We have one router and we plugged a second computer in. We first played Battlefield 3 and both had fine pings. Later, the original computer, which had always used this router was fine, BUT. The other computer began (I guess) to have problems. Diablo 3 and League of Legends had almost unplayable pings (well, around 200). In the meanwhile the other computer was playing BF3 with good pings.
View 1 RepliesI have a mac 10.7.4 and an xbox 360 slim. Whenever I try to play online like cod or fifa and someone else is on the computer It is super lagy, Laging. Before when I had a **bleep**y netgear 33 mb it worked perfectly fine. Now this router is has 300 +mb and it stil doesnt work. This router cost me $80 dollars. Before cisco linsys I bought a netgear not the **bleep**ty neatgear but a newer one and it still had the same problem.
View 1 Replies View RelatedI bought the Dlink 655 about a week ago, it worked fine online via Wi-Fi for my Ps3 for the first few days, then after the first few days it started lagging. It will have little lag jumps every 5-10 seconds and it is really annoying and it really makes playing online impossible. Also it wont let me view videos through the internet on my Ps3, I never had this problem until I got this router
View 1 Replies View RelatedIt won't open on some computers (of different ISP) I;ve tried different Operating systems and browsers... if I check the website, it is mostly up and works perfectly on other computers... If I try to ping it, Sometimes I manage but more often it fails.. Any time the browser says dns error - server cannot be found. I don't know much in IT, but I guess ip doesnt matter, because my computer obtains it from ISP.the website address is armtravel.org... what's the problem ? hosting, 3 ISP-s (that i've tried to open with) or computers (more than 10 don't open)
View 3 Replies View RelatedAt our house we have Fast Access DSL through ATT. We are getting very frequent disconnects and lags. We have multiple devices running off of a single DSL modem/router. It has wireless and wired connections available. Our wireless devices disconnect as frequent as our wired devices do. We have called ATT many times. They have had us replace the DSL filters and did a line test outside our house which came back clear. However, when they run a line test while I am on the phone with them, they say they detect multiple errors on the line. We have replaced our DSL modem with a new one as well. It is a NETGEAR VersaLink Four Port Ethernet Wireless Gateway, Software VER:06.04.12. The self-diagnostics on the Modem come back clean with no problems detected. We get static on our phone line frequently as well.
[URL]
In the technician readout part of my modem I also see this:
1Manufacturer NETGEAR
2Vendor ID b5004946544e449c
3Model NumberB90-755025-15
[Code]......
We just upgraded our internet, which also meant installing a new WiFi router, and mostly it's working fine. The two desktops and two of the laptops in the house all play nicely with the new router, but the third one (an old Fujitsu Siemens AMILO La1703 running Vista Basic) mostly stops responding when I try to connect to the new network. Any other network works fine. I can't actually connect to them since I don't know the keys, but it doesn't affect the laptop. When I try to connect to our new network however, the network connection dialog boxes stops responding and if I try to restart Explorer I still can't open any network related settings or menus. Most of the other stuff works.
I have tried manually configuring the network with the SSID and network key, but the result was just that I couldn't open the network settings at all, even after a reboot, since it was already trying to connect. I have also tried booting up in network enabled safe mode, same thing happens. All drivers are the latest. If I connect it to the router with a cable everything works fine.
my laptop is lagging on all fronts when connected to the interweb and i have no idea why, i dont know what specs you would need in order to diagnose but heres the spec page
View 1 Replies View RelatedI have the Dlink DIR-655, Rev-A, HW 1.35NA Wireless Router Before you ask, I have reset the router to factory defaults, and reinstalled the latest firmware twice, most recently after trying everything else I could think of.I have Cable internet, ALWAYS using wireless, NEVER using wired except for the router installs, which worked just fine until I switched from my old D-Link router to this 655 one a few weeks ago.Now, very frequently, I will open ANY webpage, and the internet will lag, 5, sometimes 10 or 15 seconds and then suddenly it will work properly for a while... only to happen again a little while later - completely randomly it seems.I wired the router to the computer to check to see if the lagging still happened, and everything was fine.I am using a 1-year old Dell laptop, using Windows 7 Home Premium, 64 Bit, and the Network Adapter is Intel WIFI Link 5300 AGN with the most up to date driver confirmed. Under the Advanced Tab for the Laptop's Network Adapter, the settings are as follows:
802.11n CHannel Width for band 2.4 - Value: 20MHz Only
802.11n CHannel Width for band 2.4 - Value: Auto
802.11n Mode - Value: Enabled
There are a number of other settings which I am confident are not relevant, but happy to provide The last setting is: Wireless Mode - Value: 6. 802.11a/b/g In the DLink Configuration, the relevant settings are:
802.11 Mode: Mixed 802.11N and 802.11G
Wireless Channel is on 10, so as not to use the most common "11"
Channel Width Auto 20/40MHz
DNS Relay Enabled
DHCP Server Enabled
Range: 192.168.0.100 to 192.168.0.199
[code].....
Under WAN, the Primary DNS Server numbers are showing and the Secondary DNS Server numbers are showing as 0.0.0.0 McAffee Anti-Virus is up to date and shows no viruses, nor to the Dlink Logs - McAffee Firewall is turned off, Enable SPI in Dlink Settings is turned on.this problem only occurred when I switched routers recently, the old DlInk router I had never had this issue. And I am using a completely different network name with this new router to avoid any conflicts there. And this problem does NOT occur when hardwiring the laptop to the router directly, it only happens via wireless.Storage of the router is fine, it is in the same spot as the old router was, not to hot, not too cold, it didn't eat any metal for breakfast and there are no MRI machines within 10 miles.
Does the 22xx Series FEX support static or dynamic LAGs between itself and a server?Imagine a server with dual 10G NICs, and I need to connect them to the SAME 22xx FEX....can I set up a LAG between the two 10G NIC ports and two 22xx FEX Host ports? Does it depend on how the FEX is connected to the parent 55xx?
View 0 Replies View RelatedI'm having alot of trouble trying to connect more that one LAG between two SG300-52 switches.Basically i have configured both switches with the same vlans. For 2 of the vlans i would like to connect them together between the two switches using LAG. Switch1 has Vlan 5 (ports 1-12) & Vlan 10 (Ports 25-36) with LAG configured on ports 1-2 and ports 25-26. I have setup the second switch identical to the first. But when i connect the LAG's there is no connectivty. If i disconnect one LAG the other starts working.Can you only have i interconnect LAG between switches?
View 1 Replies View RelatedI have a problem running Airplay through the wireless on my W881. It runs okay if the computer i run it from, does nothing else, but if i try to do light browsing or anything like that it starts to fall out and lag. Its like it is not prioritizing the stream at all.
My setup is a w881 running as edge router and i got an Airport express running through a 2950 switch. Airplay runs perfect if i run it through the Airport express or my previous Edge router (Linksys WRT54g). Ofcourse it also runs perfect through the wired network. I shut down all other wireless networks but my w881, because i only want one wireless. And no i dont want to run wireless on the Airport express.
i played around with the Dot11Radio0 interface setting "packet retries 128 drop-packet" and the packet "max-retries". I thought that maybe if i set max-retries to something low, it wouldnt fall out if it has some problems with one packet, it would just continue...
Why there is no parental control feature built in for WAP610N... how do i block website on all computers connected to my router?
View 4 Replies View RelatedI want to set up a Home network between a Win XP PRO/LINUX UBUNTU 10.10(Dual boot) and a Win XP PRO.I need to find out:
A) The IP address of:
1) Each machine on the router
2) The router's IP address
B) How to configure the router using this information Several years ago I saw a tech set up a network using this information but I don't remember how to do it
C) What software I can use on Ubuntu to set up the network
So I set up my router and modem and I have the modem connected to the linksys router and the ethernet port to my computer. The computer with the ethernet cable works fine, but all the other laptops can not connect to the wireless.
View 14 Replies View RelatedI have few computers behind the wireless router. All the computers have static private addresses 198.168.1.xxx. The issue is that when I try to access any computer e.g to use FTP. From outside since I can only use the main WAN IP address when I use FTP I can only connect to one computer basically the one running FTP service on port 21. I can access the wireless router and if necessary can do the port assignments. My question is that if multiple computers are running FTP services behind the router how can I connect to each one of them.
View 1 Replies View Relatedi want to enquire how we can setup a network with 100 computer along with router, firewall, print server, file server. diagram of network to understand the things.
View 1 Replies View RelatedEverything was working fine, and various computers, tablets, and even my smartphone, all hooked up to my router without any problems. Somehow, this week, first my Asus U56E wouldn't connect (before all this it was automatic), and then my Google chromebook wouldn't connect either. The Asus is my main computer. And the reason for writing. I just mention the chromebook because they both quit connecting at same time, pretty much. But still my old xp netbook connects, as does my new google nexus7 tablet. And my nexus one phone. All hook to wifi, with no problem.I tried everything I could think of: This is a Dlink Dir615 router. Even set a new wireless network up, but it doesn't seem to connect. I ran the Windows Network Diagnostics, and it reset everything, and looked like it was fixing it, but no go. It said to investigate router or access point issues. I did what it said, and what has always worked with these problems. Turned off router for about 1/2 minute, then restarted it. Then did the same with the Cox motorola modem, *and* the router, but still, just doesn't want to connect. Wireless, that is...no problem with ethernet.Finally pushed the little pin in in the back of router, and reset the router entirely. Set all up again. Same thing happens, it just doesn't seem to recognize these two computers. So just to be sure, I used my nexus one as a wifi point: and these computers hook up fine, so it seems to be something with the router. My ISP is Cox. Cable. Router D-Link Dir 615, latest firmware. Modem Cox issue Motorola Surfboard. Antivirus Microsoft Security Essentials, and Win7 Firewall (I tried with these two turned off, but still no).I include the xirrus app's output...My wireless network on that app is 'phubai' and that is the one that won't connect. I had trouble bringing it up on Xirrus, too. It would only show when I would attempt to connnect, then it would disappear again.
ipconfig /all
C:Windowssystem32>ipconfig /all
Windows IP Configuration
Host Name . . . . . . . . . . . . : geffASUSpc
rimary Dns Suffix . . . . . . . :
[code]...
I have laptop running Windows 7 Ultimate Edition and an other desktop system running Windows XP.The Laptop is connected to the internet via the router and the desktop is connected to the router via a LAN cable(not cross cable).Is there any way to link these systems together?
View 1 Replies View Relatedjust got internet today and set up the wireless on the router using a laptop connected through LAN. All computer now connect to the router through wireless except the the laptop that was used to set it up.
View 1 Replies View Relatedhow can i use 6 computers with my 4 port d link router
View 1 Replies View RelatedThere are 3 people in my house that are connecting to the internet by a single modem router, everything is fine when there is only 1 of us online , but when there are 2 or 3 of us online , our download & our upload speed dramatically decreases . So is there a way to maintain our normal download & upload speed even when all 3 of us are online ?
View 10 Replies View RelatedI would like to have the best networking on my cyber with a D-Link router, IDU and a D-Link switch so as to connect more than 10 Computers, and send me a mapping of the computers and Manual.
View 2 Replies View RelatedWhat would be the best way to connect 10 computers to a 4 port router?
View 1 Replies View RelatedHave another problem with my new rev B router.
I am trying to configure access control rules, but the list of computers (ip addresses and mac addresses) are empty, I have setup all of my devices with static ip's, they are all turned on and all have internet access. None of the systems including the one I am trying to configure the rules with are there, They don't show up in port forwarding either. Any one ever have this problem? I returned and DIR-825 Rev.b for this same problem because i thought it was defective.
I have tried rebooting the router, rebooting each pc and trying different ports on the router itself. There are wireless and wired computers that I am trying to setup but none of them show up. When I try to manually enter them into access control ie. 192.168.0.103 it will only allow me to put one computer in for each rule.
The old rev.A router this one replaced work perfectly fine with the same cables and computers setup the same way.
