How do you determine who's connected to my wireless router?
I can see the "lan computers" section under the "device info" section under "status". It lists computers that were connected yesterday but have been powered down for at least 12 hours? Renew'ing or releasing the router doesn't update the list.
Also is there a way, from my router, to force a computer off my network?
So I have a DIR-825, I got from a family member as they didn't need it anymore. (Don't know if its under any warranty at all) I have a few different problems with it:
1. It doesn't install correctly. I insert the disc, the "Checking adapter enabled" finishes quickly and easy. Then the "Checking network status..." goes for about 30 seconds - 1 minutes and then I get the "Your new router does not appear to be connected properly." It gives the Follow these steps message of checking connections/resetting/etc, which I have done multiple times without success.
2. Despite the failed install, I DO get an internet connection. It starts to get weird though. I have 3 different connections currently connected to it with the following properties:
Modem>Computer (Wired) - 16 MB/Second
Modem>Router>Computer (Wired) - 3 MB/Second
Modem>Router>Laptop (Wireless) - <1 MB/Second
Modem>Router>iPhone (Wireless) - 13 MB/Second
I've tried looking through the options on my router but nothing looks like it will work .
had this same problem last year and by a fluke i was connected to the internet so my wireless printer could access web services but one of my computers connected to the router kept disconnecting from the internet so i had to change the settings now i want to try to get the router connected to the internet again. my wireless network has no internet access so i know the router isnt connected to the internet but i am online right now through the router. My ISP is AOL Canada. I also had a message on the computer saying that the DNS server isn't responding. Also my internet has no network access. Also i had the router set for DHCP NOT PPPoE or whatever its called. also what DNS should i put for the setting or do I need to put that on router setup page for the internet. Also is there any way of stopping the other computer from disconnecting from the internet once i get the router connected to the internet? One more thing on the taskbar at the bottom of the screen where the wireless icon is theres a yellow triangle with an exclamation mark in over it how do i get rid of that when i had the router connected to the internet last year the yellow triangle was gone. And right now on the network map its showing an x through the line going from the router to the internet which i know means theres no internet from the router.
View 14 Replies View Relatedrecently purchased the Wireless N D-Link Router DIR-615. After a few hiccups the router works with all of our computers, blackberry's, wireless printer and Ipod touch's however my Apple TV 1G will not connect to the network. The Apple TV will just give the error code -6 after the password for the network has been entered. I double checked that the password for the router is only WEP 10 hex digits and that it is correct have tried reseting the Apple TV to the factory settings and using the DHCP Reservation in the network settings of the router and manually configuring the TC/IP settings on the Apple TV (Not quite sure what I am doing with this though so put everything back). I have also tried switching the 802.11
View 4 Replies View RelatedCan't get to my Web site with router is connected to my computer and when I connect to my computer with out the router in-line I can connect. I tried the reset in the back but it didn't work.
View 11 Replies View Relatedi recently bought my dir-615 to hook up with my tp- td 8816 modem. After setting it up and successfully working one day, the router randomly stopped sending a WiFi signal. I restarted it twice and it began to work once more. I decided to install dd wrt build 21061 for my E3 dir -615 router. Unfortunately, i could not get it to work. I have dsl internet and my isp uses PPPoE. I used the option for the set up and filled out the appropriate information, but it would not work and the internet light on the router would turn orange.
Unfortunately i decided to play around with this router at the wrong time and the people in my house needed it. I decided to quickly re flash it by going into the emergency room(holding reset button during router reset until orange button starts blinking). However when i select the official d link firmware, it simply will not change. The page is stuck loading on the d-link emergency room page with no progression whatsoever. I tried the process 3 times already.
For some reason, i can connect to the router through WiFi but not through cable. When i connect through WiFi i am on the dd wrt firmware. I don't think i can return the modem to the store since it is clearly on DD WRT firmware.
