Some background on a scale of 1-to-10 with 10 being Sheldon Cooper and 1 being a computer less grandparent, I'm about a 6. I'm home from school for the summer and trying to access my parent's DSL by adding my router as a middleman. I tried the basic hookup (wall->modem-->router-->computer) using a Motorola MSTATEA modem and a Cisco E1000 linksys router
View 16 RepliesI hooked up with a Linksys WRT110 wireless router to a Zoom modem and my DSL on my desktop and laptop are both working fine. My problem is my phone lines quit working. I plugged a phone into the box outside and I had a dial tone. When you try to call my house it just keeps ringing.
View 1 Replies View RelatedI have 2 mbps line with D-link modem shared by 2 persons through wire. Sometime I feel that my client is using more band width than me so I want to know is there is any way I can control the speed of my client.
View 1 Replies View RelatedI received a new modem with wifi and I'm still not receiving wifi even though I've hooked it up. I think that it's not hooked up properly.
View 1 Replies View RelatedFor home use, I have a Windows Vista PC which is hooked up to the Internet via a wireless EV/DO modem that plugs into a USB port. I just bought an iPad and for connectivity, I then bought a WRT120N wireless router. But I cannot attach the EV/DO modem to the WRT120N since the EV/DO only has a USB port. I plugged the PC into one of the 4 ports of the WRT120N and the iPad sees the router, but what I would like is that it also sees the internet when the PC is online via the EV/DO modem. Is there a way to configure this? I realize that the PC would always have to be switched on if I want to have the iPad online, but for the time being I am ok with that.
View 1 Replies View RelatedI am using the WRT54G2 connected to a cable modem that requires a PPPoE login. I followed the Service Providers instructions and cloned the modems MAC address to the WRT54G and setup the PPPoE user id and password. I can then plug my PC into one of the Ethernet connections on the back of the WRT54G and everything works as expected. First I connect to the WRT54G2 and then I open a PPPoE connection in my network settings and it logs into the service provider and everything works as expected. But when I connect to the WRT5G2 wirelessly I connect to the AP fine. When I open the same PPPoE connection to the service provider it fails, the message says I have the wrong userid or password or that the protocol is not supported. Of course I know the userid and password is correct because it works when connected with Ethernet cable. I have tried disabling the security on the wireless network but that did not seem to work.The modem is a HomePNA HCNA Voice Endpoint.I am at the latest firmware 1.0.04.
View 7 Replies View RelatedMy cable tv was working great until we just hooked up the wireless internet & it went out,well basically out,its all fuzzy now w barely a picture & no sound,All the wires inside & out seem to be tight & secure,i was trying to figure this out before calling the cable company,i just cant figure it out.
View 9 Replies View RelatedSo i have 2 laptops and various phones and iPods hooked up to my network via the wireless and have 3 computers, 2 PS3s, 2 XBox 360s hooked up via LAN cable (These are not always running all at the same time). From time to time (it varies on time of day) the internet disconnects from all the computers in the house but the LAN stays connected. It will sometimes come back online if you wait anywhere from 30 seconds to half an hour at times. Manually restarting the modem by unplugging it for a while and plugging it back in sometimes works, at other times it does not. We replaced the switch and the router so far trying to eliminate them as the problem to no avail. We have not replaced the modem yet. My ipconfig info is below:
Microsoft Windows [Version 6.0.6002]
Copyright (c) 2006 Microsoft Corporation. All rights reserved.
C:UsersMike>ipconfig /all
[Code].....
I just bought a DIR-835 Router. the wireless works good-the problem however is the PC I have hooked up to the cable box, now the internet works only occasionally. I have tried disabling the firewall ,etc. The only time I can get the internet on the cable box connected PC to work is when I reset the router. I have a Gateway PC with Windows XP, I use Google Chrome. I assume it must be a Router setting that needs correcting. My previous D-Link router worked fine with the cable connected PC.
View 5 Replies View RelatedI have a BEFSR41 V2 router connected to a westell c90 modem and my provider is Bellsouth.net (AT&T). I have the modem set to PPPoE and DHCP enabled. I am using the router as a gateway. The router's status page indicates that is communicating with the modem. Release and renew works and I can detect the addresses of the modem. I just can't pull up websites. I am wondering if this router (12 years old) is not compatable with the service.
View 1 Replies View RelatedI have an RV042 Router and did a one-to-one NAT mapping for my server using an additional external IP I received from byt ISP, pointing to machine 192.168.2.5. I am now successfully able to access the machine via the external IP without issue, however the server is no longer able to ping any external IPs?
the machine has been assigned a static IP of 192.168.2.5 and static DNS servers.
I have a Netgear N router that worked fine with our old modem we recently revamped our modem to the Motorola Surfboard Extreme and it won't allow the router to connect to the internet.
View 1 Replies View RelatedI own a BEFVP41 v2.1. Under "access restrictions" I set days and time when access to internet it is allowed. Also applied "Website Blocking by URL Address" and "Website Blocking by Keyword" however some users are now getting access to the internet. I must also mention this settings: Firewall protection it is enable. Router DHCP it is disable and we use static IP address for the PC´S so I established IP range to apply the restrictions. I also try blocking with MAC address of the PC's.Everything else it has default settings. Internet wire goes first to the router and then to the LAN switch. What am I missing?
View 4 Replies View RelatedI am using the default configuration at this point. I just connected 1 computer using the default IP with DHCP on the RV042 router. 192.168.1.0/255.255.255.0.I connect my wildblue satalite modem using a static IP address 75.106.203.xxx / 255.255.252.0 I can ping the RV042 router and the static IP address of the wildblue router but I can't ping the gateway on the wildblue side. Either from the PC or the Router diag tools.
View 1 Replies View RelatedI have a problem with my Router WRT120N wen I connect to router with wireless are wired it`s not giving me Internet access but the light on the router of Internet is ON if I put the internet cable directed to my computer give me internet.
View 2 Replies View RelatedIs there any way to use the e2500 without having hard wired internet access. I would like to use with my wii fii hot spot so that I could use my old printers that are not wireless enbled
View 1 Replies View Relatedmy router and modem is working but no internet acess ive try rebooting my router but still noting change...dont know what to do...h
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:Userslito lapid>ipconfig/all
[Code]......
I have a Westell 2110 wired DSL modem for Frontier (formerly Verizon). It's not a modem that has a web interface, so I can't log into it to change any settings. It also, to my knowledge, has no bridge mode (which is a term I know very little about). I had an old D-Link WBR2310 router, and since I knew the wireless and the phones ran on the same frequency, I bought a new Linksys e1200 router. Unfortunately, when I went through the setup of the router, while I know I have a solid internet connection from the modem (I'm hard wired in as I type), and while I can connect to the router, I am unable to connect to the internet. I took down my IP address, DNS servers, subnet mask, and default gateway, and set up the router to run under a Static IP, which it does phenomenally. Unfortunately, when the ISP (via direct line or my modem) changes the IP address after a few hours, my connection drops and I have to go reset up the connection via a hard wire, taking down the information, etc. Why is this the only way I can set up my connection? What could I be doing that I'm not to get it running DHCP correctly? It worked on my WBR 2310.
View 2 Replies View RelatedI have a sonicwall firewall connected to the LAN port of the RV016 router and two DSL modems connected to the WAN ports.
Ip address allocation:
Firewall
192.168.50.9
RV016
LAN - 192.168.50.10
WAN - 192.168.60.1
WAN - 192.168.61.1
What configurations do I need to enter into the RV016 to allow other networks connected to the firewall(192.168.3.0, 192.168.2.0) to access the internet?
My desktop recently broke so i bought my first laptop. I have AT&T DSL and i bought a new D-Link DSL-2640B modem/router so i could have wireless internet. I installed it and i was able to use it with the ethernet cable, however when i tried to use wifi, it worked for only about 2 minutes before it disconnected.. Now when i try again it says that it is connected (full 5 bars) but it also says there is no internet access and i cannot use the internet.
Also, before, with the old modem i was able to just connect the ethernet cable to the laptop and just start using the internet. Now i have to connect by putting in my username and password provided by my ISP almost like if it was dial up. I don't know why i have to do this now but not before.
Tech Support Guy System Info Utility version 1.0.0.1
OS Version: Microsoft Windows 7 Home Premium , 64 bit
Processor: Intel(R) Core(TM) i3 CPU M 380 @ 2.53GHz, Intel64 Family 6 Model
[Code].....
i have an asus laptop that had a rogue virus...i brought it back to zero to the manufacturers settings...now i cant use wireless i lose connection when i take the cord out of the (phone jack looking like thingy) to my router (netgear) how do i use the wireless or find a connection?
View 1 Replies View RelatedI am trying to get wireless internet set up again and have run into a big issue. Previous wireless router was also a WRT54G and she had problems. I gave her my old one that I was no longer using, but it was still working with no problems.
The problem that I am having is that we are unable to get internet through the wireless router. We are able to get the desktop connected to the internet when we plug it directly into the DSL modem, but when we plug the wireless modem into the DSL modem and the desktop into the wireless modem, then we don't get any internet connection at all.
I had her do a factory reset on modem so that we were starting fresh. I have also tried unplugging both modems and then pluggin in the DSL and then Wireless modem, with no change. We have the ability to get into wireless settings page, but I'm not sure what in there to change that would make any difference on this one.
I know that this problem isn't actually a wireless problem, but it has to be related to the modem. We haven't even been able to get to the wireless part of the set up and we are already running into problems.
My linksys router all of a sudden stopped recognizing the 3 LAN lines that are hooked up to it, we are only able to access the internet via wireless. any suggestions on why the router would all of a sudden stop recognizing the LAN lines?
View 7 Replies View RelatedThe detected problem is the connection between my access point, router, or cable modem and the Internet is broken.The network gateway is accessible, but Windows couldn't receive network traffic from the Internet.All other devices (iPad, Xbox, android phone) have no problem connecting to the Internet.Desktop is the only one experiencing the connection issue.
View 1 Replies View RelatedMy neighbor is using my Belkin Router the basic one and has comcast. We both use his internet and have had no problems until the past 3 days. He just got the home phone service from comcast and the phone line is setup through the modem. Ever since comcast came to his apartment and set this up the home phone service to his modem the router is connected but there is no internet access. What is going on and how can I fix this. He has an HP with windows Vista and I have a Toshiba Satellite L675 that has Windows 7 Home premium edition on it.
View 1 Replies View RelatedMy laptop died last week and have been using my husbands, which I hate! We had some issues with computer freezing on some webpages or after being on webpages for awhile (like facebook). Yesterday it froze and I could not get it back on. When he got home he did scan disk (which I also did) and got it working after going into safe mode and doing system restore. He said an update had gotten through and messed things up. Anyhow, after he was on it a few hours last night, we lost connection. I figured the crazy weather was the culprit but it has been off all day. Our router is working and connecting but the adapter is not. Also our home phone says there is no line. We have unplugged everything several times, checked to make sure everything is in the right spots, I have even reset the router and rebooted the adapter. I uninstalled and restalled the adapter also. It is now telling me that "the connection between your access point, router, or cable modem and the Internet is broken". The only lights I have on the adapter are power, battery, DS and now the US light is blinking. The online and link lights are not on.
View 3 Replies View RelatedI own a Broadcom BCM5354-based wireless router (Tomato 1.27 flashed) and an Aztech DSL605E modem. When both are powered up, the wireless router sometimes doesn't get internet access because the modem automatically logs itself in. I have to plug the modem cable to my laptop, manually disconnect the modem, and plug the modem cable back to the router to fix it.
View 2 Replies View RelatedEvery day for the past week my Internet access goes down. I have a netgear router connected to Comcast modem. I have to reset the modem then the router constantly and it gets irritating. I called comcast and they say reset them. But why should I have to constantly reset.... Sometimes I just ignore it and it comes back up later... what is going on??
View 1 Replies View RelatedIs it "possible to create a WiFi" or make my desktop using hardware connection, a hotspot? (Without buying a wireless router/modem/card) I mean, is there a tweak or program I can download to configure my desktop running on Windows 7 to create wi-fi? The reason why I'm interested in this it's because, for Bluetooth, it's possible. Just wondering if they have the same nature with WiFi (In terms of configuration and tweaks)^,
View 7 Replies View RelatedI have a wired ADSL modem+router, and also a Linksys WRT54G2 V1 router. How do I connect them such that I get a working wifi available?
View 1 Replies View Relatedwas wondering if i go wired but through the router is it still being effected by the extra step or is that only going to effect wireless? asking because my wife is wireless but barely gets on, so if im about to do something intensive online would it be worth bypassing the router and plugging straight into the modem
View 2 Replies View RelatedI recently borrowed a friend's desktop and I am having issues with connecting with the router through an ethernet cable. I go to troubleshoot the problem and I get "Local Area Connection 2 doesn't have a valid IP configuration". Its nothing with the router because when I plug my laptop in with the same ethernet cable, I am able to connect perfectly.
View 19 Replies View RelatedI've been using D-Link DIR-600 wireless router for two months with my ISP, SmartBro. A week ago my internet went down due to heavy rain and technical support had a home visit yesterday to re-activate my internet connection. My net connection came back smoothly using a direct connection from modem to laptop.When I tried to connect the modem to my wifi router, the internet was not detected. Even if I reset the router settings, no internet connection was detected. Initially, I thought there is a problem with my wifi router so I connected the modem to our Edimax wired router but still it could not detect internet access. Every time I open a browser while connected to a router, this message is shown (see attached screenshot).
I tried using another ISP, Wi-Tribe with both wired and wifi routers and everything worked well. So now I assume the problem lies with my SmartBro ISP. I called the ISP hotline but they told me that they do not provide support for router connection problems; only with single, direct connect to a PC.I asked a neighbor IT technician to look into my problem but he too could not solve the problem.