I have a EA4500 that I get error 2315 when I try to Delete,change name,or icon. I did a 30/30/30 and everything worked great,24 hours later I was back to error 2315. I tried re-flashing the firmware, but that didn't work. I get the same problems when I try using the Smart Wifi app. There are also times when I can not access the router using Smart Wifi unless I reboot the router when I get home.
View 9 RepliesI recently upgraded to the EA6500 from the EA4500, however under Linksys Smart Wifi i can still see "EA4500 (offline)".
View 1 Replies View RelatedI have noticed that after the new Firmware Update, the EA4500 will not change to a new public address. I have check my logs and my IP Address is the same going back to a 03/25/2012. I changed my router back to my old E4200V1 and it changes to a new addresses when the old one expires.
View 3 Replies View RelatedHow do I change the username password in the router settings for the linksys ea4500? It only lets me change the password, I cant find an option to change the username.
View 3 Replies View RelatedI have an EA4500 router. It's the latest in a long line of Linksys routers I've owned and I'm pretty familiar with setting one up and making changes. But the EA4500 seems a bit more picky than previous routers. Last night I tried to enable port forwarding for ports 53, 80, and 88 for my xbox. I already had port 3074 forwarded. When I did that and applied the change, I lost all Internet connectivity. I tried cycling the power on the router with no luck. I finally got connected again by going to 192.168.1.1 and disabled those ports. The status page then said I had Internet connectivity but I really didn't at least right away. It took a couple minutes before I was actually able to to connect to the Internet again. What else should I check when it says I don't have internet connectivity?
View 3 Replies View RelatedJust purchased a ea4500 router. Have setup multiple computers/devices already and works great. This computer (HP dv6000 running Win Vista home prem) however will not connect to the internet. It states that it is connected to the router (computer sees router), using the cloud connect app on my iphone i can see this computer, but will not allow access to the internet (local connection only). It works fine with the wired connection. When attempting to use the cloud connect software, it says it was unable to complete the install. Have attempted trying while connected by wire as well, same result. Have deleted the wireless connection and allowed software to find connection, still same result, cannot install. Wireless worked perfectly with previous router (WRT54G) three days ago.
View 6 Replies View Relatedjust upgraded to a Linksys EA4500 wireless router at my small office from an old Netgear. My email now wont send messages out on either my IPhone or my laptop(Toshiba) while using the wireless network. If I turn off Wi-Fi on my IPhone, my email immediately sends the messages. What settings do I need to change? I have Comcast internet and one IMAP email account and one "Yahoo" email account
View 3 Replies View Relatedjust upgraded to a Linksys EA4500 wireless router at my small office from an old Netgear. My email now wont send messages out on either my IPhone or my laptop(Toshiba) while using the wireless network. If I turn off Wi-Fi on my IPhone, my email immediately sends the messages. What settings do I need to change? I have Comcast internet and one IMAP email account and one "Yahoo" email account
View 1 Replies View RelatedI have had my router for about a month and all the wireless lan stuff seems to be brilliant. Recently I signed up to an ISP (Plusnet), and can't access most websites. The ISP has told me that I should take this up with my Router company. I seem to be having the exact same problems as this guy was having [url]....
View 1 Replies View RelatedI have several devices connected to my EA4500 (two wired computers, two wireless laptops, iPhone, iPad, and a network drive). i have not been able to connect any new devices wirelessly. New laptops, PS3, friends laptops. Error message would suggest that password is being entered incorrectly, but I change the password to very basic word (idiot proof) but no luck.
View 9 Replies View RelatedVery strange problem with an EA4500 running 2.0.37.131047. Set it up in no time with a Mixed network on WPA2 Personal, Internet's fine, but I can't see any of my wired clients. They don't ping at all. Even stranger, if I plug into another wired switch port with my laptop, I STILL can't ping the other clients. One is a NAS and one is a network printer so there are no firewalls involved. I power cycled the printer but in vain. I've already reset to factory defaults once, but that didn't work. I'm thinking I'll need to return it.
View 4 Replies View RelatedThere are plenty of instructions to configure USB storage but there are no instructions on how to use it, specifically. Ok, so I have my ftp address, user name and password and tried to connect with Filezilla on my local network. Unable to connect. Also, the USB device does not even show up in Network settings. However, I am able to see the device as a media server from Sony Playstation.