I'm using Comcast cable. I have a motorola cable modem. I run that into a Netgear 8-channel router with wireless (that's 8 physical network sockets).I have had these devices hard-connected to the router up until today and everything has been running fine:
* My Desktop (desktop running Windows 7 with Gigabyte motherboard and built-in Realtek NIC)
* T-Mobile VoIP device
* My Laptop (old Alienware running XP with generic NIC)
Today I took my old desktop motherboard from a year ago (Gigabyte motherboard, but not the same as My Desktop, built-in Realtek NIC), gutted it out, replaced the hard drive, got it running Windows 7 and set it up for my kids. Got it connected to the Internet early this morning when my machine was off and it ran fine.While it was updating, I fired up My Desktop and the router stopped working, all machines lost Internet, and I was at a loss.After some troubleshooting, it turns out that if I have My Desktop and the Kids Machine connected to the router and running at the same time, all devices on the router lose connection. I can have the Kids Machine on with the T-Mobile device and My Laptop and they all work. I can have My Desktop on with the T-Mobile device and My Laptop and they all work. But as soon as My Desktop and the Kids Machine come on together, everything gets hosed.The router is set to reserve different IP addresses by Mac Address for every machine. And I've verified that My Desktop gets its IP address correctly, and so does the Kids Machine. They are different IPs.I (usually) know just enough about networking to get a home network set up.
we hadn't have the WEP key on our Linksys wireless router, so we decided, about a month ago, that it was a good idea to lock our wireless connection. So we did. For a couple of weeks, everything worked just fine.But then we bought a new printer, which happened to be a wireless network printer, and in the process of installing it, we mistook the reset button (I think) on the router for some other button and ended up resetting the router. When we did that, we undid WEP key, thereby unlocking the router. Then, we locked the router again, at which point one of our computers--which happens to be mine--ended up not working. All other computers and phones and iPads work just fine, but this one laptop of mine just doesn't work (with respect to wireless internet connections, of course).
- pressing the reset button on the router again. It kind of works. The internet works for about five or ten minutes (which is unbearably annoying because I have to reconnect it every five minutes), but my computer somehow disconnects itself from the internet connection. Also, although the internet technically "works," the wireless network icon thing on the bottom right of the screen has an "X" on it, which I thought meant the internet is not working, but it apparently doesn't, because my internet is working now. And, if I click the icon, it says that I'm not connected, but, again, the internet works. (for about 5~10 minutes, if I unlock the router)
- changing the internet protocol information (I don't think it does anything, but.)
- changing the wireless internet connection property to WPA, WPA-PSK... everything.
*All computers in the house have wireless internet connections but mine.
*When I reset the router, the internet works, although the computer says it isn't connected, and it disconnects itself every 5 or 10 minutes.
I have a SMC Gateway Router and 2 computers connected to it with RJ-45 cable. They are (1 iMac + 1 PC) 150 feet apart both computers are wired to the router. I also have a Canon Pixma MP 560 Multifunction Inkjet printer that has the capability to be connected both wired and wireless. Right now it is only connected to the iMac via a USB connection as all 3 (router, iMac and printer) are on the same workstation.how to connect the printer so it could also support the 2nd computer a Windows PC which is located on the floor below. Can I do that through the wired router too? If not possible, I also have the capability to connect wirelessly although I would prefer to use the wired connnections.The PC has a Belkin USB 2.0 Network Adapter for wireless connection; both SMC Router and Belkin USB adapter are 902.11 N capable.
View 1 Replies View RelatedI have been searching the net for a hub of some sort for a home office. I need it to be able to support printers. It needs to be a wireless router and have a data storage which can be accessed by multiple computers. Like a backup. But the main thing im worried about is if it can be protected by antivirus and stuff.
View 1 Replies View RelatedHow to Configure Router to redirect all internal computers to redirect to a particular website..
View 1 Replies View RelatedI can't seem to receive emails although I can send them and my prinet is off line. Had an IT guy come out and got me to the internet but he didn't make sure I was receing emails or able to print.
View 1 Replies View RelatedI recently switched internet service providers from AT&T to Time Warner and ever since I have been unable to connect to my Netgear router with my computer's wifi. However, I have successfully connected my TV wirelessly to said router. One other note, my computer's wifi seems to recognize that the netgear router is there but it just refuses to connect me to the internet
View 7 Replies View RelatedI have one wireless router, 2 computers, 3 wifi laptops. so i want connect these all things in network.
View 1 Replies View RelatedWe have three laptops in our house. We are set up with internet that gives me a direct connect and up to eight wireless devices. My son and daughter-in-law use the wireless and I use the direct connect. M son added a router (which I have no idea what that does) and set up networking on his computer (which I also have no idea what that does). When I am the only one on the computer, it flys. When either of them get on thiers too, it slowes a little. When both of them get on, I might as well get off because it can take up to three and a half minutes to load a page.
View 3 Replies View Related