Cisco Wireless :: Why AP 500 Doesn't Assign IP To Clients

Mar 13, 2012

We have cisco ap 500 series, it was lightweight, but we migrate it to standalone, now, the scheme is simple.We have a router 2811 and dhcp created on it, also we have f0/0.30 virtual interface with ip of 10.10.30.1.On switch one interface (trunk) goes to router f0/0 interface, and one interface (access) goes to ap.On AP we have BVI interface with 10.10.30.10, and default route to 10.10.30.1.So when we connecting to our SSID, it connect but doestn receive DHCP, and takes APIPA address, why ap doesnt assign ip to clients.

View 12 Replies


ADVERTISEMENT

TP-Link ADSL2+ Wireless :: TD-W8961ND Doesn't Assign IP To PCs Through Another AP

Apr 1, 2013

Region : Spain
Model : TD-W8961ND
Hardware Version : V3
Firmware Version : 3.0.0 Build 120524 Rel.05221
ISP :
linksys1.jpg
I have wifi at home this link installed.
192.168.1.1 is a TD-W8961ND
192.168.1.4 is a linksys wrtt54gl

And I have two problems.

1) I can not see any desktops in my local net, and with old router I could see all, for example (diskstation, dm800, etc...) In my macbook air I can not see my NAS Synology and with old router I do.

2) All PCs that are conected to 192.168.1.4 have not IP. and DHCP in TD-W8961ND is activated.

View 5 Replies View Related

Linksys Wireless Router :: EA2700 IPv6 Dual Stack Doesn't Assign IP Addresses

Feb 5, 2013

My ISP recently started offering dual stack IPv6. After changing IPv6 from manual tunnel to automatic, none of my devices get an IPv6 address from the ISP. In the troubleshooting page, IPv6 address is also empty. I tried resetting the router but had no difference. We have another router (ASUS RT-53N) and it works fine.The ISP is using PPPoE for IPv4. In RT-53N I choose "IPv6 with DHCP-PD" and Interface "PPP". There're no such options in EA2700 though.

View 9 Replies View Related

Cisco VPN :: 5550 Assign Static IP To VPN Clients In Redundant VPN Infrastructure

May 23, 2011

We have a Highly available VPN infrastructure across two data centers. We also use ACS 4.2 servers for authentication. The ACS servers are in teh same "cluster" in a Primary and Secondary fashion.  Site A has primary ACS and primary ASA 5550 IPSec VPN termination. Site B has secondary ACS and redundant ASA 5550 IPsec VPN termination. We also use InfoBlox for DHCP IP address assignments. The two IPSec VPN Head end devices, ASA 5550s, they use different subnets for IP pools for the VPN Clients. Site A uses x.x.24.0 and Site B uses x.y.24.0. As indicated VPN clients authenticate using teh ACS 4.2 Radiius server. I can assign static IPs per user on the ACS server but this can only work for the primary site. Once static IP address is assigned on primary ACS for a user, this status will be replicated to the secondary ACS on Site B. When the Primary IPSec VPN Head End ASA or Internet fails on Site A, Clients on DHCP will work fine seemlessly via Site B. But for the static IP users, you have to change the Assigned Static IPs to match the subnet on Site B. How I can assign static IPs to clients via both Sites without manual intervention. Either via DHCP or ASA. I was trying to stay away from creating multiple Groups for VPN and also avoidng creating local ASA users because these options will not scale well as static user base increases. I need users to get a static IP address from Site A subnet when connected to Site A and get a static from Site B subnet when connected through Site B.

View 1 Replies View Related

3560x Assign Default Gateway To Dhcp Clients?

Jul 8, 2013

I have the dhcp server setup and working on our main 3560x.

The only problem is that it is not assigning the dhcp clients a default gateway.

I was not able to find it in the Cisco documentation and a google search is not useful either.

View 3 Replies View Related

Cisco Firewall :: Pix 515E Cannot Ping Or Assign DHCP Addresses To Inside Clients

May 6, 2011

I have a PIX 515E that I want to use to as a border between my internet connection and my Cisco AIR1131AG.  I have configured the PIX to have the outside interface as a dhcp client which gets its dynamic IP address from the cable modem. the AP is connected to the E1 inside interface. Now I could see the E1 interface from the arp table from the AP but I cannot ping it. From the firewall I don't see the ARP  table  from the firewall. and i cannot ping the AP. what is wrong with the configuration? side note, i am able to connect to the AIR1131AG from my laptop I was not able to retrieve an IP address. 
 
FW1 - CONFIGURATION
 
interface Ethernet0 description uplink towards the techsavvy modem speed 100 nameif outside security-level 0 ip address dhcp setroute !interface Ethernet1 description >>> WIFI LAN ACCESS <<< nameif inside security-level 100 ip address 10.0.0.1 255.255.255.0

[Code].....

View 3 Replies View Related

Routers / Switches :: Dlink DIR 615 Router - Wireless Clients Can't See Ethernet Clients

Feb 1, 2011

I have 4 desktops cat5 to Dlink DIR 615 router. All work fine. Any wireless clients, laptop or netbooks, see the desktop computers for a while then disconnect somehow. All machines can see the Internet through the router at all times. The desktops disappear from the laptop/netbooks but the wireless machines can be seen from the desktop computers but clicking on them gets 'Access Denied' message after a wait.3 desktops = XP, 1 98SE. All laptop/netbooks = XP

View 2 Replies View Related

Cisco VPN :: ASA 5505 VPN Clients Can't Ping Router Or Other Clients On Network

Jun 18, 2012

I have a ASA5505 and it has a vpn set up. The VPN user connects using the Cisco VPN client. They can connect fine (the get an ip address from the ASA), but they can't ping the asa or any clients on the network. Here is the running config:
 
Result of the command: "show running-config"
 
: Saved
:
ASA Version 7.2(4)
!
hostname ASA
domain-name default.domain.invalid
 
[code].....

what I need to add to get the vpn client to be able to ping the router and clients?

View 3 Replies View Related

Cisco VPN :: 5520 / 5510 - Can VPN Clients Communicate With Other Dynamic Clients

Nov 5, 2012

We currently have an ASA 5520 communicating with 10 ASA 5510's, all on static outside addresses.  I was asked to add 5 additional 5510's on dynamic address.  All worked well in testing until it was decided that some of the dynamic clients needed to talk to each other.

My testing shows packets just dying in the 5520.

View 1 Replies View Related

Netgear WNDR4500 - Clients Not Showing Up In Clients List

Jul 6, 2012

I have a Netgear WNDR4500 running the stock firmware, acting as a router for my home. I also have 2 routers that are flashed with DD-WRT (Linksys WRT54G and Asus WL-520GU) running as client bridges. The Netgear is 192.168.1.1 and the other 2 client bridges are 192.168.1.2 and 192.168.10.3. The Netgear router is performing DHCP giving addresses from 192.168.10.100 to 192.168.10.254. I have numerous machines connected to the Netgear, wirelessly and wired, and numerous machines wired to each client bridge. All machines have IP addresses that are 192.168.10.100, 192.168.10.101, 192.168.10.102, etc... Everything is working fine, but I have one question: When I access the Netgear router, it shows the client bridges as clients, machines that are wired and wireless to the Netgear router are listed as clients, but the client list does not show any clients that are connected to the client bridges. I assumed that since the router is performing DHCP that all clients would show up.

View 2 Replies View Related

Cisco Wireless :: WAP4410N Won't Assign IP Addresses

Dec 17, 2012

I have a Motorola Surfboard Modem connected to a Netgear 24-port switch. I bought the WAP4410N to provide wireless connectivity from the switch.
 
All my PC's can get perfect connectivity via the switch but none of my wireless devices can connect at all.
 
Sometimes  I can get 1 PC to connect but what's strange is I can view my networked  folders and such but cannot access the internet.
 
I've upgraded the firmware to the latest May-2012. IPv4 and IPv6 are both set to automatic.

View 1 Replies View Related

Assign Priority On A Wireless Network?

Jan 22, 2012

Is there a way to assign priority on a wireless network? For example, on my home network there are about 4 computers connected, 5 cell phones connected, an Xbox a Wii etc etc. Is there a way to set which device takes priority over the others?

View 2 Replies View Related

Assign Security Key For Broadband Wireless?

Jan 28, 2011

I have a broadband with wireless connection. I am also using on laptop. I want to assign a security key so as to avoid misuse by others

View 1 Replies View Related

Cisco Wireless :: Assign Resilient WLCs To An OEAP 600?

Apr 17, 2012

Possible to assign reslient WLCs to an OEAP 600?
 
The web GUI of the OEAP itself only has a single field to enter the address of a single controller.
 
But, I wonder if once the OEAP is talking to your WLC across the Internet, you can allocate HA settings to the OEAP so that it can fall back to a secondary WLC if your main WLC fails.
 
This is sort of hinted at in the docs I have read, but I have not been able to find it explicitly stated anywhere.
 
It would be nice to have 2 DMZ-based WLCs at two different data centres to allow remote users to have a fail-over solution, but I need to be sure that this is supported before implementing.

View 7 Replies View Related

Wireless Router Won't Assign IP Address To Computer

Jul 16, 2012

There are 6 computers in our home network. It happens every few months or so that router would not assign valid IP address to one of the computers. So, most of the time everything works well, but there comes a moment when one of the computers (but not others) can't get valid IP address.We try turning off and then on the router and it solves the problem most of the time. But, there are cases when turning off and on the router won't solve the problem.

View 3 Replies View Related

Linksys Wireless Router :: Can't Seem To Get E4200 To Assign A Static IP

Aug 24, 2011

I have assigned a Static IP with other Linksys/Cisco wireless routers (WRT54G), but I can't seem to get the E4200 to assign a Static IP. My device is connected to Port 3, with that being the only port (besides my WAN) being occupied. When I enter the following and click Save Settings I get the following error: "Invalid Static Route!"I don't understand what I am doing wrong. This is the exact same as I have done on my WRT54G and it worked.

View 2 Replies View Related

Cisco Wireless :: Can Aironet 1130ag Assign IP Addresses Through DHCP Running

Jan 20, 2010

The 1130ag was the LAP model but I upgraded it to run in autonomous mode.  My understanding is that it cannot assign IP addresses but I just want that confirmed.  It is not connected to a WLC nor a server that can do DHCP.

View 5 Replies View Related

Linksys Wireless Router :: EA4500 - Assign A DNS Address For A DHP Reservation?

Dec 21, 2012

On my EA4500 i've given my Sony Google TV Box (connected by wifi N) a static ip address under "DHCP Reservations". However is there any way to add a DNS server address to this reserved IP so that only the Google Box is affected by the DNS, all the other connected devices remain unaffected? Presently i enter the required DNS address in the google box but i would prefer to do it on the EA4500. I'm using the latest Cisco Cloud fw on my router.

View 3 Replies View Related

Linksys Wireless Router :: E2500 - Assign Static IP To Mac Address

Mar 5, 2012

I"m having one problem though. On my old router it had a feature to assign a static IP to a mac address.
 
So that computer would always get 192.168.10.101 as the IP Address.
 
How do I do it on this router?

View 3 Replies View Related

Cisco Wireless :: 2504 / Assign SSID To Interface That Has Dynamic AP Management Enabled?

Jan 3, 2012

I am tasked with configuring a 2504 wireless controller.  Is it possible to assign an SSID to an interface that has dynamic ap management enabled?

Scenario:
Location1:
1) 10.0.0.0/24
2)192.168.0.0/24 DMZ
 Location 2:
1) 10.0.5.0
 
Both locations are routable using network 1 at each location.  However, I need to configure several access points and send them to location 2.  These access points will communicate with the controller at location 1 on network 1.  Two SSIDs will need to be on network 1 at location 1.  The other SSID will be on Network 2 at location 1.  This network is not routable. 

View 32 Replies View Related

Linksys Wireless Router :: WRT610N - Assign Unique Address To Each Devices?

Jun 14, 2012

2 of my attached wireless devices have the same IP address different MAC address. How can I assign unique address to each of the devices

View 1 Replies View Related

Cisco Wireless :: 1141 - Get 12.4 Code To Assign DHCP Address To Ethernet Interface From Server?

Nov 7, 2012

How do i get the 12.4 code to assign a dhcp address to my ethernet interface from my server? I deleted the default config on the 1141 and searching has not turned up anything useful.

View 1 Replies View Related

Cisco Wireless :: 2504 / Assign IP Addresses To Remote Site Wi-Fi Users From Local DHCP Server?

May 29, 2012

Is it possible to assign IP addresses to remote site WIFI users from local DHCP server and forward all other traffic to 2504 WLC?
 
[WIFI Users] >--------<AP (DHCP server) >------ VPN ---------< WLC

View 1 Replies View Related

Linksys Wireless Router :: Wrt54g - Use Dhcp For Wifi / Assign Private Ip For Pc (wired Connection)

Dec 20, 2011

Could I use DHCP for wireless connection and assign private IP for PC for wire connection ?Will it conflict to each other ?

View 3 Replies View Related

Cisco VPN :: ASA5510 Can't Ping VPN Clients But Clients Can Ping

Feb 29, 2012

I have a strange issue on my ASA 5510 (8.4). I can't ping or connect to the VPN clients but the VPN clients can ping/connect to any inside resources. I have checked all the NAT extemtion entries.

View 3 Replies View Related

Cisco Wireless :: WAP 321 No Clients Can Connect

May 10, 2013

I just purchased a WAP 321 and followed the setup wizard. Its powered by a poe switch. The issue I have is no clients can connect to it. I updated the firmware. I reset to factory and tried setting it up manually till no one can connect. I dont understand what im doing wrong here. Unless its a bad unit. I will have about 10 to 15 clients connecting to it. Its the only ap in the building.

View 12 Replies View Related

Cisco Wireless :: 881-W Wi-Fi Clients Not Getting DHCP?

Mar 8, 2009

I'm monkeying around with an 881-W.  Clients can associate and authenticate to ssid 'test', but they cannot get a DHCP address.  Clients plugged into f 0 - 3 get DHCP addresses just fine. 
 
I've looked at a lot of different guides, ran debugs etc.  When wifi clients make DHCP requests the server never gets them.  So there must be some IRB thing going on.

View 5 Replies View Related

Cisco Wireless :: WLC 2504 - Some Clients Gets IP As Zero

Aug 29, 2012

I've  problem with a WLC 2504. Some Clients like phones and Thin Clients get an IP 0.0.0.0.Software Version is 7.0.235.0. Test with a Laptop seams to be OK. Some printers also got an 0.0.0.0.Around 30% are not OK. also had the log: Impersonation of AP with Base Radio MAC 00:yy:yy:yy:yy:yyusing source address of 00:xx:xx:xx:xx:xx has been detected by the AP with MAC Address: 00:yy:yy:yy:yy:yy on its 802.11b/g radio whose slot ID is 0 The problem is, I cannot go to 7.2 version because I have 2 x AP 1231 and 2 x 1242 AP's.1231 AP's are not anymore supported in 7.2 Version.

View 14 Replies View Related

Cisco Wireless :: How To Tell Which Clients Are Associated With WAP4410

Dec 21, 2010

Can you get a list of associated clients from an WAP4410N? How can you tell who's connected?

View 4 Replies View Related

Assign Application To Use Certain Ip?

Jul 31, 2012

I have a windows 7 pc and i would like to run SKYPE on network A as it uses alot of data.I would like all other programs to run on network Bi notice in skype options it uses port 12406. is it possible to set a rule that all traffic on this port be assigned to the IP of network A?ive read through some forums and i found this link regarding load

View 4 Replies View Related

Cisco :: Assign An IP Address To A VLAN?

Jun 16, 2012

I know that a default gateway is used to log in remotely, but what is the purpose of the IP address on a VLAN?

View 3 Replies View Related

Cisco :: Possible To Use DHCP Pool To Assign IP

Feb 27, 2013

ON ASA, I understand that we can assign a static IP for a specific VPN client, or we can use a DHCP pool to assign IP. Now if I want to create DHCP pools, say pool_A and pool_B, for user A, B and C they use the IP from Pool_A, and user D, E, and F they get the IP from pool_B. Is there a way to do this in ASA?

View 4 Replies View Related

Cisco WAN :: Assign IP To Ethernet 0 / 0 On ASA 5505?

Sep 24, 2012

When I try to set an IP Adress to the Interface ethernet 0/0 I get the following:ERROR: This command can only be configured on VLAN interfaces This Error also come on the Interface Ethernet 0/1. Do I have to set first 2 VLAN and assign the Interfaces to the VLAN so that I can set IP Adresses to the Ethernet Interfaces? tell me what I have to do so I can configure the ASA 5505.

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved