Cisco WAN :: CE500-24TT Unable To Access Some Devices
Oct 24, 2012
Setup CE500-24TT switch Port
FE2 router / ports
FE1,3-24 desktop / Ports
GE1-2 Switch ports - MAC filtering is NOT enabled.
8 Port G Switch = SBS2008 / Win2003 with Citrix / Win2K8 Management Server - plus a couple of desktops for Gig to server access.
I connected on the 8 port Gig SW a new Server running Windows 2012 Hyper-V and am not able to ping the PIX - I disabled the firewall and made sure the network location of the HV server is set properly. From the PIX if I try to ping the HV server it fails but I can do a sh arp and the MAC address of the HV server is there. I can ping the HV server from any other device connected to the Gig SW. I can not ping the CE500 from the HV server but I do see the HV server MAC address in the MAC table of the CE500 SW. I tried plugging the HV server into G1 on the CE500 and same thing - the MAC shows up on the correct port but no traffic seems to pass. I have had issues with this switch in the past where a printer would not communicate between the Gig ports and the FE ports - I moved the printer to the Gig switch and made all the users print via print server and forgot about it.
View 2 Replies
ADVERTISEMENT
Apr 10, 2013
I'm trying to do a Master reset on my Catalyst Express 500 (WS-CE500-24TT v01) and I'm having troubles with this. url...I do everything as it says, but when I plug the cable and I pull up the Web browser nothings appear, just the message that I don't have a Internet connection. The LED port on switch don't stop blinking as LED setup either. Is there another way to do the master reset?
View 0 Replies
View Related
Aug 19, 2012
I just switched to the EA4500 Router and I'm now unable to remotely access my camera devices. I have done the port forward. I can access the cameras from my local LAN both when using the local 10. ..and external 99 .. Addresses. When I go off the local connection - Access does not work. Slingbox did its auto configuration and I can access it. I just cant get to camera devices (Panosonic, Foscam, etc.).
View 3 Replies
View Related
Jan 27, 2013
I have N600 HD Wireless dual band N Router. have successfully installed the router on wireless mode, however I have the following problem in accessing the storage devices connected to the Router.I can see the storage devices connected to the Router in the "Belkin USB Print and Storage center", but when I double click to browse the devices, it does not open up.
View 1 Replies
View Related
Nov 27, 2011
I am trying to factory reset CE500 switch, as described in the factory rest section of the documentation. I do not get an IP address via DHCP from the switch.
On boot up I hold the setup button down, wait till the lights go solid amber release setup. wait for a port on the switch to start blinking green port 1 starts blinking green, plug my pc into port and wait for IP..and keep waiting !!!!
I have tried this on 3 switches now all with the same result.... NO IP offered.
View 1 Replies
View Related
Apr 27, 2010
For any still having trouble with the intial config of a CE500 Switch using Windows 7 / Vista...
Sure all of you have heard of the setup button and how to use it, its obvious Windows 7 / Vista do not properly recieve the DHCP, maybe an issue with the some new Microsoft legislation, the install address of the device in its setup phase, which you can read by the setup led burning steadily is 169.254.0.1
You wont be able to connect to this address in Windows 7 / Vista if you configure it statically, you will be able to view the Gratituous ARP from the Device using Wireshark, in the Windows 7 / Vista network adapter tci/ip v4 settings click on the advanced tab, there enter 169.254.0.1 as the default gateway, press the Setup button on the switch, wait for it to blink, connect your utp cable to port 1 check that the Setup LED is burning stable, type 169.254.0.1 into your web browser and enter a management IP address for the switch, alternatively use Cisco Network Assistant.
View 7 Replies
View Related
Sep 8, 2010
configure port security Cisco 500 Swich ? There is no CLI mode in this switch?
View 2 Replies
View Related
Apr 19, 2012
I try change the configuration the port in the switch catalyst express 500, i need disable switch port port-security, a try with http://10.1.1.1/exec and save configuration with wr command, if a check the configuration de port is correct but i reboot the switch and check the configuration the port appear the switch port port-security configuration again.
View 3 Replies
View Related
Jun 29, 2011
I have just recently replaced a WS-CE500-24LC switch with a SG200-50P. I have plugged in a Cisco 1760 router with a fast ethernet into the switch. On the console of the router I now see these messages: [code]
As far as I am aware both ends of the link are set to autonegotiate the speed and duplex.
View 2 Replies
View Related
Jan 29, 2012
I am having problem in upgrading Cat2960 because I deleted the flash in this switch already and now I need installing an IOS image? [code]
View 1 Replies
View Related
Jul 1, 2012
I am not sure why the CRC and input errors are increasing in fastethernet port...This port is used as Intradomain cross connect to Data Center service provider for LAN extension between two Data Centers in different locations... The link is 100 MB. The switch port is directly connected to patch panel of DC provider and I believe they have some L3 switch or some other device that is providing LAN extension...
#sh interfaces fastEthernet 0/23
FastEthernet0/23 is up, line protocol is up (connected)
Hardware is Fast Ethernet, address is 0019.3050.1497 (bia 0019.3050.1497)
Description: ASA_VPN_TO
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
[code]....
View 26 Replies
View Related
Oct 2, 2012
I am not sure why the CRC and input errors are increasing in fastethernet port...This port is used as Intradomain cross connect to Data Center service provider for LAN extension between two Data Centers in different locations... The link is 100 MB. The switch port is directly connected to patch panel of DC provider and I believe they have some L3 switch or some other device that is providing LAN extension...
#sh interfaces fastEthernet 0/23
FastEthernet0/23 is up, line protocol is up (connected)
Hardware is Fast Ethernet, address is 0019.3050.1497 (bia 0019.3050.1497)
[Code].....
View 3 Replies
View Related
Mar 1, 2013
After not seeming to be able to save any configurations in 12.2(25)FX, I thought an upgrade would work since it said it didn't recognize my browser or OS but let me continue. I was able to see everything just couldn't save changes.
I updated to 15.0(1)SE3 and everything seemed to be going well. Tried to log back in HTTP (have not set n IP yet since it is still at my house... DHCP seems to be working) and I get a user/password screen that says level_15_access and it won't let me in.
Attempts to log in terminal have been unsuccessful. I can log in my dell switch which I am replacing and my APC units terminal just fine using USB to serial and Ubuntu.
I tried cisco as a password, user and password, admin, administrator no luck.
What is the best way to resolve this, is there a sure fire windows serial program or settings I should use in linux (currently 9600,8,N,1) to connect? I have looked through manuals till I am blue in the face.
View 5 Replies
View Related
May 3, 2013
I am trying to configure 802.1x RADIUS Authentication on cisco 2950-24TT-L Switch. I am using following set of command as given below
Switch# configure t
Switch(config)# aaa new-model
Switch(config)# aaa authentication dotx default group redius
Switch(config)# dot1x system-auth-control
Switch(config)# inter fasteth 0/1
Switch(config)#dot1x port-control atuo
I am facing problem dot1x command is not working on interface.
View 1 Replies
View Related
Dec 15, 2012
does the WS-C2960-24TT-L switch support power over Ethernet ?
View 2 Replies
View Related
Jan 10, 2012
ws-c2960-24tt-L Ethernet switch adding or removing any device from switch cause a loss of connection to all other devices on switch for about 60sec.
View 1 Replies
View Related
Aug 22, 2011
Not able to see devices in CS device management (0 devices).but devices are visible in other modules like RME and DFM.
View 3 Replies
View Related
Jan 16, 2013
My internet comes to D-link 655 wireless router from there I have wired connection, one of the connection goes to a switch from this switch I connect wired devices in my office.Another connection from D-link 655 router goes to another wireless router in my living room which is a Linksys router. My few devices and a laptop connects to this router.My problem is I am not able to see the devices connected to my Linksys router from my office devices
View 2 Replies
View Related
Jul 10, 2012
W7. Internet connection is through BT Home Hub2 and is hardwired. No problem at all. But my wireless connected BT internet radio and my wife's Kindle can no longer connect to the internet. The radio says connecting to network but does nothing. I have changed nothing I am aware of. I have looked at the BT Home Hub Wireless set up page and the settings are Using WPA and WPA2 and the correct wireless encryption key is there. Channel selection is automatic. I have changed that to 3 other suggested channels, no result. Frankly it is all Greek to me and I do not know what I am looking at. how I reconnect the Kindle by wireless and the internet radio? (I know I can use a USB to connect the Kindle, but not the radio).
View 1 Replies
View Related
Feb 29, 2012
I have looked through some posts on here of other people having the same trouble, I tried doing the different things suggested and it still is not working.Laptops/desktops can connect to the open SSID perfect, but anything portable such as iPads, Kindles, Phones etc.do not ever get an IP.I'm remotely troubleshooting this issue for a customer and have SSH ability.
View 9 Replies
View Related
Nov 2, 2011
I can't choose any devices when I try to launch a NetConfig Job in LMS 3.2.
I have to check in the job summary if the device on which I'll apply the job is the good one.
Unfortunately, this problem doesn't appear every time so I don't know where to look for an answer.
View 2 Replies
View Related
Jan 21, 2013
I cannot connect to the WiFi router, an all-in-one modem+router provided by my ISP. Now, I run an Ethernet cord from the router to my computer: the computer works just fine. As of a day ago, though, none of the home's Apple devices will connect to the network, despite reboots, password retypes, and shouting at them. Each device (two phones and an ipad) can identify my network, but they cannot join. Additionally, there is an old laptop that cannot connect anymore.
View 7 Replies
View Related
Apr 4, 2012
Sony Vaio laptop model pcg-71314L - unable to connect to wireless devices - after many attempts at fixing - decided to upgrade to Win 7 Pro. Once loaded, there are no drivers/devices/controllers listed for networking
View 1 Replies
View Related
Aug 21, 2012
I'm running Windows 7 on my desktop, and I've had problems since yesterday with my pc. My Vista notebook, ipad3, ipod touch, android based phone and blackberry are all able to connect to the wifi, but my desktop is unable to connect to the wifi or ethernet. Things were working fine until yesterday, when I had to power cycle, after which the desktop connection stopped, though other devices are working fine. My ipconfig details are as follows:
Windows IP Configuration Host Name . . . . . . . . . . . . : DELL-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
DNS Suffix Search List. . . . . . : reliancebroadband.co.in
[code]...
View 2 Replies
View Related
Nov 1, 2012
I was using the Internet fine lastnight switched on my acer laptop this morning and wasnt connected to the router. I tried connecting but it just fails. I'm still able to connect with my iPad and iPod. I tried uninstalling and reinstalling the network adapter however this fails to successfully install. I've searched for hours but can't find a solution. I'm also unable to reset the router etc because I live in china and the router is in a roommates room whose door is locked.
View 2 Replies
View Related
Nov 9, 2012
I can get regarding using the Collobos Fingerprint software through my WRT150N router. I'm using Windows XP SP3 and immediatly after installing (which went extreamy well) it immediatly found and listed all of my home network printers. All of the wired and wireless windows based systems in my house can see and print to the printers without any problem. However, getting ANY of my apple devices (iPad, iPhone etc ) to print will not even show them as listed on the device when I select print on the devices. Collobos says that I have to make sure that Ports UDP 5353 doe Bonjour and TCP 6361 for FingerPrint need to be open both ways for it to work, I have no problem getting into the router settings and have set them up as stated above in Port Range Triggering and enabled. Also made sure Filter Multicast was not check marked in Security. Unfortunatly, that doesn't seem to work as I had hoped.
View 3 Replies
View Related
Sep 28, 2011
I have several devices connected to my EA4500 (two wired computers, two wireless laptops, iPhone, iPad, and a network drive). i have not been able to connect any new devices wirelessly. New laptops, PS3, friends laptops. Error message would suggest that password is being entered incorrectly, but I change the password to very basic word (idiot proof) but no luck.
View 9 Replies
View Related
Jul 28, 2012
We have Cable DSL modem that connects to router. One wired connection from router to PC. Wireless devices are 2 iphones 2 ipads and 2 imacs. Constantly having to power the WRT120N off and back on to regain connectivity.
View 2 Replies
View Related
Aug 7, 2011
Setup my DCS-930L for DDNS (Dynamic Domain Name Server) so I can access the DCS-930L via the Internet (couldn't access the camera half the the time while on vacation using mydlink) and can now access the camera using my laptop, Android Thrive, and Motorola Droid 3 via the URL I've created but can only see the video when using the laptop.
I have the DCS-930L set to Java but when I log into the camera with the Thrive or Droid 3 (both Android devices) I don't get video. I can make changes to the camera settings and everything else you can do when logged into the camera but just can't see the video. If I change the 'View Mode' in the video setup to 'Image', I will get a picture on all three devices (Thrive, Droid 3, and laptop).
What do I need on the Droid 3 & Thrive so I can see the video when I log into the DCS-930L with an Android device?
View 7 Replies
View Related
Jan 3, 2012
I have a WRT610N which does not allow me to connect any new devices to the wireless network. This is a recent problem as I have been able to connect new devices before. Devices on the wireless network, those that have been on the network, are able to disconnect and reconnect. Just new devices are excluded. Have gone through the admin screens to see if something is amiss but can not find anything.
View 5 Replies
View Related
Nov 29, 2011
I have a WRT610 and am unable to connect any devices wirelessly. All the lights on the right hand side of the router are on except for the USB connection....what am I doing wrong? The router has worked for about a year flawlessly and last night all wireless connections quit.
View 9 Replies
View Related
Jul 3, 2011
I cant see in my network the devices connected to SE2500 just the SE2500 itself. The internet access of the devices connected to SE2500 is working correctly. Is this a problem?
View 3 Replies
View Related
Jan 2, 2013
I had a BT homehub with regular dropouts. I have changed it for a Belkin wireless router. I am now unable to stream music from laptop to Yamaha 671 or connect with wifi printer.My internet is working fine and I can communicate with my Dreambox and Vu Duo with no problem at all. Both these devices and the Yamaha are hard wired to the router.
View 2 Replies
View Related
