Cisco WAN :: WIC-1DSU-T1-V2 / Installed DSU / CSU WICs Won't Work
Dec 27, 2012
Today I got a pack of 7 Cisco T1 DSU/CSU WAN Interface Card (WIC-1DSU-T1-V2). I installed 6 of them (4 on a 2811 router and 2 on an 1841 router) and none of them would light up, show up in show controllers, or show up in show ip interface brief. Is there something I have to do aside from just inserting them in like getting software or entering in certain commands? (I installed the cards while the routers were powered off).
View 4 Replies
ADVERTISEMENT
Apr 18, 2011
I have a 3825 router running 12.4t IOS. I installed DSU/CSU part number HWIC-1DSU-T1 in the router and it does not recognize it. Is this the right card for this router? Is there anything I can look at to determine the issue? I think the router only has 32M RAM. Below is a show hardware. Card is still currently installed.
View 2 Replies
View Related
Feb 17, 2013
If ASA5525 with ASA8.6(1)2 can be browsed using ASDM7.0(1), as currently i'm running ASDM6.6(1) if it will work, any document how to do the upgrade using GUI screen?
View 8 Replies
View Related
May 18, 2011
I have a wireless adapter WMP54G for a long time, but recently i updated to windows 7 and the problems begun.
After read a lot of stuffs about this problem, i downloaded a driver by RALINK and installed de adpter. But......on the installation, show two hardware: one is the adapter Linksys WMP54G...and the other can't be installed. So..on the Device manager appear like "unknown device" on the three of "USB controllers"
So...i'm already try a lot of things and can't install this adapter
View 4 Replies
View Related
Mar 25, 2013
I have a Dell Vostro 3460 laptop with Windows 7, 64-bit. My wireless driver is Dell Wireless 1704.802.11b/g/n. I just got this computer in December, and it worked fine for a couple of months, then about a month ago, I started having these problems.
Whenever I turn off or put my computer to sleep and turn it back on, my wireless connection doesn't work. The wireless indicator light on the front of the laptop is not on, and I push the FN+F2 button (which is supposed to turn on wireless), but it does nothing. I checked under the device manager, and the wireless adapter is not there.
After the first time I ran the diagnostics, I reinstalled the driver. The I restarted the computer, and the wireless was working. However, that night I turned of the computer, and when I turned it back on the next morning, the wireless was not working again.Other things I have discovered that sometimes work as a temporary fix:
Sometimes, if I wait 5 or so minutes, the wireless indicator light will come on, and then I can restart my computer and connect to a network, but most of the time, I can wait for hours and it never comes on.If I start in computer into safe mode or the BIOS screen or diagnostic screen, sometimes the wireless will start working after I exit that mode and start into normal operating. For example, one of the times that I ran the PSA diagnostics, the wireless started working afterwards, but stopped working again the next day. Another time, I started the computer in safe mode with networking to see if that would work, and the wireless did not work while I was in safe mode, but then I restarted the computer in normal mode, and the wireless came on.
One time, I went under Device Manager and did "Scan for Hardware Changes." After that, the wireless indicator light came on, and I restarted the computer and was able to connect to a network.However, all of these solutions were temporary, and some of these solutions only work one time but not again.I called Dell Support a couple of weeks ago, and they said that my antivirus program might be stopping the wireless driver from starting up. I have Trend Micro, which came with the computer.
View 3 Replies
View Related
Apr 28, 2012
I have a remote site that still utilizes a single T1 connection to me. For multiple reasons we had to scrap the old T1 and have a new one put in. The old T1 resided on a T3 as channel 25. The new T1 is a standlone point to point. I removed the old config from my 7301 and programmed my 3725. I cannot figure out what is going on but the interface stays down/down. There is no loopback turned on, either manually or by the carrier. The AL LED stays amber regardless of whether or not I have a cable patched down. The CD LED remains green when I patch a cable down. LP is not light.I am using a straight through Ethernet cable to connect my 3725 to the smart jack. If you look at the show output below you will see DCD and CTS is down. Since the remote end was working and I just had the tech move the patch cable from one smart jack to another I am assuming the problem is on my side or with the carrierI already tried changing the clock sourced between internal and line. I also swapped out the WIC card for another one. I don't usually program T1 connections. [code]
View 5 Replies
View Related
Jul 18, 2011
Was wanting to know if these cards are compatable with the new 3945 ISRs or if their is a unique command that has to be run to recognize these. why I'm using these large routers with a T-1. Its too long of a story.
