My son has a modem that can be wireless or cable. He mostly uses it via cable, but can I set up my wireless computer to use the modem at same time or would he need to have the modem set to wireless? Failing that, could I set up a second modem as a wireless one just for me?
View 1 Replies
I have a new router (ASUS RT-N10)and It is asking me to direct connect my cable modem to my computer, and then find my MAC address via command prompt, and clone it to the new router.I can get to my command prompt, the problem lies in windows 7 and vista's (or mine) inability to realize that my network card is directly connecting to the modem. (No internet connection available, doesn't think anything is connected). I have tried on multiple machines to try and find my modem's mac address but it simply is not working.I want to know if I can find the mac address through the old router, or what I need to do to have windows 7 recognize I'm directly connecting the modem to the PC.
View 3 Replies View Relatedmy computer randomly disconnects from my modem and will not reconnect until I restart my computer (do not need to restart modem). When I check the modem, it always is still running. The lights on the modem do the exact same thing whether the internet is working or not. The disconnection is entirely random. Sometimes it will disconnect immediately, sometimes it will take up to a few hours. I do not have a router hooked up to the modem, and the only other thing the modem is hooked up to is our tv. But even when the tv box is off, we still randomly disconnect.
On the previous forum thread that I read, some of the comments asked for the person to paste their entire ipconfig and their entire ping list from command prompt I will post that below: [code] Could it possibly be a virus? I am currently performing a virus scan using Microsoft Security Essentials. I will report the results of that tomorrow, seeing that it will take several (up to 10) hours to finish and it is nearly midnight of me posting this.I should also note that whenever I unplug my Ethernet cord it gives me a symbol that looks like this other than the regular disconnect with the red "X" over the wire symbol.
I just got a WAG160N-au, I run the installation disk, follow the procedures. I got the internet connection.
View 9 Replies View RelatedI have a modem Scientific Atlanta 2100. I just installed windows 8 pro 64bit and when installing the driver to use the usb cable modem does not recognize it and simply not installed. I wonder if it is possible to use my usb cable modem or simply incompatible with my windows 8 64bit pro.
View 3 Replies View RelatedWith this modem, can you hook up to the Linksys Smart Apps WiFi?
View 2 Replies View RelatedI inherited a BEFCMU10 v.3 cable modem from my boss who switched to FiOS and I would like to use this with my Comcast connection.All I received from him is the cable modem and power adapter, what do I need to install and get this cable modem working? My router is WRT-54G.
View 2 Replies View RelatedI can't get a new IP from my ISP when my Cable modem router(EPC3925) is set to router mode, i have tried factory restore, unplugged etc..but still no luck. It changes each time i reset it when i set it to bridged only mode but then i won't be able to connect other devices to it since it doesn't uses DHCP in bridged only mode. It changes back to the IP i had when i set it to router mode. I don't want to change my router settings to bridged only because it would disconnect the other devices in my house. Why my ISP assigns the same IP address when it's set to router mode but assigns different IPs when it's set to bridged only, how is this possible ?
View 1 Replies View RelatedI have a cable modem installed to my property but want to use my modem/router to go wireless. The proble is my cable modem output is a RJ45 and the router input is RJ11.
View 10 Replies View Relatedsome reference material about configuring my WAG320N to use my cable modem via Ethernet port 1. I've seen it mentioned that's its possible, however I've been unable to sort it out myself.
And before you ask, I've brought the DSL router as I'm moving in the next 12 months and my new base will not have access to cable internet and I'll be reverting back to DSL.
I'm switching to cable internet service instead of DSL. My Netgear router will not work with my cable modem; but it works like a charm with my DSL modem. Is it a problem with the router setup? Good thing I still have the DSL service.
View 3 Replies View RelatedI have quest dsl internet service. in the rural area i live it's the best i can do. I have a leftover netgear CG3000D cable modem. can I use that netgear somehow to wifi my home for my android phone, using the quest net service?
View 1 Replies View Relatedcable company connected cable modem to computer, and left us to do the wireless set-up. during this process, we had to disconnect the ethernet cords and reconnect at correct locations. Now, no internet period. The cable modem is not showing a send signal
View 1 Replies View RelatedI want the best, most super-kickass Docsis 3, Wireless N Cable modem there is. It should come with DD-WRT or something better (if it exists) or be easy to flash to it.
View 5 Replies View RelatedYesterday when I got home from college my computer randomly could not connect properly to my wireless modem. It tells me the SSID etc but when I connect to it, it becomes an unidentified network and has no internet connectivity. This problem only occurs on my laptop via wifi, wifi still works fine on other computers and my phone so I assume it is a problem on my laptops end. Also my laptop can connect to other wireless networks, ie my schools public network, and they work fine. I'm running windows 7 home premium.
View 8 Replies View RelatedI am having wireless modem to connect the internet of BSNL, I Want to connect internet by wireless lan to another pc
proxy settings for connection
i'm trying to connect to my wii n my laptop. i have a cricket broadband hookup to desktop.
View 1 Replies View RelatedHow do I plug the wireless router to the cable modem?
View 1 Replies View RelatedHow to establish two different routers with seperate networks to a single cable modem?
View 3 Replies View RelatedI want to acccess my office computer from Home PC.I have ZTE DSL Modem + Wireless Router and got new Static IP, so how to configure Static IP From BSNL.
View 3 Replies View RelatedEvery few minutes my WGR614v6 loses connection to the cable modem though the wireless in-house is strong. Cable modem being reset does not work. Resetting netgear router brings us back online but only for a few minutes. Have replaced power supply to router and it is still occurring.We have a desktop and 2 laptops online. Also, the notebooks always drop to 18mbps while the desktop stays at 54mbps.
View 2 Replies View RelatedI have desktops hardwired to a switch, which is connected to my cable modem. They pull a 10.x.x.x ip address with DHCP. I have a wireless modem (e3200) connected to the cable modem. My wireless devices pull a 198.x.x.x ip address. Can connect to the internet just fine, BUT..Because of this (im assuming) I cannot add my printer to my wireless laptop. Different networks, wont connect via share name etc.So, if i turn off DHCP and NAT on the wireless router, shouldnt my laptop pull DHCP from the cable modem and get a 10.x.x.x IP address while connected wirelessly?My wired computers can connect to the shared printer just fine, only my wireless computers cannot. I have another printer that is networked (connected directly to the switch, no computer) with a static ip of 10.x.x.199. My laptop can connect and print to it just fine. I just cant connect to the printer that is attached to the 10.x.x.x computer.
View 3 Replies View RelatedHave had ADSL installed through a router, connected the wireless router and it works fine Have since connected the original router via -120mtrs of CAT5 cable to extend to the house. Connection through LAN is fine into desktop however the minute we try to connect an additional wireless router the connection fails. We have even put the LAN from the second Wireless into the desktop and there is no connectivity.We have had a technician come to sort the problem, they advise that they have no explanation as to why the LAN works from the distance but the wireless does not. They have suggested that we need to cut the CAT5 half way and put an antenna up to connect the two routers.
View 1 Replies View RelatedWCG200G ver.2 resets everytime i use wireless
Firmware Version: 2.0.3.6.12-0608
Management has decided to put in a Wireless network and want to keep it sepeate from rest of the network. I have been asked to scope out DSL/Cable internet connections.
I am not familiar with setting up 2504 with dsl router.
Any basic guides for setting up 2504 with a dsl? do i need any static ip addresses for this setup or dhcp lease provided to cable modem would do?
I am trying to connect a Netgear wirless router to my cable modem. I have followed the instructions on the set up wizard but it fails to get a connection with the IP and DNS info I provide.I got the IP address info by connecting intially direct from the modem to the PC and then went to Run CMD and type ipconfig /all. I then started the set up wizard and followed the instructions, turning things on in specific order etc. After input the IP and DNS info it reports an error and tells me to check the address information is correct.My internet is a static IP connection (so it tells me and the IP information doesn't change).
View 3 Replies View RelatedWould this work ?. also, on the back of the modem is a rectangular, not the typical, usb slot. I cannot move the modem because it is connected to the wall. I don't want to use an extra long wire either. What do I need to buy so I can use the wired modem, as a wireless one on my pc downstairs ?
View 6 Replies View RelatedI have linksys router connected to my cable modem. I want to change it Belkin AC900. How can I keep the linksys connected until I have tested set up for Belkin AC900 router.
View 2 Replies View Relatedhow to i connect mu linksys router to my ubee cable modem
View 2 Replies View RelatedWe have kids in the house and I'd like to limit their internet access to certain times of the day but because of the great amount of devices they use (phones, tablets, laptops, etc.) the only way I could think of doing that easily was to set up two wireless networks: one that the adults could use 24/7 and the other that the kids could access during certain set hours.
Here's the equipment I'm working with:
DLink DIR 615 wireless router
DLink DIR 515 wireless router
Motorola Surfboard cable modem S85101U
I plugged the DLink 615 in, set it up for DHCP client and plugged it into the cable modem. I lef the default 192.168.0.1 IP address for the device. On that router, I also reserved the 192.168.0.199 IP address and assigned it to the DLink 515.I also gave the DLink 515 device the IP 192.168.1.1 so I could administer it.I set the DLink 515 to static IP and made the IP 192.168.0.199 and the default gateway 192.168.0.1.I plugged the DLink 515 into one of the LAN ports in the DLink 615.I set a schedule on the DLink 615 to shut down internet access to the DLink 515 at a certain hour and turn it back on at another time.Everything seems to work ok, but at least once a day we have to unplug and plug the routers to reset them.
Our router is connected through a cable modem and If I connect my computer directly wired to the cable modem, I have no problem, it does not disconnect at all.In comes the router in between, when I connect the router and connect my computer through the router WRT54G2, it works initially then I get disconnected after about 1-2 hours. This is very regular. I have a temporary solution by resetting the router via two ways:
1. Go to the admin page, and perform a release and renew IP method.
2. Simply power off the router and then on again.
I have an EA2700 (fimware "classic" 1.0.14.129982) that used to work perfectly fine with a Comcast cable modem. I just recently switched to Charter with an Arris TM902 modem and that's where the problems started. The cable modem will not recognize my router. I have to plug in a computer into the cable model when it starts up. Then I need to clone the MAC address and restart the router (after disconnecting the computer). Why isn't the cable modem recognizing the router when I restart it? I guess this could work if it would be a one time thing but I had to power-cycle the modem and it stopped recognizing the router even with the cloned MAC address. So I had to do the whole spiel again.
Is there any way to make this work easier? Should I update my router's firmware to the "smart" one?
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP : charter, its smarter.
so i have a sb6141 cable modem that is mine and not a lease. it works like a champ when hard wired to my desktop. i just got my hands on a new shiny tp-link wdr4300 yesterday and after messing with it for the better part of 2 hours, something seems to be amiss with the communication between the two. everything will be humming along fine and all of a sudden i get the dreaded PAGE CANNOT BE DISPLAYED. sure as the world i look at the modem and all the lights are off and its resetting itself. and honestly this continues until i pull the power and plug it back up. i think maybe one time in the middle of the night i actually saw it reset itself and then come back online.
