Did Not Have The Network Cable Plugged In?
Apr 9, 2013
I have been playing on a laptop for the last one and a half year without any problems with the internet. I have never had any lag and a steady ping around 20. On my laptop I was connected to the internet both wireless and with a cable because it tend to lag if I didnt have the network cable plugged in.And yesterday I got my new stationary PC, everything is working amazing but its just one problem. My ping goes skyhigh! On this PC I dont have any wireless connection, only a network cable.I have had this lag now since I got my now computer and its pretty frustrating. On this new computer I have a new anti-virus program (norton) that I am not that familiar with since I used Avira for years so I am not sure if the anti virus protection could be messing something up
View 2 Replies
ADVERTISEMENT
Aug 10, 2012
I have an acer aspire 5552 laptop that wont connect to the internet. When I tried troubleshooting I get the message "network cable not properly plugged in or may be broken". When I go through the control panel/system devices/network adapter the only thing that shows is pdanet. Right now the only way I can connect is through my cell phone using pdanet. How can I get my network adapters to show back up?
View 1 Replies
View Related
Mar 26, 2011
I connected my camera to my router with a network cable. It is a DCS-2121, H/W Ver A2, with firmware 1.04_FR.It received an IP address and I could access it fine with a web browser.Then I configured it to work wireless.I disconnected the cable but the camera wasn't accessible.Since I couldn't find it I re-attached it with a network cable, but this didn't work.So I pressed the Reset button to start over again.However, now I cannot get it to work anymore. When I plug in the camera and have it connected with a network cable to the router the status light remains RED.When I plug it in without a network cable the status led remains RED.When I connect it with a network cable to a computer directly, the status led remains RED.I've tried changing the network settings of my router to use 192.168.0.x as range, but it makes no difference. In all cases the status indicator remains RED.
View 2 Replies
View Related
Jan 30, 2013
I've had this modem set up for over 6 months and this just happened out of the blue. I had no connection to the internet, and the lights on LAN 1 and 3 were lit (only LAN 1 is in use.) I think I went about this the wrong way because now the LAN lights won't light up at all, and the internet light is always yellow. I know it's not the ISP because well I'm writing this post with my modem plugged directly into the PC.
When I try to reinstall the router using the CD I get an error message stating that the Ethernet cable probably isn't plugged in, although it is, as I followed each step exactly.
Now when I try to plug in the PC to the router I can't access the router webpage, and device manager is showing an Ethernet controller with a yellow exclamation mark under other devices. I don't even know where to start.
HW: C1
FW: I resetted the modem in an attempt to get this working again, so I imagine it's at the default now. Besides I can't access the router page anyways.
Region: NA - Canada
Wired Connection
Factory reset: Yes
ISP: Shaw (Cable)
Modem: Motorolas SB5102 - no built in router
View 3 Replies
View Related
Sep 5, 2012
I've got a wireless adapter for my desktop and thats what i've been using for years to connect, but now i'm am trying to get a more reliable connection by having the ethernet cable plugged in. Problem is, as soon as I plug it in the whole computer gets extreamly sluggish or sometimes freezes up completely. If I am very patient, I can very slowly do something things. If I open the browser, it probably takes a minute for it to load. Opening the control panel, the window pops-up but none of the icons will appear until it times out. And trying to use the network icons on the taskbar to get into network settings is impossible. Weird thing is as soon as I unplug it and turn the wifi back on, the PC starts responding super quick again within seconds.
View 9 Replies
View Related
Feb 23, 2013
I've just had talktalk installed and cant get internet unless I plugin cable is there a button on my keyboard I have to press .
View 1 Replies
View Related
Jan 3, 2012
Ethernet cable plugged in but get message "no connectivity plub in the cable" This is after I upgraded my desk top from XP to vista home premium. I've checked my drive (via rhine11) it is working.
View 1 Replies
View Related
Apr 12, 2012
Compaq Evo W4000 with XP professional.Comp works fine when no ethernet cable plugged in - after 10 secs of plugging it in - it freezes Have run malware bytes and combofix already - no change.Disabled everything in startup menu and non Microsoft services Works OK in SAFE MODE with networking though
View 17 Replies
View Related
May 27, 2013
I've got a ASUS AC66 router plugged into my Comcast cable modem (regular dumb modem), it's running the Merlin (OEM-modified) firmware.I've got a Netgear 3400 router flashed with DD-WRT (latest build), it's a replacement for another N router that died on me.
Anyways, I went to set client bridge like always. Main router is 192.168.1.1 so I set DD-WRT router as 192.168.1.2, set the wireless modes to client bridge with matching SSIDs for my 2.4/5GHz radios, input the correct security keys on the security page (AES), then I put the router in router mode (from gateway) Basically, I followed the instructions on DD-WRT's website, which worked perfectly until the other router died.
This time around as soon as the DD-WRT router reboots with its bridge information saved it immediately causes some sort of conflict on my network and kills the internet and all network connections. All devices lose their IP address. It's like the DD-WRT router is somehow shutting down the network and my default router.
View 2 Replies
View Related
Jul 17, 2011
I've just bought a new Dell laptop (Inspiron N5110) and have Windows 7 installed on it. Things happened when my laptop get viruses and I have to re-install everything all over again. After successfully installing Windows, I installed the drivers for my laptop.
The problem is:
I have an internet connection in my house: wired and wireless.
I can connect the wifi zone from my laptop normally. It's ok. But when i plugged in the DSL Cable, the internet connection is always disconnect and then auto-connect again and again :(
The map of internet connection in my house: ISP -> Modem -> Wifi Router -> Wired + Wireless
View 4 Replies
View Related
May 9, 2013
This has been driving me absolutely crazy but I am glad to have found the source of it. Over the past 4-5 weeks ever since i built my new computer, my computer has always had this wierd high pitch noise. I dont know if its coil whine or not, but the sound signature is def not the same as the coil whine that comes from my 7970 card. It sounds more digital.
What could be the cause of this? And what would the remedy be? My ethernet cable is approx 60 ft so it will be a pain in the ass to replace. Or buy another NIC?
edit: forgot to mention....the noise is constant. Not intermittent with usage. No amount of load or idle on the network changes the noise.
View 4 Replies
View Related
Jun 30, 2011
TOSHIBA LAPTOP WITH WINDOW 7 - The LAN port on my laptop does not show a light when the cable is plugged in?
View 1 Replies
View Related
Nov 26, 2012
I just recently bought a new HP Envy m6 laptop that's not even close to a week old yet and I've run into problems with the wired connection. I have two different belkin ethernet cable cords to use and neither of them seem to be connecting whenever I plug them into the ethernet socket on my laptop. I've tried uninstalling the network adapters and updating the drivers. None of that seemed to have solved my problem so far.
Is there anything that I can do to solve this problem? I would be fine with the wireless connection that I'm currently using if it didn't fluctuate so horribly. I live in an apartment complex that provides internet access to me so I don't know what company they are using nor the router that is providing me with the wireless connection. I will be checking in with the management to see if it's not a problem with their internet tomorrow.
As for the network adapter itself, I have a Qualcomm Atheros AR9485 802.11b/g/n WiFi Adapter and a Realtek PCIe GBE Family Controller. I'm assuming the Realtek adapter is the one that deals with wired connections. I'm currently running Windows 8 on the laptop.
View 3 Replies
View Related
Apr 22, 2012
On the basement level, and on level 2, I have in wall junction boxes where the Cat5E Ethernet wires come together. There are 6 lines that go from the level 2 box to 6 wall jacks on levels 2 and 3. There are also 6 lines that go from the basement box to 6 wall jacks in the basement and on level 1. There is also a Cat5E line running between the two boxes.I have wired all these plugs on both ends with T568B standard, and in each box they go into a patch panel. I have used a cable tester to test and make sure all these plugs are properly wired. I have also tested individual computers hardwired linked through to my router (without going through switches) and confirmed that they work that way, so I'm pretty sure I've wired it correctly.
At the second floor box, I have an AT&T 2Wire wifi router and modem, with AT&T Uverse service. I also have a monoprice Ethernet switch. In the basement box, I have another monoprice Ethernet switch (link to the type of switches I have is below). The switches are connected together via the Cat5E that runs between the boxes, and the second floor switch is connected to a free port on the back of the AT&T 2Wire Uverse wifi router.These wall plugs are not all currently used. In fact the problem I describe below occurs even if nothing is plugged into the wall plates.My problem is: when I hook up everything, so my wifi router is wired to the first switch, which is in turn wired to the 6 wall plugs upstairs as well as to the switch in the basement, and that basement switch is in turn wired to the 6 wall plates downstairs... at that point when I plug it in, my wifi stops working. Basically, whenever my router is plugged into this hard wired network, the wifi stops working. When I unplug the network, the wifi comes back (I usually reset it, not certain if it would come back just from waiting).
Interestingly, it doesn't necessarily stop working if most or all of the plugs are removed so the network is not connected (for example, if I just go through one plug instead of all of them)Does a network of wired Ethernet, even if not plugged into anything, cause some sort of a load or drain on the router that could make it stop working?
View 1 Replies
View Related
Feb 25, 2012
My internet service grinds to all but a halt as soon as I plug in the ethernet cable to my desktop. Nothing is running in the background (that I can determine). Nothing is spamming data up or down (that I can determine). I get 40ms ping and 12Mbps downloads on every device I have until I plug in my big boy; then all the speeds come crashing down to 600ms ping and 0.9-1.4Mbps downloads (including the desktop, I have not been able to play SWTOR for weeks now). It's not the provider, (I thought it was) but I switched from Time Warner to AT&T with the exact same results. ASUS P8P67 Pro; I've had funky issues with USB ports and one SATA port died. Other friends suggest I may have an awful bug and I need to wipe and start over. I wouldn't mind doing that, but I don't have a windows recovery disk (my copy is legitimate).
Mobo-as listed.
CPU- i5-2500k stock, not clocked
RAM- 16GB G.Skill Ripjaws X DDR3 1600
View 5 Replies
View Related
Sep 24, 2011
my wi fi light is on the light next to it is not. i beleive its the connection light. keeps coming up that its unplugged but its not. i have unistalled and re installed many time with nothing happening
View 1 Replies
View Related
Dec 17, 2011
I can not connect to the web features when plugged in the router but works fine when plugged in the modem directly.
View 1 Replies
View Related
Jan 28, 2013
I have 2 pc's this one is obviously hooked up to the net, the other one works fine, but when i try and plug it into the modem it tells me no internet connection even when i unplug this one and plug the other in.
View 1 Replies
View Related
Aug 6, 2012
I have a Linksys WRT160N conencted to a pc, Windows Vista I can connect it to my ipod but after a few hours or so, it disconnects and I can get to reconnect again.
"Unable to connect to network "........"
View 4 Replies
View Related
Nov 29, 2012
I think our brand new Belkin router toasted itself after it automatically updated it's firmware. We've had it for three days the first two days we were downloading around 2MB/s, then last night it updated itself and since then it's been crawling around 100kb/s.
I've tried to plug the desktop right into the modem to see if it'd speed back up but it won't give it internet access this way. I've tried rebooting the modem after and before switching cables around but nothing will make it change.
View 5 Replies
View Related
Jul 1, 2011
My laptops internet connection quality is inconsistent. I constantly have to disconnect and reconnect my LAN connection to speed things up or keep things going. Then one day I discovered that if I keep the computer plugged in, the internet works consistently and just fine, but ONLY if I do this
View 3 Replies
View Related
Jan 25, 2013
If I plug an 802.11ac USB WiFi adapter into a wireless router like an Apple Airport Extreme, can the wireless router use that WiFi adapter and then be be able to use the 802.11ac WiFi standard in addition to the WiFi standards it can already use?
View 1 Replies
View Related
Jan 17, 2012
Is there a way that the desktop can get on the internet through the same aircard that is plugged into the laptop? Or will I have to purchase a cell phone card for the desktop too. At the moment both computers are routed thru a satellite modem which I want to get off of.
View 11 Replies
View Related
Feb 28, 2012
I have my internet coming from my DSL modem (of course) and running into my wireless router. Once it is in the router I can't get a connection, period. Not even through any of my router's ethernet ports. This wasn't the case until about 3 o'clock yesterday. If I unplug the cable from my wireless router and plug it directly into my computer it runs fine. If I run it through my Micro-Cell tower and into my computer it runs fine. But if I plug it into a router it won't work through Wi-Fi or Ethernet. I have tested the connections of all the ethernet cables I am using. Figuring it had to be a problem with my router (since it was working earlier and the connection only disappears when plugged into it) so I bought another, same problem. What else could it be? PS: I'm using both a MacBook Bro, a PC, a PS3, and a Nintendo 3DS and none get a signal from the wifi. I always keep the PC hardwired through the ethernet ports on the router and use the wireless for everything else
View 1 Replies
View Related
Jan 31, 2011
Can I directly plug a server into an inside interface in a firewall (Cisco ASA 5510). I'm just confirming that I don't need to have a switch between them.This is the only server behind the firewall.
View 2 Replies
View Related
Jun 5, 2012
For over a year there was no issue with the wireless router, then all of a sudden the connection was lost even though the signal was strong. When trying to figure out what was wrong, I accidentally reset the router. I had not used one before, so I am not too knowledgeable. The router had been my previous roommate's, who had set up the password, etc and I had been using it with that set-up, but now I had no password. I tried to reconfigure and set up a new password through the D-Link administrator, but could not get it to work. It is a D-Link DIR-655 and I am using an iMac. I finally just bought an Ethernet cable and plugged in directly,since I had no password protection. But even with the cable plugged in, I will lose the connection and have to restart the router to get it back - which has even happened while I am using the internet.
View 1 Replies
View Related
Jan 22, 2011
I just bought a new router - Medialink wireless-N Broadband Router model: MWN-WAPR150N I had my PC plugged into the router as a direct connection so I can use my Macbook Pro laptop wirelessly. At first, after resetting the modem (Motorola Surfboard model: SB5101), PC was connected properly as internet was working and same for Macbook Pro. However, the PC connection lasted only for a couple of minutes, more or less before it went "dead". I had it diagnosised and repaired but it wouldn't repair the problem. Each time I reset the modem and router, PC connection was fine but again, "dead" after a couple of minutes.Also, I noticed that after Macbook Pro goes to sleep, when it wakes up, it wouldn't connected either and I had to restart it to get it connected. Macbook is the only one that didn't go "dead" after few minutes, only after going to sleep and waking up.Btw, I did reset the router but no luck in resolving the connection for PC.
View 3 Replies
View Related
Oct 15, 2011
I am not able to recognize adhoc(wireless) connections when I am using ethernet(LAN) connection. Without LAN I am able to recognize the adhoc(wireless) connections and able to access them also.I am using HP laptop model 6530s with Windows7 ultimate and I have installed the drivers provided in the HP portal.
View 3 Replies
View Related
Aug 26, 2011
i have a IBM Think Pad running window xp professional and i can't connect to the internet wireless or plugged in to the router. i have several computers and all can connect to my router.. when i plug in the IBM to the router the PC LINK light on the router turns off and there is no light on the ethernet cable i thought it may have been the cable but it works on the other computers.. I turned off and unplugged the router waited then tuned it back on i also did the same with the computer before connecting them together and still nothing.
View 3 Replies
View Related
Aug 4, 2012
My router is connected from modem to router to pc.It is a Linksys WRT160N.When it is plugged in that way, my pc doesn't have internet access but when i plug it from modem to pc it works.
View 5 Replies
View Related
Feb 9, 2012
when i unplug the computer it nice and bright but when i plug it back in it goes dim
View 1 Replies
View Related
Oct 20, 2011
I have a D-Link DIR-655 Router with a Motorola SB5101. When the computer is directly plugged into the modem i get 10Mpbs but when it is connected to the modem (either wireless or wired) the max speed is >3Mbps.
View 3 Replies
View Related
Oct 16, 2011
just got a new supervisor 4 engine for this catalyst 4503 switch that has ios 12.2 (53) SG installed on it. That's quite a bit above the 7.6 i was working with. I'm having a couple issues now. first, I read that it is supposed to be sending out broadcasts automatically to get it's IP address but it doesn't seem to be. the module i'm plugging into there is ws-x4448-gb-rj45, a 48 port 10/100/1000 module in case it matters. it works other than that. I can plug two computers in and see them and i can plug the network in and they'll both get addresses and internet, but i need an IP on the switch. is there a way to send a manual request for broadcast out or somehow set the IP manually? (I know I can do it in the rommon, but that doesn't seem to do anything)
also, the last module in the switch is a 24 port poe ws-x4224-rj45v. the module is recognized, the status light green, the "show interface status" lists it, but it doesn't recognize anything plugged into it. the supervisor is not configured at all yet, so maybe that has something to do with it, but the other module, like i said, works.
View 5 Replies
View Related