I'm either looking for a solution to re flashing back to stock firmware, or making the internet work on the dd wrt firmware. The internet light turns orange when i select PPPoE on the set up...
My desktop recently broke so i bought my first laptop. I have AT&T DSL and i bought a new D-Link DSL-2640B modem/router so i could have wireless internet. I installed it and i was able to use it with the ethernet cable, however when i tried to use wifi, it worked for only about 2 minutes before it disconnected.. Now when i try again it says that it is connected (full 5 bars) but it also says there is no internet access and i cannot use the internet.
Also, before, with the old modem i was able to just connect the ethernet cable to the laptop and just start using the internet. Now i have to connect by putting in my username and password provided by my ISP almost like if it was dial up. I don't know why i have to do this now but not before.
Tech Support Guy System Info Utility version 1.0.0.1
OS Version: Microsoft Windows 7 Home Premium , 64 bit
Processor: Intel(R) Core(TM) i3 CPU M 380 @ 2.53GHz, Intel64 Family 6 Model
[Code].....
Since the blackout beginning of this week from dlink I had to reset my camera totally to operate it again. works now again with iphone and with mydlink. But it only works as long it is connected via lan cable to my router. I accessed the set up (via ipaddress) and entered the router details to the setup but as soon I disconnect from lan it does not work anymore. What did I oversee.
MAC OS X
Airport extreme
I need the router's name and can't find it. I've tried every combination I can think of and still no luck. I thought it it might be the SSID but no.
View 1 Replies View RelatedMy D-Link655 is 6 months old. Liked it so much that I bought one for my sister in-law, and my mother/father in-law. Whenever my son's Mac PowerBook Pro (latest Mac OS) is on the network (WiFi) the router intermittently stops working. It loses connection for both WiFi and Wired (at the same time). The intermittent issues seem to disappear when he disconnects the MacBook Pro.
-Current Firmware Version :1.32NA
-Current Firmware Date :2009/07/09
Perhaps it is coincidence, but it seems when the Mac is connected, the router fails every so many minutes (both WiFi and Wired). When the Mac is disconnected, the intermittent issues are gone.
Region : Turkey
Model : TL-MR3020
Hardware Version : Not Clear
Firmware Version : (120817)
ISP : turkcell
I have recently purchased the portable TP link 3020 which is a great solution for me in order to get wifi for multiple users till I get through the long process of getting ADSL in Turkey.The thing is that the 3G bundle Turkcell provided me with is not identified by the modem, so I looked it up on the internet and I found out that I needed to add the bin of the bundle, I searched within the list published on TPLINK website but without any luck.... finally I found the bin I was looking for in another country list... mine is Huawei E353 and the one I found is Huawei E353s2. Anyway I added the bin and still not luck identifying the bundle, I finally resorted to upgrade the firmware which I hate because I always worry of the bad consequence of failure, and unfortunately I was right! Once I upgraded the firmware, I couldn't get connected to the router, it keeps asking me for the key, but without any success! I tried hardware reset by holding the WPS button for 5 seconds as suggested in the manual, but any further success!
Region : India
Model : TL-MR3220
Hardware Version : V1
Firmware Version : 3.14.2 Build 120817 Rel.55520n
ISP : MTS
i am using tp-link router tl-mr3020.. having problem with internet access..it shows my isp (mts) network and got connected also.. it also shows me send and receive data.. but there is no internet access through web browsers .i have tried multiple web browsers (IE / Chrome / Mozilla Firefox)..but the problem remains same.. my ISP network is MTS .. Huwai Device EC-122 with CDMA 2G network.
I have a setup where there are two networks. A 172.16.0.0/16 and a 10.1.0.0/16 that are separated by the dlink router. I am able to ping from the 172 network to the 10 network using a laptop that is directly connected to the router and that laptop can also browse the web fine. However, I cannot ping to that router or access that subnet at all from the 10 network (if I try to access its LAN (the 172 network)). The 172 network is on its LAN and the 10 network is its WAN. I can access its WAN fine. Also, there the router is not recognizing the laptop as a "directly connected deivce" but its not preventing the laptop from using the router. I have tried to make the router as least secure as possible but still nothing.
I thought about making Static Route to point towards the router's LAN but the only option it gives me is the WAN for the exit interface.
Region : Malaysia
Model : TL-MR3040
Hardware Version : V1
Firmware Version : TL-MR3040_V1_120822
ISP : MAXIS
I've got an issue with my TL-MR3040. Need assistance.- Modem HuaweiE398 (Identified) and connected to internet as seen on the webgui. Connected to my TL-MR3040 via wireless and connected BUT no internet access to the web.Tested using RJ45 cable to direct connect PC to Router, NO ISSUE with internet access to web.Need to know is my TL-MR3040 got defects or faulty?
During an installation, we plugged a Ruckus wireless bridge (powered by a PoE injector) into G0/0 on the 1941. The port status remained down/down. We then tried connecting it to G0/1. Again, the port status remained down/down. We took another wireless bridge, plugged it into G0/0 and the port changed to up/up status within a few seconds. The same happened when connected to G0/1. Both ports are have speed/duplex set to auto/auto.We took the cable from the first wireless bridge and connected it a 3550 switch, the FastEthernet port went up/up. We then took the cable and connected it to a switchport card (HWIC-4ESW) that was installed in the 1941 router. The port came up/up.We connected to wireless bridge back to G0/0 in the 1941 and manually set the speed/duplex to 1000/full. The link light on the router became illuminated after a few seconds but no console message was displayed (nor did any events appear in the log) and a "show int g0/0" showed the port status as down/down. This was could not be duplicated as this only happened one time The wireless bridges sit atop of a water tower and are connected each via a shielded ethernet cable. The cable that we're having trouble with is cat5e STP and about 310feet in length. I should note that we have not yet swapped the PoE injector but it seams to be functioning properly as power is getting to the wireless bridge and its accessible. Also because if the wireless bridge for some reason didn't come back up after a power cycle it would potentially mean climbing the tower to perform a hard reset. We tried another 1941 with same results however we have not tried another router model to rule out a potential platform issue. Can you recommend any troubleshooting steps to determine why the port status of the gig interfaces on the 1941 don't come up?
View 4 Replies View RelatedRegion : Canada
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23
ISP : Teksavvy
how can I see who connected to my router?
My 655 router (RevB, Firmware 2.03) is connected from one side to a DSL modem and on the side to two wired PC's and via wi-fi to several other wireless clients (two smart phones and two notebooks). All is well until I try to connect a specific notebook. Connection is estabished for about 30sec and then the router drops ALL connections (including internet and local network!) and I must re-start him by un-plugging from power. This phenomena is specific to a specific notebook since with the other one
View 7 Replies View Relatedi have a adsl modem tp link td 8840, and i had this up and running well for about 3 days. then we decided to get a router cause my little sis got a ipad2.the router is dlink dir 61.so basically i followed all the instructions and the internet was working fine.then for some reason ign site stopped working, i thought that it was down for some reason and didn't think much of it and today when i tryed to go into hotmail or facebook it doesn't work either. so i can get into the log in pages of both, but when i put in the id and password, the screen goes blank and just says waiting for .... on the bottom (using google chrome).and it never loads.i tryed with other internet browsers and it din't work so i took out the router and re wired the adsl modem only and voila. all the sites started working again.i want to use my router but i don't know why i can't acess some sites when i have it connected.
View 1 Replies View RelatedRegion : Austria
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.4 Build 110429 Rel.36959n
I have a problem with the combination of the TP Link router and a samsung smart tv (Samsung UE46ES6300). Every thing works fine, but I can't show videos or images from a usb-hdd connected to the router (Media server is started)I can access the files with my windows pc and windows media-player. AND I can view content on the usb-hdd connected to the router, over allshareplay for windows and send it to the tv.But I want to show videos on the usb-hdd without my pc. I see the TP-Link Router as a source on allshareplay on the tv. When I click on it, there is a error message, that the request can't be executed.
