ordered the Linksys WAG120N modem/ router and need configuring the same on the BSNL network. Any Document or link about his Installation and configuration.
I have a Pix 501 running 6.3 code sitting behind a cable modem. I use ip address outside dhcp setroute because I don't have a dedicated IP from my cable provider.
How do I configure the Pix to host VPN connections from my iPad when offsite? Since the outside interface is going to change, I can't configure a static IP.
Is it normal for the "CISCO" icon/light to "fast flashing" periodically - not to be confused with the "slow flashing" that the E4200V2 displays when being "power cycled"?
Is it possible to configure a Westell 6200 DSL modem to accept access via a remote PC? I have a security camera that can be viewed via remote computer access, but I cannot configure my modem to accept a remote access.
My Comcast cable modem does not have a 2nd port needed to connect my Belkin AC1200 wireless router. Is there another way to configure this or are my options to either buy a new cable modem or try to upgrade it through Comcast?
How can I configure Belkin N1 Vision Modem router to use Back to My Mac? Bcos in iCloud preferences its give me a error message "setup router for better performance"
How can I configure the Cisco 515E (version 6.3(4)) to be used with ADSL modem. Currently the compuerters are directly connected to the ADSL modem to get the priviate IP addresses and we would like to add the Cisco firewall after the ADSL modem.
config to setup PPPoE on the cisco 831 router to be used with a modem in bridge mode. I have tired other peoples configs found on the web but, not all the commands were available on the IOS version thats on the router. Also note that I bought this as a used router and I dont have a service contract so I am unable to download an updated IOS. The router ver is 12.3(7)T9 and the IOS is c831-k9o3sy6-mz.123-7.T9.bin. Running config below is last tried still could not connect or get ip address from isp. [code]
my computer is a dell dimension 1100, with a Linksys WMP54G wifi card, running vista home basic.In the wifi thing in the notification area, it shows two wireless networks, One is my normal SSID (Lower Net), and one is "Unidentified network". They are both on one wireless connection (Wireless Network Connection 3). When i try to go on the internet, it says i'm not connected. i tried disconnecting from the unidentified network, but that disconnects me from lower net too.
I can use MSN and SKYPE and play games in normal mode but i cant browse web pages properly. They are insanely slow or not working at all. I tried to run in safe mode and everything seems to be fine in there. I tried opera, ie, chrome, mozilla. I saw some post that telling people to run hijack and send the log file so i am sending the log file.[CODE]
Hi guys. I'm running Windows Vista SP2 on a Dell Laptop XPS. It seems there were some viruses on the system which I have cleaned out, I believe. I have restored some issues with damaged registry and the system seems to be working great other than I cannot get a strong connection to the internet. It will open up when I first log on, but then the connection is intermittent at best. If I log into safe mode with networking then the connection is perfect, no problems. What I can do to restore the connection to the internet?
Logfile of Trend Micro HijackThis v2.0.4 Scan saved at 08:36:37, on 9/9/2012 Platform: Windows 7 SP1 (WinNT 6.00.3505) MSIE: Internet Explorer v9.00 (9.00.8112.16448) Boot mode: Normal