My NetGear WG111v3 router no longer lights up, so I assume it's broken. Is there a way to hardwire it in through the ethernet in the NetGear modem? It tried already but when I click on the software it just beeps at me and won't open.
View 2 RepliesThe other day while I was browsing the internet all of a sudden my internet stopped working. I look down below and try to connect to the network again but it no longer shows my network anymore. I went into the room of my router and it looked fine. All lights were lit up like they should be. I turned on my Laptop to see if it was just a problem with my desktop but it's still not showing my network either.
I have restarted my router and reset it numerous times and it has still yet to show my network. It only seems to work if I connect it to my Laptop with an Ethernet cord. I have two different routers (Both Linksys) and they both do not work.I also have two different wireless adapters (D-Link & Netgear) and they both do not work
Yesterday the WLAN light stopped lighting up on my wireless router. The DSL light comes on (green), however, the WLAN light doesn't light up and the 'inetrnet' light stays on red. My laptop is saying cannot detect network, but is detecting other wireless networks in area (so not laptop prob). Did all the unplugging, turning everything off and even pressing the reset button on the back of the router but its still not working. Tried plugging in a USB cable directly from router to laptop and 'internet' light flashed green for 1 second then went back to red and still not working.
View 1 Replies View RelatedI switched my Dell Latitude D630 on yesterday morning and the WiFi light wasn't lit, and I am unable to connect to any network. I'm completely baffled why this has happened. I was using it the previous night, streaming some music on Spotify, then I turned it off as normal, and when I tried using the internet the next day...nothing. The bluetooth light is lit as normal but the WiFi light stays off, and I've tried turning the external switch on/off to no avail.
View 8 Replies View Relatedwas using windows 7 ultimate OS. last night my internet antenna was hit by lightning. later i switched on my PC and i was to browse internet, but i couldn't connect to it. i don't know whether my Ethernet port was damaged by lightning[CODE]
View 1 Replies View RelatedI had deployed Fifty 1131AG AP with Cisco 5508 Controller, the problem is some APs giving a orange ligth and some of them didn't flashing "there Led is Off"
View 8 Replies View RelatedLast evening when I turned on lights a circuit breaker was triggered. I turned it back on and it didn't trigger again. I went to sleep but when I woke up this morning and turned on my pc I noticed that I couldn't get online. I checked my router and it was dead - no lights at all. I've tried unplugging it, letting it stay unplugged, hitting reset etc... but to no avail.Lighting and the electric outlets are behind separate circuit breakers, but the only explanation I can think of is that the triggering of the cb and my 825 dying are linked. Am l looking at a dead router or is it more likely that the power adapter got fried? I don't have a fluke at my place right now due to early packing in preparation to moving away in a couple of months time so I cannot test the output voltage of the adapter right now. . Where can I get a replacement power adapter if that happens to be the culprit?
View 1 Replies View RelatedUsually when i go to type ipconfig - under IPV4 - i get the internal IP address of my PC. which is usually 192.168.X.X But today, I get, what looks like an external IP, when i type "ipconfig". I get 89.X.X....
View 11 Replies View RelatedI have been using my wireless (linksys) for years now and just recently my wifi network no longer shows up on any of my devices (laptop, phone, etc). I am able to hard wire into the linksys and my laptop works but when I try to connect wirelessly, I can't even see the wireless network, I am only able to see my neighbors.
View 2 Replies View RelatedI was using desktop computer and got infamous blue screen of death Rebooted and everything was fine except could no longer could see LAN connection or connect to internet The desktop computer also has a wireless card that allows me to connect to router wirelessly but only get "connect with limited access" I have a cable connection through a router and tried connection dsl directly to ethernet and bypassing router but no change Router works for other laptops to connect wirelessly I can see both network adapters in the device manager and both say devices are working properly Here are the results of ipconfig /all:
Microsoft Windows [Version 6.0.6002]
Copyright (c) 2006 Microsoft Corporation. All rights reserved.
C:UsersCooper>cd c:
c:>ipconfig /all
Windows IP Configuration[code]......
I work next to someone who has been complaining constantly about how his computer will give him some kind of "Access is Denied" error on one of his network drives almost every time he uses it. Other network drives on the same server work. Because it can be fixed by rebooting, the IT person has filed it as low priority / given up on fixing it but I would really like to shut him up but I can't find the answer in google. His computer is Windows 2000 SP4 and the server is Windows NT 4.0.
Edit: It happened again and I was able to get the actual error message. "H:DIST is not accessible The specified network name is no longer available"
I just upgraded by Netgear router to the Netgear n600. I can no longer print to my Dell 926 All in One. I tried following the "Setting Up Your Printer" Instructions specifically steps 11 to 12 C but I receive an error message stating that the printer adapter was not able to join my network.
View 7 Replies View RelatedI have recently bought a new computer and have been happily connected to my wireless network for three months. The other day the connection was lost and now I cannot connect to my wireless or parents wireless networks. I can connect via the ethernet only. I will attatch an ipconfig for you to have a look at when I am not connected can see my wireless network connections however when I tempt to connect it says windows cannot manage it. I am running windows 7 home premium 64 bit[CODE]
View 2 Replies View RelatedA couple weeks ago my HP laptop stopped working. It would not boot and I had to put in the recovery discs to get it working again. Before this the laptop had connected fine to my home wifi secured with WPA2-PSK[AES]. After this problem tho it refuses to connect while it is secured. When not secure it functions fine and I am currently using it to type this post. I would have no problem continuing to use the wifi unsecured but another member of my household works with confidential medical information from home and is worried about the lack of security. I have attempted the trouble shooting tips on the support website already. My computer model is HP G60-235DX and the router is a Netgear N300 model WNR2000v3[CODE]
View 4 Replies View RelatedI have never had to do anything to connect to my fathers netgear router or my own netgear router. I would just turn on my pc and have internet. After my brother touched my computer it no longer recognizes any wireless connection. My internet provider says that I need a new router. I don't think that is the problem because after my brother played with my computer it was unable to see any connections (not even neighbors which I normally see). This makes me think something is wrong with my computer not the router.
PS. I do have my wireless switch turned to on. My brother doesn't know what he did but will not be allowed to play with it again.
Basically, I rebuilt my network over the weekend, to include a subnet, and can no longer connect my desktop to the remote PC. My old router was reset to defaults and re-configured. My PC has been wiped, reinstalled, and fully updated.The error I receive is "Remote Desktop can't connect to the remote computer for one of these reasons: etc" I've only seen this error in the past when the PC I connect to was powered down. I have confirmed that everything is still set up properly on the PC I'm trying to connect to via an associate, and it is not powered down.
Old setup:
[My Win7 PC] ---- [old router] ---- [modem] --- [internet] ---- [Remote PC (Win 7)]
...............................| | |
.........................other local PCs
New setup:
[My Win7 PC] ---- [old router] ---- [new router] ---- [modem] --- [internet] ---- [Remote PC (Win 7)]
.........................................................| | |
...................................................other local PCs
1. I went into Windows firewall to allow Remote Desktop through, but it looks like that only needs to be set for the PC I'm trying to connect to. (Yes/No?)
2. I've forwarded port 3389 from the old router to my PC.
3. I haven't done anything yet to the new router, because I really can't tell if I'm doing the right things. The very first time I connected to the remote PC, it went right through, and I didn't have to change anything in the old router (I think - it's been awhile). I really don't know where to go from here, and it looks like the setup options I've found in the forum so far (static IP, port forwarding, Windows firewall changes, etc.) leave me with more security risks than I had on the old network, and there seem to be some conflicting opinions about the setup process.
A business network has had a Static IP Address for several years. Recently, something caused the settings to be changed to "Obtain an IP Address Automatically". As a result, pcAnywhere will no longer connect, and this is a critical function of the office. This has to get fixed. I've attempted to put the settings back to what they were (The IP Address, Subnet Mask, Default Gateway, etc...) but now the Server will no longer connect to the internet when you setup the Static IP. The settings I am using are exactly the same as the ones from over 2 years ago. Now they no longer work, and networking is confusing to me.