View 2 Replies
View Related
Jan 12, 2012
I just bought two 1760's off eBay to create a home lab. I would like to connect them together but am not sure how. Instead of Wic T1 cards that connect with a serial cable, they are using a WIC-1DSU-T1 cards that have ethernet ports.
I haven't been able to find out much about these except that they connect with something called a T Crossover cable. I assume this is just an ethernet cable with the pins connected in a certain way but am not sure. Are these the same as a standard cross over ethernet cable or something else?
View 3 Replies
View Related
Jul 13, 2011
I recently installed a WIC 1DSU-T1-V2 card into a 1841 router to add to a multilink bundle. I inserted it in Slot 1 and powered up the router and there was a new serial interface showing in the config automatically as s0/1/0. I was able to get it setup with ppp multilink and added to the multilink group. The problem is I need to do a sh controller or sh service-module to see if there are errors happening (I'm using this card as a replacement for an interface that was giving errors with this line before). I can do a sh s0/1/0 and that works but I can't see deeper. I found it odd that the serial port just appeared in the config when I booted without having to do anything, if this is correct behavior and how I see the Controller or CSU info for troubleshooting?
View 1 Replies
View Related
Aug 4, 2011
We are currently moving from 1841 (EOL) to 1921/1941 routers. According to the module support doc [URL] this HWIC-1DSU-56K4 card is supported. We have tried both the 1921 and 1941 with the cards without any luck.
IOS Verison: c1900-universalk9-mz.SPA.152-1.T.bin
System Version: 15.0(1r)M9
Boot Error: %MAINBOARD-1-UNKNOWN_WIC: wic card in location 0/1 has an unknown id 0xB
Show Diag:
WIC Slot 1:
DSU 56K
WIC module not supported/disabled in this slot
Hardware revision 1.0 Board revision A0
[code].....
View 1 Replies
View Related
Dec 20, 2011
My 2691 Router has already 2 serial cards WIC-1DSU-T1 installed, When i install the 3rd serial card and reboot the router, it detects the 3rd card installed but 3rd card has no light.
When i do sh ver it shows 3 cards installed.
When i install this 3rd serial card to other Router then light shows on card and it works fine
So i am thinking if 2691 Router only supports 2 serial cards?
View 3 Replies
View Related
Sep 6, 2011
Is there any chance the Wireless Repeater mode work with WPA2-AES ?If not, which model of AP should I buy to connect it with my wap54g as Wireless Repeater?
View 4 Replies
View Related
Jul 27, 2011
i am using bsnl broadband connection.when i want to connect to internet it is saying that TCP/IP NOT INSTALLED.DISABLE E-MAIL SCANNING IN YOUR SEMANTIC PRODUCT 1003,3. so i removed the semantic anti product. still internet is not connecting. what shall i do?
View 1 Replies
View Related
Feb 9, 2011
I am looking around hwo to know the flash and ram installed in WLC 4402? try looking any command, sh ver not there. even in WCS.
View 2 Replies
View Related
Dec 13, 2012
I installed ACS 5.3 on a VM machine for evaluation. The install went fine as I used the recommended settings in the install guide. All the services are up and running when I issue the "show application status acs" command. I am trying to access the web page via http://192.168.1.199:2002 and it just times out. I can ping the server and the server can ping my machine.
View 2 Replies
View Related
Jul 5, 2012
Main office has a ASA 5520, new office has a ASA 5510. Problem is no traffic goes out when the 5510 is installed, no internet no network connection to servers.I have both config files attached.
View 9 Replies
View Related
Jun 14, 2011
Currently I'm using a self signed cert issued by ACS. We are having an issue where occasionally we see in our Windows 7 logs that Windows did not like the self signed cert from ACS when doing dot1x authentication for our Windows 7 clients. We are using the built in dot1x client that comes with Windows and have the "Validate Server Certificate" unchecked but still see this error occasionally. I've tried issuing a CSR from the ACS server and going to Thwate and getting a test cert but everytime I paste the CSR into the field at Thwate I get an error about invalid cert type. You have to choose from a list of server types. I've tried several different ones. I've also tried issuing the request from a WIndows server and when I try and import the files I get a invalid key error. How to get certificate working from Thwate or Verisign?
View 6 Replies
View Related
Aug 15, 2012
Is is possible to find the iLO IP for a server that has no OS installed? I'm not completely sure how iLO works. I believe the person who needed the IP was going to mount an ISO for OS installation via iLO.
View 4 Replies
View Related
Jun 10, 2011
Just had a new Hub installed today, and it'll connect to the Hub, but then not onto the Internet? Never had a proble with my parents wi-fi. Other people are able to connect just fine.
Microsoft Windows [Version 6.0.6000]
Copyright (c) 2006 Microsoft Corporation. All rights reserved.
C:UsersJamesypoo xD>ipconfig /all[code]....
View 8 Replies
View Related
May 21, 2012
putting cat 6 utp in came conduit as 14/2 48 V for ptz camera
View 1 Replies
View Related
Sep 11, 2012
The drivers for this device are not installed. (Code 28) And is hard for me to reinstall because the reinstall driver's button to click is not showing.
View 1 Replies
View Related
Nov 28, 2012
i installed all the drivers i need and it still wont install broadcom 802.11n , i have been on the phone with till for almost an hour.
View 2 Replies
View Related
Nov 18, 2011
Several months ago I installed D-Link's DIR 655 on my W7 x64 PC. Everything worked fine including NetFlix and being able to view photos located on my PC on my Sony TV. The TV is connected via wired Ethernet cable from the D-Link and I use my cable service signal from the router to the TV.
Then I had to reinstall my OS and although I can still view all the cable companies offerings, including NetFlix on the TV, I'm no longer able to see or view images located on my PC on the TV. I didn't change any of the wiring.
I tried reinstalling the D-Link CD but I can't find where it installs on my PC. It's not listed in the Device Manager or in Programs. I'm wanting to know what version of the D-Link driver I have and to be able to view photos and videos on my TV that are located in shared folders on my PC. I'm the only one who uses the PC.
View 4 Replies
View Related
Apr 9, 2012
I wanna implement the VTP pruning into my network, how can I calculate how much bandwidth I can save after its configuration? Is there a way to calculate this for a network with 30 switches? Does anybody have installed VTP pruning on your network at work?
View 12 Replies
View Related
Jan 23, 2013
I have a Catalyst 3750X and 3750G configured in a stack. I need to break up the stack for failover reasons. My question is how do you determine what license's is on each of the switches. From the below print out. I assume the 3750X has the ip base license and the 3750G has the ipservices license. Is there a command that clearly shows which license's is installed on each switch in the stack? [code]
View 2 Replies
View Related
Dec 26, 2012
i installed Prime LMS 4.2 on Vmware ESXİ 5.0 and then in console screen i create hostname,IP,DNS etc correctly.Then, in LMS 4.2 console screen and another client Win7 PC can ping each other however i cant reach LMS 4.2 via web browser remote client PC.
View 3 Replies
View Related
Jul 19, 2011
how many NM-32A or NM-16A module can be installed on 3745 and 3640 routers?
View 1 Replies
View Related
Feb 21, 2013
I have Cisco AIR-SAP2602I-E-K9 Implemented and connected to PoE Switch but the users trying to conenct this AP don't get IP Address.
Dot11Radio0 is up and Dot11Radio1 is down. SSID are created fine.
Subinterfaces for Agilec0nnect and Agilec0nnect1 is also there on Radio0 and are up.3 There is no output for 'sh dot11 association'
View 2 Replies
View Related
Apr 1, 2011
Because of a virus, I recently had to reinstall Windows 7 on my laptop. Upon restarting, I found out that I cannot connect to the Internet using a wired connection (Ethernet cable). I tried going in the Device manager to try and troubleshoot the Network Adapters, but the only object in that category was "Intel (R) WiFi Link 5300 AGN". In a lower category, "Other Devices", I see two "Base System Device", one "Unknown Device" and one "Ethernet Controller", all of them with little yellow exclamation marks on the icon. I guessed the problem was the Ethernet Controller, so I tried "Update Driver...". It told me that it could not find a driver for my device.
View 2 Replies
View Related
Feb 24, 2013
I just recently installed windows vista on my toshiba laptop model L3O5D. Every thing went smoothly and before you know it I was up and running, with one major problem, I can't find any networks to connect to to access the Internet.
View 12 Replies
View Related
Jul 31, 2011
I just installed a fresh copy of XP on an old Dell E310 my wife and kids use. Just an FYI, I used D-link prior to the re-install with no issues for a few years. Anyway, after XP was up, I put the D-link drivers on. The internet came up and worked like normal for 5-10 minutes, then 'poof', gone. Each time I attempted to connect after that I got a warning message stating I do not have network adapters? I was under the impression that is what D-link was?
View 1 Replies
View Related
Aug 2, 2011
I have a desktop (windows 7) with two administrators. How do I transfer installed videos (DVD's) from one to another?
View 1 Replies
View Related
Jun 13, 2012
I want to install 2 wireless routers for the same home network. I want to know if I need 2 modems to go with the 2 routers or if I only need one. the routers will be placed in different locations in the house.
View 1 Replies
View Related