Region : UnitedStates
Model : TD-W8960N
Hardware Version : V3
Firmware Version :
ISP :
My Toshiba laptop can't get connected to the wireless ADSL modem router TD-W8960N. I have 4 different laptops and one desktop, all connected to the router very well, only the Toshiba cannot get on Internet. I can connect to the wireless network on the laptop, but it shows limited access.
I'm have a D-Link DIR-615 Wireless N 300 Router. I didn't use the CD it comes with to set up the network. Instead I configured it manually through the router's settings that are accessed via a web browser.
The main changes I made are:
Secured the router so that a password is required before clients can use the wireless internet. Broadcasting 802.11N only (not B or G).
I can connect to the router just fine and I'm able to access the internet. The only problem is that I don't see any of the other computers in my LAN. When I try connecting to another Wi-Fi router that I have (which is connected to the same network), I can see all of the computer's on my LAN just fine. Therefore, I'm guessing that the reason I can't connect to the LAN is not a problem with my computer and is a problem with the router instead.
I'm on a MacBook Air running Mac OS X 10.6.6.
I have a TP-Link TD-W8960N Wireless Router. I would like to know what the I.P. addresses of connected clients are (both those connected wirelessly & those connected by Ethernet cable). There are about 6 computers in my network, some have dynamic and others have static I.P. addresses.I am finding it difficult to navigate the router,on which menus get me to the information that I am interested in
View 1 Replies View RelatedI'm trying to change some network settings, but the router is unresponsive when I try to connect to its ip address. If I reset the router it opens a 20 second window where I can log in, but then goes unresponsive. I have encountered this on my main pc connected wireless, and duplicated the results when wired in with my netbook.
View 1 Replies View RelatedI have the A1 version. I originally bought it and used it for a few months. I was very disappointed with the performance and went back to my Linksys WRT54G (running DD-WRT).
I recently decided to try it again. I upgraded to firmware 1.13. It worked pretty well for a week or so but now I am considering going back to my Linksys again. I keep losing my internet connectivity. The signal can be strong but internet becomes unavailable. Sometimes, just waiting it out works. Sometimes, disconnecting and re-connecting works. Sometimes, a reboot of the router works. Sometimes, nothing seems to work until it is good and ready to work. Sometimes, I cannot access the internet on my computer but my girlfriend still can. Sometimes, neither of us can connect.
I want to use it because I want the wireless-N speed to transfer files to my media center (and I paid a lot of money for it!) but the aggravation is getting to be too much.
There seems to be some correlation between visibility of my neighbors' networks and the connectivity issues but I could not swear to that. This is amazing to me because my neighbors are pretty far away and I can barely get the DIR-825 signal from my basement to my second floor.
Should the DIR-655 list all devices that are accessing either my WAN or another device on the LAN, assuming there are no other switches on the network, and all traffic is going through the DIR-655?
I was trying to determine the IP, and MAC address of an AT&T Microcell connected to my network. I have no physical access to Microcell. I have been able to find the IP address, in the logs of the DIR-655, but nowhere else. Shouldn't it be listed under SETUP -> NETWORK SETTINGS -> NUMBER OF DYNAMIC DHCP CLIENTS?
I'm using an AMBIT cable modem/router with the DIR-815.The Ambit is in pass through mode.I have 2 wired machines and 1 wireless laptop. I can access the router from all the machines...but none of them can access the internet.
View 5 Replies View Relatedi put the dlink disk in the second computer to install the router and i followed the instructions and i connected the computer to number 2 on the router cause my other computer is connected to number 1. when i tried to sign onto the internet nothing happened and i got a message on the toolbar at the bottom of the screen saying something like local network cable unplugged.
View 14 Replies View RelatedEarlier today my modem died so I looked around and found an old modem (D-Link DSL-300T) lying around so I decided to use that one instead of purchasing a new one.It always worked great in the past, but when I tried it today I can only find a connection on this computer (garbage computer), the other 2 computers in my network can't connect to the internet, they can't even connect to the network at all.Oh and the router I'm using is a D-Link DIR-100. This computer is running windows XP, so is another one in the network and the one I want the connection to work on is running windows 7.
View 11 Replies View RelatedI recently purchased the dir-655 router, and am impressed by it's speed. I had no problems configuring the router to my liking, and have found that all of my wireless devices communicate with it flawlessly.
However, my main reason for purchasing this router was for the USB port. I had hoped to connect my 2TB external drive and have it accessible by all wireless devices in my home. To my understanding, the USB port relies on the use of the Shareport Utility. I've installed the Shareport Utility to my laptop for wireless access to my media files for streaming.
Here's my problem. How can I access my media on my external HDD connected to the dir-655 with Apple TV2? I've read several options for PS3 users... and they all seem to involve leaving the pc/laptop running. I would ultimately like to bypass the necessity of leaving my laptop on... but if that's not a possibility, I can live with it being left on.
Therefore, is it possible to access the external drive connected to the dir-655 with my Apple TV 2 by using the laptop as a bridge? Can I access the content via Apple TV by using Windows SMB just as I currently do to access media stored on my laptop?
To summarize, I want to have access to the media on my external drive connected to the dir-655 via Apple TV2.
I installed the DIR-655 on my home network a couple weeks ago to replace an older model D-Link that failed.
I'm having trouble with my laptop maintaining a connection to the network ever since.
Details:
Firmware Version : 2.00NA , Wed, 12, May, 2010
Hardware Version: B1
Desktop WinXP hardwired to router
Blu-Ray player hardwired to router
Dish Network received hardwired to router
Laptop Win7 wifi
Android phone wifi
CenturyLink DSL
It seems that the wifi stays up until I try to access the internet via the laptop. After a few seconds, the laptop will disconnect, and many times the router seems to reset itself, though not always. This does not happen when using a hard-wired connection. Using the wifi-enabled Android phone doesn't seem to affect the network.
Sometimes the wifi comes back up pretty quickly, but other times it does not. Earlier today, the internet globe light on the router turned from blue to amber. I had to reset the CenturyLink DSL modem for it to work again.
When the network goes does, I get a message on my desktop that a network cable is unplugged, and the network disappears from my available wifi networks that I can see with the laptop. Sometimes I get the "limited connectivity" message.
I have tried changing the 802.11 mode around, and I've changed from Auto Channel Scan to Channel 1. Neither of those have fixed the problem.
I have a wifi connection in my shared accommodation which I use to connect to my Laptop. Now that I have bought a new smart phone, I want to use this wifi with my phone as well. I have a Sony Xperia Neo mobile phone. When I entered the password in phone it said limited connectivity and was not allowing to open the webpages. So what I did was took all the settings of the Wifi like IP address, subnet mask, default gateway, dns 1 and dns 2, manually entered all these in the advanced setting. Now the phone is saying you are connected to the Wifi, But I am not able to open any webpages.
I have a DLINK _ DIR615 router
Wan goes down when transferring files between pcs connected to the lan port.It looks like it's running out of resources or something. Passing more than 10GB of data to other pc is a pain in the ass because nobody else can access internet (lan and wireless clients).Filled a support request in local dlink site. No response so far.
Model Dir-600 B2
Firmware 2.05
2 pcs transferring lan data.3rd pc (doing nothing) can't access router config at 192.168.0.1.
is there any way to interact with wan port like LAN?i have connected a rocket m5 as a bridge to my Dir-615 wan port but i cant see the AirOS login page (rocket m5 configuration page) nor brige's ip address on my LAN...is there any way to interact with the ip address that connected to wan port?
View 1 Replies View Related