WBR-1310 Router Not Allowing Static IP?
Feb 9, 2013
When I set a static IP on my device, it works for a short time, then it won't connect again unless I do DHCP. It's like the router chooses an IP for the device, and only allows it to use that one.
The same thing happened a while ago with my desktop, I wanted to set a static IP so I could access it from another building, and the router, being the piece of crap it is, reset all the IPs, and wouldn't allow the computer to connect.D-Link WBR-1310, Hardware B1, Firmware 2.02
View 2 Replies
ADVERTISEMENT
Nov 29, 2012
We have a customer that is looking to allow only static IP addresses onto the wireless network via the new 5508 we are putting into place. I can see where to require DHCP but not the opposite.
View 4 Replies
View Related
Dec 12, 2012
The wireless is just beyond my computer's ability to detect. I have a D-Link WBR 1310 Router hooked up to a high gain wireless antenna-yes, clear line of sight. I have no direct access to our community modem or ISP.
View 10 Replies
View Related
Feb 11, 2012
My D-link wireless router (WBR-1310) keeps dropping my internet/email connection. The little green lights are all flashing intermittently except of the one on the far left which stays on. I will have a connection for a little while/few minutes and then it drops.
View 3 Replies
View Related
Feb 20, 2012
I have a DI-604 Version E3 D Link router and I'm trying to allow VPN through the router but I'm not exactly sure how. I have the VPN set up through my PC's but I need to configure the router aswell. Trying to set up the VPN so multiple locations can access it,
View 1 Replies
View Related
Oct 21, 2011
I have the WRT610N and would like to add an extender for the wifi in my house.Does the WBR-1310 work? If yes, how do I set that up? If it doesn't work, any device that can give me a better range in the house?
View 4 Replies
View Related
Sep 22, 2012
recently tried to connect a Samsung BD-EM57C blu-ray player to my wireless network. I have a D-Link WBR-1310. Have one desktop, Smart tv currently on network --no problems. Blu ray will find my network but cannot connect. "unable to connect enter ip address manually" which I did. Fail. "enter subnet mask" which I did. Fail. "Ip address taken enter different address" Now what?
View 2 Replies
View Related
Jan 14, 2012
I just bought the 655, mainly for school/Xbox. My parents use it also, but I bought it for myself mainly (shh). I set it up correctly and got connected, but suddenly I wasn't allowed Internet access. The router connects to my laptop, but won't get Internet access. I called customer service and he didn't know what to do. We tried everything he knew and nothing worked. I don't want to return the router cause I read it was very good, but I need internet for school. I have Rev. A and F/W 2.00.
View 8 Replies
View Related
Mar 17, 2013
I have a 7100 router that has some servers behind it. I need to translate each server to a public IP. The only thing is that between the outside world and the router is an ASA. We have a small data center where the ASA is connected to a core switch on the inside and the ISP on the outside. How would I do the NAT/PAT translations on the 7100 and then have them pass through the ASA? for example:
View 6 Replies
View Related
Oct 4, 2011
I am trying to configure Zone Based Firewall (IOS 15.2T) on Cisco 881 router for IPv6. Current setup is simple:
Zone:
LAN --> WAN zone security LAN
zone security WAN
!
class-map type inspect match-any Internet-cmap
match protocol dns
match protocol http
match protocol https
[ code ] ........
Current configuration behaves as expected for IPv4, but blocks all IPv6 traffic. If zone-security is removed from WAN interface IPv6 works normally (connected to Internet). As soon as zone-security is enabled on WAN interface all IPV6 traffic is discarded when connecting to Internet from local LAN.
Error messages on console: Half-open Sessions source destination tcp SIS_OPENING/TCP_SYNSENT
Are there any special settings for ZBF which should be turned on for IPv6 protocol?
View 1 Replies
View Related
Jan 7, 2012
I have just started using my D-Link 1310 Router after quite a few years of it laying around. I managed to get as far as connecting my D820 and my Desktop in a basic Network. I have Windows XP Home on both the Desktop and Laptop. The next step I want to accomplish is making the Laptop wireless with my apartment. When I first had the Router, I of course had Technical Support and my Warranty with Dell was still active, so I was walked through the process and took notes. The only file I made note of for this step was installing the driver (US) WLAN Card Rev.A12, but there must be something else that enables the WiFi catcher because I don't have any icon in the System Tray and no way to access it.
I also remember it being necessary to Bridge the Modem and Router, (I believe we did it from the Verizon site). Though I was told recently that Bridging is not used anymore, now they do a thing called "Double Netting"?
View 1 Replies
View Related
Jun 12, 2011
I recently got a new Toshiba laptop, which works perfectly. We already have an HP desktop PC as well as a Dell laptop, which are both connected to an Ethernet router. When I got my Toshiba, I couldn't connect to the router, whether from a new Internet cable, the cable the Dell uses, or the cable the HP uses (it works perfectly fine with Wifi). The next day I got up early and tried again, and it worked. The HP was turned on, and it connected. But then the Dell wouldn't. Over the next couple days, we realized the problem was that the router only allowed the first two computers that were connected to it to connect to the Internet, but not the third one. The router itself allows eight cables to be plugged into it at a time, so I don't see why it's only allowing two computers, whether laptop or desktop, to connect. Is there a possible solution to this?It's an 8-Port Workgroup Switch, Model EZXS88W.Also, our router DOES NOT support Wifi
View 1 Replies
View Related
Jul 23, 2011
My internet speeds are 45 Mbps DL and 1 Mbps UL and my various wireless connections (3 laptops in my household) were achieving speeds anywhere from 25-40 Mbps DL. My router started acting up and wasn't letting anyone connect via wifi so I did a factory reset and set it up the same way I did before (as best as I could), it started working fine again but now the speeds on all the devices that are connecting to at are capped at 18 Mbps. A simple speed test shows that no matter what they won't pass 18 Mbps, I am almost 100% certain this is the router and I was wondering what I might have done wrong or what is causing this.
View 5 Replies
View Related
Nov 16, 2010
I'm not able to logon to WRT54GH-SG over 192.168.1.1. I'm using correct password & have NOT forgotten. I'm hitting 401 page. The support rep told me reset the router which I do not want to before I explore any possibilities.
View 8 Replies
View Related
Nov 3, 2012
My Netgear wireless router had been working just fine and then inexplicably stopped allowing wireless internet access. My modem is fine. I contacted my internet service provider, and no luck. I unplugged the router's power source and plugged it back it in. Still not working. I switched the power on and off. Nothing. I do not know what to try next.
View 1 Replies
View Related
Nov 5, 2011
I just set up my e2000 on a PC using Windows 7. I am additionally trying to set up additional devices on the network. The two that I am currently working with are:Dell Latitude d240 running Windows XP.HTC Evo smartphone running Android
I can't get these on the network through the e2000. They can access the internet through the e2000 but only as a guest and therefore don't have the same level of security. What do I need to do to successfully put the above devices on the network?
View 2 Replies
View Related
Sep 18, 2012
I have recently had trouble with my wireless D-link WBR-1310 Router. Two days ago everything was working fine, my wireless connection from the router to my macbook was fine and the wired connection to my desktop pc was also fine. I went to bed and when I woke up the next day everything was still ok. About 3 hours after I had first turned on the PC that next day my wired connection started spiking and dropping connection frequently, maybe every 5-10 minutes or so. I play world of warcraft and I also use Mumble VoiP Program and my pings in both are over 800 constantly now making it impossible to stay connected to either program. Sometimes it will drop down to regular numbers (25-50ms, I play on eastern servers as I am in NY) but then rapidly jumps back up into the 1,000's. My wireless connection is still fine though nothing has happened to that, only my wired connection is messing up.
I've tried changing my speed and duplex settings on my onboard NVIDIA nForce 10/100 Mbps Ethernet which is what im using but it hasn't worked. When connecting directly through the modem the problem seems to stop so its definitely the router.
Wireless Router: D-link WBR-1310
Hardware Version: B1
Firmware Version: 2.02
[Code]......
View 2 Replies
View Related
Oct 16, 2011
I have a 100mb conection and regularly get 90mb plus speed when conected direct to the modem. If I conect via the E4200 I only get 50mb ? I have tried disabling the firewall and QOS but this has had no effect. I am using a wired conection and the latest firmware. Its almost as the E4200 is capped at 50mb throughput.
View 6 Replies
View Related
Jun 12, 2012
Similar to this issue with the EA4500 - I have the same issue with maping the drives from both PC and Mac - the USB drive is recognized, admin/user names are coreated appropriately, the folder structure is imported into the admin control..similar issue with EA4500 user here
View 3 Replies
View Related
Apr 16, 2012
Recently purchased an EA4500 router and it is connected to the Internet. One of the reasons we purchased this router was to take advantage of the usb port (only 2.0 unfortunately) to be able to share media across the network. I spent over two hours on the phone (4/16/2012) with Linksys Tech support trying to get this feature to work. When using a little flashdrive I can easily find the connected usb device. However, when trying to connect to an external hard drive, it will not connect. I tried three different external hard drives, a Western Digital 500 GB Elements drive, a Western Digital 2 TB My Book Elements drive and even a portable 1.5 TB Seagate FreeAgent drive. Every drive had the same result. In fact after plugging each one into the EA4500 and then selecting Safely Eject and then plugging them into my computer, each one had to go through the Fix process in order to work again. I tried this several times. Linksys Tech Support could not get it to work either, and they even used remote access. When going into the web interface of the EA4500, the router sees the external drives attached to it. However, only the little 16GB flash drive can be seen by the computer. I know there is a list for approved devices that work with a different device, the E4200 [URL]
It looks like my devices are there but nonetheless its not working. Really not sure why the router can see all of the devices but only the computer can see the flash drive.
View 9 Replies
View Related
Mar 7, 2012
I am trying to allow PPTP traffic through my Linksys WRT320n to a PPTP VPN server on my home network.The Linksys WRT320n is running firmware 1.0.05 build 002Mar 31, 2011.I have created a Port Forwarding rule on the Linksys to allow TCP & UDP port 1723 through to my internal IP of the PPTP VPN server,but everytime I try to connect with a PPTP client from outside of my network I get a connection error on the client.Checking the PPTP VPN servers logs I see the following errors (Please note all IP's have been masked) Mar 2 11:15:07 ap-01 pptpd[5300]: CTRL: Client x.x.x.x control connection startedMar 2 11:15:07 ap-01 pptpd[5300]: CTRL: Starting call (launching pppd, opening GRE)Mar 2 11:15:07 ap-01 pppd[5301]: pppd 2.4.4 started by root, uid 0Mar 2 11:15:37 ap-01 pppd[5301]: Exit.Mar 2 11:15:37 ap-01 pptpd[5300]: GRE: read(fd=8,buffer=41fe30,len=8196) from PTY failed: status = -1 error = Input/output error, usually caused by unexpected termination of pppd, check option syntax and pppd logsMar 2 11:15:37 ap-01 pptpd[5300]: CTRL: PTY read or GRE write failed (pty,gre)=(8,9)Mar 2 11:15:37 ap-01 pptpd[5300]: CTRL: Reaping child PPP[5301]Mar 2 11:15:37 ap-01 pptpd[5300]: CTRL: Client x.x.x.x control connection finished
From looking at the above errors, it seems as if the Linksys isn't forwarding GRE through to my PPTP server.I have tried various settings, including enabling and disabling the PPTP Passthrough option on the Linksysbut still can't get PPTP to work.What is the correct way to get GRE traffic forwarded through the Linksys?
View 4 Replies
View Related
Oct 29, 2011
I have a Linksys router (model BEFSR41) and I all the outputs going to two computers and two gaming systems (X360 and PS3). I have had the router for over a year and it works fine, but I recently decided to attempt to have my 360 access the media on my computer by linking the two together through the Media Center. To do this, I needed to enable my router to allow UPnP (according to Microsoft help). When I did enable this, the router would disconnect me every 2-5 seconds from the internet, then would reconnect me right away.I have no clue why it was doing this (it occured across all of my devices) so I just disabled UPnP and things went back to normal. How to fix this so that I can have a consistent and stable connection when I have UPnP enabled?
View 1 Replies
View Related
Apr 24, 2013
I posted my complaint on Amazon.com recently. My E4200 router stopped allowing traffic through ports completely. I was able to unplug the power and allow the router to cool, and the router would work for a while then stop after about 10 minutes. I assume that the unit was overheating, but I do not have the equipment of a test facility.I bought a Belkin AC 1200 router which is a bit of an upgrade from Amazon.com. I do not think that there is anything that Linksys can do for me as my warranty expired. I just thought that when I spent what was to me a lot of money the router should have lasted longer.
View 5 Replies
View Related
May 28, 2012
EA4500 Linksys router stopped allowing vizio Internet apps to connect from two different TV's. Problem, Just got brand new EA4500 router and Motorola SURFboard DOCSIS 3.0 High-Speed Cable Modem Model: 575319-019. I have 2 new vizio big screen tv's with internet apps. All was working fine and had no problems but occasional drops or limited access.
One day BOTH TV's could no longer connect. However, The tv's will connect to another access point. therefore the problem does not exist in the TV/s and has to be a problem in my access point (I.E. Router allowing access). Additionally, all other devices connect and work fine. I have already unplugged everything for an extended period of time. Checked for updates on firmware and verified no software needed to be updated. Rebooted router... Am using wpa-psk and feel i shouldn't have to go weep as it was working fine...
View 3 Replies
View Related
Dec 18, 2012
i bought a cisco 2950 series switch to play around with and im trying to set it up to SSH. I have google'd a bit on how to do this and i've sort of hit a wall... i have downloaded the cryptographic image from cisco's website, installed a TFTP server (think this is where my issue lies) but when i do the copy tftp flash global command i keep getting the error accessing "xxxx" message.I have tried allowing the server through windows firewall, disabling windows firewall, allowing access through the router..
View 6 Replies
View Related
Mar 12, 2013
Today I installed the 1.0.2.6 Firmware on a RV180W. I only have now two problems regarding the Static DHCP support in the GUI.
1. Via the Networking > LAN (Local Network) > Static DHCP I have no buttons to Add a new static Lease.
2. Via the Networking > LAN (Local Network) > DHCP Lease Clients I can thick a Lease and click on Make Static IP. The result is an error: Operation failed.
View 3 Replies
View Related
May 18, 2011
Abruptly internet access disappeared. It's a router issue, none of the computers here can connect. Further, I can't access the router through a browser - 192.168.0.1 results in a "Firefox cannot connect" message. I've tried resetting the DNS to no avail. I'm typing via cell phone and it's annoying, but I'm willing to try about anything.
View 4 Replies
View Related
Jul 26, 2011
I've been having a problem with setting up static dns 3 on my WAG, what has been set is...
Static DNS 1: 208.67.222.222
Static DNS 2: 208.67.220.220
Static DNS 3: 208.67.220.222
Now if I look in my router status screen 1&2 are correctly displayed but the 3rd entry is showing my ISP's DNS,
View 9 Replies
View Related
Jun 2, 2012
Why does my D-Link WBR 1310 Router constantly need rebooting? By rebooting I mean unplugging power source for 10-15 seconds then replugging it. This problem has been going on for the last 2-3 months.
View 3 Replies
View Related
Dec 23, 2011
I have a WBR-1310 D-link and was in setup this morning trying to fix my password cause the old one stopped working. Somehow I changed the password and no longer have access to the settings to change it to one that I can use to log on with my other wireless devices!!! Is there a way I can reset the whole thing? I mean something that makes sense to someone who is new to wireless internetting?
View 1 Replies
View Related
Jun 19, 2012
After upgrading to 7.2 on my 5508 WCS, the 1310 APs will no longer join. After a call to TAC they said the 1300 and 1400 APs are no longer supported on WCS. Is there any plan to add them back as supported in future releases?I was thinking I could downgrade my backup 5508 and change the APs to autonomous. Or is there some easier way to make them autonomous?
Also, as a low cost outdoor AP, I guess I am reduced to putting 1262s in a NEMA box with outdoor antennas. The 1552s are way too expensive for the quantity I need. Is there some other inexpensive outdoor AP that will replace 1300-1400 series?
View 6 Replies
View Related
Dec 18, 2012
I am trying to setup a wireless link between two locations, and be able to pass VLANs through the Wireless link.Currently I have two 1310 bridges.I followed the information at url..., but it is only passing VLAN 1 across the link. I cannot figure what the problem is.Both Bridges are running c1310-k9w7-mx.123-8.JEA3. [code]
View 4 Replies
View Related
Apr 18, 2011
Is it possible to make a bridge using a 1242 and a 1310? I have been able to get them to associate together and it appears it will function as a bridge. I have the 12(4) 253 JA IOS for both devices. I would like to use the g antenna on the 1242 for the bridge and the a antenna for wireless clients. The configuration on the web management appears to support bridge root and non root for both devices.
View 2 Replies
View Related