View 4 Replies View RelatedMy Internet surveillance stopped working
View 1 Replies View RelatedHow to solve this error in between windows 7(Host) & Windows server 2003(Guest).
View 2 Replies View RelatedA bunch of stuff from my laptop was restarted and uninstalled. Now my laptop doesn't even pick up a signal
View 1 Replies View RelatedThe other day, I shut down my laptop and when I turned it back on, it would not connect to the internet. It continuously says limited connectivity and unidentified network. my info is listed below
Location: Birmingham, Alabama, United States
ISP: AT&T they also provided the router/modem which is all connected in one.
Router Model: 2wire Gateway 3800 HGV-B
Connection Type: Wired and Wireless
Wireless Encryption: TKIP
Network Card: Dell Wireless 1510 Wireless-N WLAN Mini-Card
Computer Model: Dell Studio 1535
OS: Windows Vista Home Premium SP2
IP configuration brought up this info. Also tried pinging Google.
Windows IP Configuration
Host Name . . . . . . . . . . . . : Stephanie-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Broadcast
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No[code]......
Why is it that the dhcp on my router is no longer able to give out ips or rather it assign them as for as it concerned as it will list say 199.170.0.102 but the device will have none or make up one for it's self and never get the ip that the routers dhcp gave it this happens on all devices. I know power cycling will fix it temporally but usually it will start doing it again in a few hours also I know that I can use a static ip this was my way around this problem but I have one device that won't use nothing but dhcp a printer. I had an old linksys router that did this and I figured it's old it's slow time for a new one after a few months it started, some computers are on the fringe of being able to get a signal but are still fair also even with static ips they sometime stop connecting and we have to disable the connection then reconnect to fix it the router is a dlink 615 dual band set to only G/B because 1 most devices only g 2 the one computer that has a wireless n is 70 ft away and works better with g.
View 13 Replies View RelatedLast night on the xbox 360 i was suddenly experiencing alot of lag on other peoples voices. i took no notice of it and the next day i went on my laptop and alot of websites wouldn't load properly.i can go on google,obviously this and my hotmail(after having to wait a long time for the hotmail to load), but others such as ebay will not load. I cannot even access my router settings by typing in my ip address, instead i get a message saying the page cannot be found. also i was disconnected from xbox live with the internet to xbox live part not working. Obviously the first thing i done was turn the router off and back on but it hasn't made any difference.
OS Version: Microsoft Windows Vista Home Premium , Service Pack 2, 64 bit
Processor: Pentium(R) Dual-Core CPU T4200 @ 2.00GHz, Intel64 Family 6 Model 23 Stepping 10
Processor Count: 2
RAM: 4055 Mb
Graphics Card: Mobile Intel(R) 4 Series Express Chipset Family, 1804 Mb
Hard Drives: C: Total - 290204 MB, Free - 141170 MB; E: Total - 14999 MB, Free - 5644 MB;
Motherboard: Dell Inc., 0G848F, , .5MDJWJ1.CN7016697U05OT.
Antivirus: AVG Anti-Virus Free Edition 2011, Updated and Enabled
My internet has been very sluggish so after reading the thread about Router security and neighbors who might be stealing my internet connection via WIFI, I decided to check what kind of security I had. Turns out I have WPA and no unknown devices were connected at that time. Would like to get an email whenever a NEW device logs in...if that is possible. But while I was in there "futzing around" I did something terribly wrong. I followed all of these steps. Then I noticed that the router speed section had me listed at 145mbps. I had recently changed cable companies to one that provided faster interenet. So I figured I would bump that up to 300 mbps. I can no longer access any of my router settings. What did I do, and how can I undo it?
View 4 Replies View RelatedSince sometime on 10/7/12, I can no longer access the internet from my desktop.I'm connected via wired Ethernet but have also tried connecting via a USB WiFi Modem.Network and Sharing Center shows "Unidentified Network No network Access".All other machines on my home network have internet access (one other desktop as well as multiple WiFi clients).I've tried pinging the router (192.168.1.1) .. request times out.I've tried reset TCPIP and Winsock Stacks, Disabling / Reenabling the NIC with no effect.In troubleshooting, I've found a registry entry which seems to be different from that in my working desktop and which I cannot change.It's HKLMSYSTEMCurrentControlSetservicesTcpipParameters. [code]
View 11 Replies View RelatedHad my DIR 615 rev A just fail one day spontaneously; managed to bring it back by reflashing from the emergency room, but now it will not hold setting through a power cycle, other than this it seems to be working well.
View 9 Replies View RelatedMy DIR-655 has been working flawlessly for several months since I bought it. It is connected to Road Runner High Speed Internet from Time Warner. This morning it will not access the Internet. It shows a wireless connection, and I can connect to it via direct wired connection, but no Internet. A direct connection to the Time Warner Cable Modem connects to the Internet just fine. Cycled power on all units, & Time Warner reset the modem. Nothing has fixed the Router.
View 14 Replies View RelatedI an aware the SR520 is no longer made, But we use the VPN Remote aspect of it (For site to site UC540 installs), is there anything else that has the same VPN functionality, and what would i be looking for in regards to terms for the client to be on the router itself?
View 0 Replies View RelatedAfter upgrading to 7.2 on my 5508 WCS, the 1310 APs will no longer join. After a call to TAC they said the 1300 and 1400 APs are no longer supported on WCS. Is there any plan to add them back as supported in future releases?I was thinking I could downgrade my backup 5508 and change the APs to autonomous. Or is there some easier way to make them autonomous?
Also, as a low cost outdoor AP, I guess I am reduced to putting 1262s in a NEMA box with outdoor antennas. The 1552s are way too expensive for the quantity I need. Is there some other inexpensive outdoor AP that will replace 1300-1400 series?
Just purchased a 3355 and installed, followed the set up no problems, added to WCS. Then WCS says no longer able to be reached.
Unable to ping, have to keep running the setup./opt/mse/setup/setup.sh seems, like the settings are not being kept.
Tried /opt/mse/setup/setup.log and sasys I have no permission, this is when logged in as root.
I was trying to learn a bit more about routers and therefore tried to acces one of our routers using an external ADSL line at work.The router is a ZYxel Prestige 324. Since I did not have the password I performed a hard reset.Now when I try to acces any website I receive error 105 ERR_ NAME_ NOT_RESOLVEDThe only difference that I can see now is that there is no longer a connection specific DNS suffix assigned.Could this be the issue? If yes how can I configure this?
View 3 Replies View RelatedThere are 2 locations to choose from. One location requires me to run longer CAT6 cables. 7 of them. The other location requires me to run a longer RG6 cable. (the CAT6 runs would then be about the shortest they could get)So, I guess I need to know which can handle running parallel with power cables better, 25feet of RG6 or CAT6?The parallel with power cable is only for about 6-8 feet, but that's already more than it should be for CAT6.
View 4 Replies View RelatedI have a windows 7 computer and a windows 2000 on a wired network. The windows 7 and 2000 previously played nicely although it was a bit of a pain to get it to work the first time, don't really remember what the issue was. I have a big old CAD plotter connected to a parallel port on the windows 2000 computer and previously was able to use it from the windows 7 computer. I was also able to access any file on the windows 2000 from windows 7, it all worked fine a few months ago. I haven't had the win 2000 computer on for a while but recently needed to use the plotter. I now get a log-on error when trying to access the win 2000 from the win 7, but it shows up on networks. The log-on error window shows a domain with the name of the windows 7 computer listed as the domain name, but nothing is set to be on a domain. I can access the files on the windows 7 computer from the win 2000 computer with no issues in that direction. There is no home group set up (think that was the issue the first time) Windows 7 is always updating itself and I suspect that's part of the problem, I am guessing something went back to a default during an up-date but I can't find it.
View 3 Replies View Related