View 3 Replies View RelatedI recently got a ea4500, wireless working fine, can connect to the usb storage from different devices fine, but when i try and copy a file to the usb storage, it initially looks like its transferring and registers a file in the usb storage folder. but when i access the usb storage from other devices i cannot find or access the files that i transferred?
View 5 Replies View RelatedI just switched to the EA4500 Router and I'm now unable to remotely access my camera devices. I have done the port forward. I can access the cameras from my local LAN both when using the local 10. ..and external 99 .. Addresses. When I go off the local connection - Access does not work. Slingbox did its auto configuration and I can access it. I just cant get to camera devices (Panosonic, Foscam, etc.).
View 3 Replies View RelatedI want to do with my ea4500 is assign it a static IP and access it after doing so. But, no matter how many times I try, I cannot enter its IP address in the address bar and see its settings. I change its IP to192 168 1 200. Subset 255... DG 192 168 1 1 DNS same.Under router address 192 168 0 1I CANNOT access this router at 192 168 0 1 at all. The thing is, the **bleep** settings are not any different the. How they were when it was WORKING. I literally took a screenshot of my setting in case a scenario like this would come up, yet it more problems arise. The only way I can access the router is by doing a factory reset and accessing it at 192 168 1 1.
View 9 Replies View RelatedI am not able to access https sites (like banking etc.). Once I plug my old router back I have no such problem. I guess it must be router settings that I cannot figure out.
View 7 Replies View RelatedMy EA4500 router seems to drop mine and my wife's iPhone wifi connection at what appears to be the edge of my router's range. When we come back in range, our iPhone's intermittently give the error "Unable to join network.". And we're stuck in that mode. When I check the Devices menu in the CCC interface, I notice the iPhone device is configured and still online. However the "x" box to delete the device is greyed out because it's online. So how do I get out of this state and have my iPhone connect
View 2 Replies View RelatedI have a Linksys E1000 wireless-n router. I bought the router originally so I could get my Nintendo DS on Wi-Fi. I then realized that DS games require a WEP Key, but my E1000 defaults to WPA/WPA2 mixed mode. My laptop and my Wii connect online with the default settings just fine. My 3DS also seems to be able to connect with the internet router, but not Wi-Fi, for some reason. So when I'm on Cisco connect, I go to Router settings, it brings my web browser to "http://192.168.0.1". From there I go to the Wireless tab, and then click on Wireless Security. I've tried multiple times to change the Security Mode to WEP, and even disabled security. But after I save the settings, the connection on my laptop is lost, and I have to reboot my router all over again, and am back with the default WPA/WPA2.
View 1 Replies View RelatedI just bought a new router for my home network. It is the Cisco linksys EA4500. It looks great and is rich with features but I just wish I didn't buy it!
My old wireless router started to have its wireless signal very weak, hence this new linksys router. When it is time to setup the router, I just did what was supposed to be done(which is very straight forward, just a matter of choosing pppoe and inputting a username and password) and went ahead to test the internet connection which didn't work! Upon inspection, I discovered that the lights on the internet port on the router(WAN port) didn't turn on at all as if the cable wasn't connected. I quickly checked all connections and to kill any doubt I reconnected the cable to the old router to make sure it is working and it worked. So there is nothing wrong with the cable!
I tried everything one can think of to no avail. The only conclusion one would draw from this whole scenario is that the new router is bad. So, I took it back to the shop I bought it from and before giving me another one, he said he will test it out and I said okay. Surprisingly enough, it just worked !!! Don't ask me why but it just did work beautifully, although at my house if you plug the cat6 cable(that you know for sure has internet) into its internet port, it won't even turn its lights on.
I am able to connect to the internet wireless. The wireless icon does not change. The blue dot rotates and moves about but instead of showing a connection, just the signal bars showing, it shows a land line connection with a red X over it. This happened after one of those many Windows updates.
I know I could try a reset to an earlier boot however, I made too many changes, installs and such that I don't want to loose any of it. There has to be a workaround for this lousy problem. I though of perhaps deleting my wireless connection and reinstalling it from the modem on up to the router. I just don't want to keep digging a hole! Ya know what, I really miss my apple computer which I finally gave up on because the price was overwhelming.
i have configured a cisco router with the following configuration to practice obtaining certificates from a microsoft 2008 server configured as a stand alone CA.this part works okay but what i am trying to do next is giving me a headachei am trying to delete the identity certificate but am having no luck whatsoever
interface FastEthernet0/0ip address 192.168.2.1 255.255.255.0ip nat outsideno shut
interface FastEthernet0/1ip address 192.168.1.1 255.255.255.0ip nat insideno shut
access-list 101 permit ip 192.168.1.0 0.0.0.255 192.168.5.0 0.0.0.255
access-list 102 deny ip 192.168.1.0 0.0.0.255 192.168.5.0 0.0.0.255access-list 102 permit ip 192.168.1.0 0.0.0.255 any
[code].....
