I'm having problems with the networking here, Im not Admin But since it only effects me no one else is bothered.The problem is; that I do not show up on the router, or my Mac address, and port checkers say every port is shut for me (yet i'm here). Noticed this once ports I opened (and were working fine for weeks) suddenly stopped working, Went to check the problem and I wasn't there. But when i unplug myself from the router and plug it back in, they work on "Test Drive 2" (shows if ports are opened or closed on the launcher) but show they're closed on a port checker and a few minutes later the launcher then says they are shut.
my computer is a dell dimension 1100, with a Linksys WMP54G wifi card, running vista home basic.In the wifi thing in the notification area, it shows two wireless networks, One is my normal SSID (Lower Net), and one is "Unidentified network". They are both on one wireless connection (Wireless Network Connection 3). When i try to go on the internet, it says i'm not connected. i tried disconnecting from the unidentified network, but that disconnects me from lower net too.
Some background first. Last night I went trolling around for a solution to an ip address conflict message I receive when I try to go onto Xbox live via a network bridge on my laptop. What I eventually ended up doing was going into my tp-link wireless router settings (not sure of the exact model number as I am not home right now) and reserving two different ip addresses for my laptop and my Xbox using their MAC addresses. It didn't appear to do anything ( now I think possibly because my Xbox needs the same ip as my laptop?). Anyways I tried to go onto Xbox live and it worked at the start (as it always does) and then 30 minutes in, the ip address conflict message came up (usually meaning a disconnect from Xbox live is imminent). But I actually ended up staying online for another 3 hours until the Internet crashed.
Upon further investigation I noticed that my wireless network was not even showing up on my computer, my phone, or any of my roommates computers. I went upstairs to check the wireless router and it was seemingly working correctly (i.e. no flashing lights or anything). Not quite sure what to do. I would go back and change the router settings but I don't think I can without a connection to it.
I've noticed in the mornings lately when I get up around 6 am my internet will not work. Not on wireless or on my desktop. I decided I'd log into the router to see if there was a firmware update or anything. I had checked the logs and there are quite a few entries relating to DoS. I googled around and saw that it could be some sort of packet loss and the router is mistaking it for some sort of DoS attack. And that due to it not showing up multiple times every second it likely isn't a DoS attack. Here is a few from the logs:
I am trying to configure access control rules, but the list of computers (ip addresses and mac addresses) are empty, I have setup all of my devices with static ip's, they are all turned on and all have internet access. None of the systems including the one I am trying to configure the rules with are there, They don't show up in port forwarding either. Any one ever have this problem? I returned and DIR-825 Rev.b for this same problem because i thought it was defective.
I have tried rebooting the router, rebooting each pc and trying different ports on the router itself. There are wireless and wired computers that I am trying to setup but none of them show up. When I try to manually enter them into access control ie. 192.168.0.103 it will only allow me to put one computer in for each rule.
The old rev.A router this one replaced work perfectly fine with the same cables and computers setup the same way.
Cisco E1000 router.connecting directly to the router, internet works. When connecting wirelessly, it works for about 2 minutes, then I get no connection and a yellow ! in the connection setting icon. No wireless internet will work until I power down and restart the router. Then the same problem continues.Today when trying it, it won't even connect for a few minutes. It shows as "connected" on my laptop but it has the yellow ! and will not access the internet. So I am no longer ever able to connect wirelessly. I've done a hard reset already.
every now and then my Belkin brand router will just switch from green light, to red light. Sometimes unplugging it for a while fixes it, sometimes unplugging it for a LONG while fixes it, sometimes prayer and chanting fixes it. But most of the time the red light sits there mocking my efforts.What's making this happen? Is it my wireless security settings? Because I used to try and fix it by pressing/holding down the WPS button.
Region : Australia Model : TL-WR702N Hardware Version : V1 Firmware Version : ISP :
I am posting this in the wrong place but thats only because I cant find the forum for the TL-WR642G ver 3.6 device.Basically I am unable to see any QOS configuration and I wanted to know if this is available to this model ?I know the ver 4.0 firmware update states that QOS is added but can I update a 3.6 device using a ver 4.0 firmware ?
I'm using the EA4500 router with Cisco Cloud Connect. I've noticed under Devices I'll see devices named "Network Device". They have a generic MAC address with something like "00:00:00:00:2F". They will have an IP that's already assigned to another device.
my cisco 2611 series router is showing garbage value at start up and not allowing me to enter in Romon mode I check the bitrate in console .it is 9600/8N till then i am unable to start the router Can you tell me how to change configuration register value without entering in rommon mode
i have Cisco 2611 series router it is showing garbage value while start up as 00000000000000000000000200000000000000 and i am unable to log in it Roman mode.
I have had a heck of a time getting this server up and running and it looks like I finally have it, except for one thing. Everything works except for the vpn. I do not have the vpn portion on the router configured since the SBS server will be acting as the vpn host, but maybe I need to configure the vpn elements on this router for it to allow vpn connections in?The other thing that is "off" as the title of this post indicates is that the server is not showing up on the router's attached devices under the correct name. It's showing as some generic WIN-****** nameI am doing this project for a non-profit without compensation and the networking part of it has been a nightmare. So any solution that doesn't entail me reconfiguring the server. Everything else appears to be functioning properly, dhcp, dns, ingoing, outgoing mail and the web interface.
i was looking at my network settings today on my pc and noticed a router (linksys wrt160nv2) that wasn't mine. i can right click on it and see its mac address but when i double click it asks me for a pin number. the device shows up with both a wired and wireless connection. i'm using windows 7 64-bit.
When I'm in Setup -> Basic Setup -> click on DHCP Reservation, I don't see all entries I've created earlier but computers that connect still have the correct IP address on the network; I don't know if I can create additional entries if nothing appears
When I go to Status -> Local Network -> DHCP Client Table the list is blank but some computers are connected to the networkI'm using firmware 1.0.01 build 10 Feb 21, 2011, language = English, Firefox 4.0.1.Rebooting the router doesn't change anything, I can't see connected LAN equipment and DHCP Reservation is empty despite the fact I've created entries.Together with the "Access Restriction" which doesn't allow to block a computer from 10pm => 8am unless you create 2 rules + various issues with attached USB + 2.4Ghz signal that is far from optimal (never able to achieve more than 144-N-Mbps) and I ask myself if I will not contact the store where I purchased this unit and ask a refund (and buy something else from another brand...)
I have an EA4500 and am using Cisco Connect Cloud software. Its working mostly fine except that I have one device on the network that will not show up in the device list. This is not an issue in itself and normally I would ignore (although it used to show up when I forst got the router) however..
The device is a WDTVLive media unit and required access to windows shares on a media server. Now the WDTVLive device is server an ip address by the router and is available from everywhere on my network but every couple of days it loses the capacity to search windows shares.
I know what you are thinking and I initially thought the same, this is an issue with the WDTVLive box. However one day I spent a few hours trying to resolve (Am an IT Consultant and know a little about networks) and found that I could not fix the issue. I then rebooted the router and it started working. I have since confirmed that every time it breaks I have to reboot the router.
My router usb storege was working fine with my old videos and streaming fine too but now im putting some new videos on the usb storage my router its not showing the new videos on the usb storage.
Why is my WRT54g router only showing the 1st LED port is lit, and not the rest when I have changed or added a device to the 2nd,3rd,4th port? It is also stopping my ability to stream,view youtube etc. When I disconnect the router from my cable provided modem, everything works fine?
All the documentation for this router shows the Access Restriction tab in the router configuration menu. It's the same as other linksys routers. The current version of the firmware doesn't have this functionality. Was it removed?
I have a Linksys model WRT54GS2 with 4 ports, with Ethernet cables connected to ports 1 and 2. I have a laptop connected by wireless connection, with only an Xbox connected using Port 1 and occasionally port 2. