I use one PA-2H on my 7206vxr to connect 2 T3 lease line,Due to the performance issue,I plan to replace my Cisco 7206VXR to ASR 1006, When I check the interface option for asr 1000 series router,I don't find the HSSI SPA for ASR Series Router.Does it mean ASR don't support HSSI(T3)? or other SPA can use with my T3 lease line.
View 3 RepliesFor ASR1000 to support 4M routes, RP2 must be used.
1) RP2 need to have 16GB memory in order to support 4M routes?
2) Need to use ESP20/40 together with RP2?
3) If RP2 + ESP10, supporting route table size down to 1M?
4) 4M routes is shared for both IPv4 an IPv6?
5) SIP card will affect route table size?
Does ASR 1000 Series support DMVPN Hub, and Key Server in GETVPN.
View 2 Replies View RelatedWe are upgrading our incoming Internet service from 30 Mb 10/100 to 100Mb 10/1,000.Will my 2600 series router support the 10Mb 10/1,000 traffic from my new modem?Do I need to change my interface speed from 100 to 1,000? I to be sure my router will support the upgrade. [code]
View 8 Replies View RelatedI have autonegotiation disable on my interfcae what should be duplex setting on other end?
Router#sh run int Gi0/3/0
Building configuration...
Current configuration : 334 bytes(code)
Understand they are using dfferent cat cable. Does Cisco equipment nromally all are 1000-T, how to check they are 1000-T or 1000-Tx, does cat 5 with 4 pairs already support GE speed.
View 2 Replies View RelatedDoes backup interface is supported on ASR?
interface GigabitEthernet0/2/1
description 3750_Stack_1
backup interface GigabitEthernet0/2/2
ip address 100.50.50.242 255.255.255.248
i will going to buy a router 2911 but i want know if support a interface ADSL modulo like backup in case that my primary link WAN Ethernet down and up the adsl link with a module HWIC ADSL pots.
View 1 Replies View Relatedhow ISE support on third party LAN switch, if the requirement is doing 802.1X based flexauth.Refer to the diagram i attached; 01 topology.png
Concern 1: if the 3com switch with 802.1X feature, but still without the full feature to support FlexAuth, policy encforcement, DACL etc. In this kind of situation, will user still able to authenticate (using method PEAP-MSCHAP v2), but authorization just grant with permit any any?
Concern 2: Can i assume i authenticated the 3com switch using MAB? But this will cause endpoint with no 802.1X, am i right?
Concern 3: cisco switch C4507-E, loaded with IOS version Cat4500e-UNIVERSALK9-M, version 03.04 and Supervisor Engine :WS-X45-SUP7-E, is this platform is supported in Cisco TrusctSEC?
Cisco 1900 , 2900 and 3900 have Interface Slots and Service Module Slots , My question is which type of card is support this slot.
View 6 Replies View RelatedAny chance of one or preferably both of these before I flash the router to a more competent firmware?Rather ridiculous that there's no interface counters and no SNMP server. I prefer keeping stock firmware where possible but I need this functionality, it really isn't a big ask.That said I have an E4200 v1, which already looks like abandonware given it's been 6 months since the last firmware update - not amused and no intention of swapping a high performance router for one that sacrifices performance for better NAS functionality.
View 8 Replies View RelatedQ. Does the Supervisor 720 support all existing Cisco Catalyst 6500 series interface and services module, protecting customer investments?
View 1 Replies View Related3 months ago, we upgraded two ASR-100 shelves from IOS-XE "asr1000rp1-adventerprisek9.02.05.00.122-33.XNE.bin" to "asr1000rp1-adventerprisek9.03.01.00.S.150-1.S.bin".Prior to the actual IOS upgrade, we had to upgrade the ROM with this package: "asr1000-rommon.150-1r.S.pkg"We now have two more ASR shelves to upgrade but I have 2 concerns and I couldn't find any answer to them:
1) Can I just use the same upgrade procedure for ASR-1000 and ASR-1002F shelves?
2) I could not find the detailed explanations of the "show platform" command output... And I'm afraid we did something wrong with our two first upgrades since I do no have 15.0(1)S mentioned in the three last lines of the output (0, R0,F0)?
ASR #sh ver
Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Version 15.0(1)S, RELEASE SOFTWARE (fc1)
(…)
System imae file is "bootflash:asr1000rp1-adventerprisek9.03.01.00.S.150-1.S.bin"
ASR#sh platform Chassis type: ASR1002
[code].....
Looking for simple doc to follow for upgrade iOS image for Cisco Asr 1000. Not worried about downtime. New hardware not in production yet.
View 4 Replies View RelatedDo you know if cisco has release new version that fixed COMP-LZS feature on ASR 1000 series ? or any ETA on that ?
View 2 Replies View RelatedDoes the ASR-1000 accept an HWIC module, or must one go to a SIP/SPA for all modules?
View 1 Replies View RelatedI configured the logging parameters on my Cisco asr 1000 , but nothing was sent to my terminal monitor
logging on
logging buffered debugging
logging buffered 5
[Code].....
I have ASA 5510 with 8.4 connected to ISG 1000, when traffic is passing the VPN tunnel is working fine, when the traffic stops, ASA will drop the packet but the VPN tunnel on ISG still up .When new traffic started from ISG side, it will drop, as the tunnel is not up on ASA side.
View 2 Replies View Relatedi have cisco Router ASR 1000 .. i configure it ... i need to connect using PPPOE through gigaethernet ....the error 720 appear to me so where the problem ?????????
Router#show running-config
Building configuration...
Current configuration : 1867 bytes
!
! Last configuration change at 11:18:31 UTC Sun Jan 30 2011
!
version 12.2
[code].....
I came up with a few ideas to Load Balance based on multiple ISPs. In our network setup we have a distribution layer of 3750s going to an ASR 1000 Series Router, which goes out to multiple ISPs, ISP1 and ISP2.
we also have a virtual fortinet appliance behind the 3750. If I say all traffic going to 0 - 126 goto ISP1, and 128 - 254 goto ISP2,and then obviously whatever NATd IP the customer has (ISP1 or ISP2), the return traffic will have to go to that specific IP. The traffic will allgo back to the virtual fortinet on the same interface, so I would assume I would be safe with uPF.I don't know of any ways to load balance based on Link Optimization, without implementing a load balancer?
It just happen yesterday that my brother's laptop can not connect to Wi-Fi - it could not detect any wireless in the range while my macbook can still find many wireless around here. As usual , I will use window troubleshooting. However , this case , it could not identify any problem ; it said " troubleshooting can not identify problem ". My brother's computer run on Window 7 , Hp pavillian tx 1000.
View 8 Replies View RelatedThe internet is working fine though when i bypass the router and go straight through my modem
View 1 Replies View RelatedI have an HP Pavilion TX-1000 Entertainment PC that is really frustrating me. It will not connect to my wireless router. I have had this laptop for at least 3 years and it connects to any other wireless connection I've ever tried ( at my sons with Cox, every airport, overseas, and with my previous Qwest routers ). Since I moved and now have a Qwest PK5000Z router this laptop will not connect. The error message I get is " The network security key is incorrect ", but it's not of course. All other laptops I've used here connect successfully, Dell, Mac, Toshiba, etc.
View 1 Replies View RelatedI have a Realtek PCI GBE Family Controller. I recently reinstalled Win7 and it loaded drivers for the card automatically. I actually didn't notice the speed issue until I went to move stuff around on the home network.
The Device Manager lists the above NIC. Under Properties I have:
Auto Disable Gigabit = Disabled
Speed & Duplex = Auto Negotiate
I tried setting Speed & Duplex to 1.0 Gbps Full Duplex but I only interrupted a file transfer by doing this. (The Network icon in the System Tray indicated that the network connection was lost.)
I am using Cat5E 1 Meter or less cables. I have 2 PCS next to my desk with a D-Link Gigabit Switch sitting on top of one of the computers. AFAIK all ports on the switch support Gigabit.
Does following link/procedure is valid for ASR1004 chassis (STEP4) and not just ASR1013 ?
[URL]
I like to fight spam emanating from my network. How to do it and which equipement to use?I have an SCE 1000 series, i'll like to know if it can do the job.
View 1 Replies View Relatedjust found that on [URL], it stated that Cisco ASR 1000's management tool is Cisco Prime Network Analysis Module, which is same name as software that can be install in SRE of Cisco ISR G2 router for network analysis via web browser.
My question here is this mean Cisco ASR 1000 has built-in support for Cisco Prime Network Analysis Module, which has similar function as the one on Cisco ISR G2 router's SRE?
I have a stack composed by:
Switch Ports Model SW Version SW Image------ ----- ----- ---------- ----------* 1 52 WS-C3750G-48TS 12.2(35)SE5 C3750-IPBASE-M 2 52 WS-C3750-48TS 12.2(35)SE5 C3750-IPBASE-M
All works well, except for the client connected to the gigaethernet ports that do not works at 1000, I am sure that the clients are able to do it. I have done a check on one of 48 port:
SW3750_100_ced_rk0#sh int gigabitEthernet 1/0/24 capabilitiesGigabitEthernet1/0/24 Model: WS-C3750G-48TS Type: 10/100/1000BaseTX Speed: 10,100,1000,auto Duplex: half,full,auto Trunk encap. type: 802.1Q,ISL Trunk mode: on,off,desirable,nonegotiate Channel: yes Broadcast suppression: percentage(0-100) Flowcontrol: rx-(off,on,desired),tx-(none) Fast Start: yes QoS scheduling: rx-(not configurable on per port basis),tx-(4q2t) CoS rewrite: yes ToS rewrite: yes UDLD: yes Inline power: no SPAN: source/destination PortSecure: yes Dot1x: yes
Seems all ok but if I try to disable auto config about speed and duplex, and force it manually to 1000 full, I lost the client when i done it I forced the speed and the duplex to 1000 full on the client too.
I am running Windows Vista and we recently got a new wireless router to work with our Blu-Ray player. The desktop works, but not the laptop. I can connect to the local network, but not the internet. The laptop worked before we got the new router, and it works on another network. Our new router is a Netgear WNR-1000 v3. I get a response when I ping 127.0.0.1.
View 11 Replies View RelatedMY RE-1000 is up and working at 192.168.1.141. But I get nothing back when I put this address into IE.
View 3 Replies View RelatedI've had my Vostro 1000 Laptop for almost a year now. I had to reload the O/S. I put all the CDs in and downloaded all the drives, but now I don't show the WLAN card/connection.. nothing.
I can't connect to the internet and when Iook at the network adapters it only shoes the Broadcom 440x 10/100 intergrated controller.. My modem is only showing Conexant HDA D330 MDC v.92 modem.
I had the internal wireless with my laptop when it was given to me as a gift... and have been able to connect via wifi, etc.. but since reloading the O/S and all drivers, etc.. I don't have internet? Can't find this wireless connection?
According to the Time Warner website, my Road Runner Turbo with Power boost is capable of download speeds up to 15 Mbps, which seems to be far surpassed by all wireless routers. So what are the benefits of routers such as the Netgear WNR2000 and beyond with speeds up to 300 Mbps vs the Netgear WNR1000 with speeds up to 150 Mbps?
I'm more than willing to spend more for increased performance, but don't fully understand what benefits I'll see by dropping more than about $40 on something like the WNR1000.By the way, I'm in a two bedroom apartment and regularly have two laptops, a PS3, and Droid X connected to the internet.
I'm using an XFX 750I motherboard and a D-link DWR-112 router to connect to my network. It is showing that it's using 100 Mbps when connected through above mentioned motherboard's Ethernet port. Can I get 1000 Mbps i.e. 1 Gbps networking speed in my local area network?
View 3 Replies View Related