i entered the following commands on the router to delete the certificatebut as you can see its telling me the certificate dosn't exist(this method of deleting the cert has come from Richard Deals complete cisco vpn configuration guide) 3Purley(config)#crypto ca certificate chain PurleyPurley(config-cert-chain)#no certificate 61E0446A000000000002% Certificate not found.ps the router is a 3640 running c3640-jk9o3s-mz.124-7.bin
On 1811W Router i have OSPF running and i do not need this static route.ip route 192.168.20.0 255.255.255.0 192.168.20.3,when i try to delete i get error ,1811w#,config t,Enter configuration commands, one per line. End with CNTL/Z.,1811w(config)#no ip route 192.168.20.0 255.255.255.0 192.168.20.3,%No matching route to delete,1811w(config)#.
View 7 Replies View RelatedI have a Linksys Wireless-G WRT54GL v1.1 with password I don´t know.I wonder how can I delete the password? I tried resetting but still asks for the password!
View 4 Replies View RelatedI moved to Comcast internet yesterday (from 3Mbps DSL), and the E4200 seems to be working well (although somewhere along the way it decided to delete all the files on the NAS drive...an issue for another day). On my laptops and wired PCs I'm now seeing 15-20Mbps down, and 4Mbps up. However, when I connect with my iPhone 3GS, I only see about 7.5Mbps down, and 4Mbps up using online speedtests. I have tried messing with the router settings and resetting all the network settings on the iPhone but nothing changes. I know my iPhone can handle more, because I get 15Mbps down when I visit family (they have a Netgear N300). I can only conclude that my E4200 is the cause.
View 6 Replies View RelatedI correct in understanding that when an external hd is connected to the e3000 via usb, that i can read and write to it, but i cannot delete files from the external drive? i have been trying to figure this out for a while and cannot delete files after i write them.
View 3 Replies View Relatedchange the network icon to the icon that shous the list of networks available with the strength bars
View 1 Replies View RelatedMy network keeps losing the lock icon that displays with the network name. I think this is happening with power shortages or outages. I have checked the settings online and it says WPA Preshared Key. Is the network still secure? I have a WRT54G wireless router.
View 1 Replies View RelatedI am using Windows 8 and my router is a Linksys E2500, in the Network folder it shows no icon and also I get a error when I right click the device and choose "Network Map" (from what I can tell this feature has been removed from Windows 8.) Both these problems are cause by an outdated Windows 7 driver on the Microsoft Update Catalog (I have Windows 8 configured to download updates/drivers automatically, that's why this installs)The reason there is no icon is because of these entries in the driver INF
[code]....
I just recently bought a linksys E900 wireless-N300 Router. I installed the software on the disc and followed the on screen instructions. When I attempt to use an ethernet cable as I did with my last router, it won't work. I get that yellow triangle icon indicating no internet access. I tried using a wireless hub to connect wirelessly...I connect, but no internet access. My PC knows its there, suggests that I reset the modem, doesn't work.
View 8 Replies View RelatedIs it normal for the "CISCO" icon/light to "fast flashing" periodically - not to be confused with the "slow flashing" that the E4200V2 displays when being "power cycled"?
View 1 Replies View RelatedI have two ACS 5.2 running as primary and secondary instances respectively. When I try to delete a remote log target under System Administration > ... > Configuration > Log Configuration > Remote Log Targets I get the following error message...."The item you trying to delete is referenced by other items. You must remove all references to this item before it can be deleted".
I have searched the configuration within the web gui and was unable to find anything that reference the object that I'm trying to delete.
I do not have an icon of any power-point document what do i do?
View 1 Replies View RelatedI've looked all over the internet for this and can't find a definate answer. Waited for live chat and got kicked before I got to talk to someone... Just sold my computer and the plan was to buy a newer mac but we've been getting along fine without a computer with just using our iphones. So my question, I see that Cisco has the Connect Express app for the iphone, and I've read about all the features it has like changing settings, router features, etc. But I can't find anything on using the app for the initial set up of the router. I'm currently on an older linksys router (set up before we sold the computer) but it's time for a needed upgrade.
View 3 Replies View Related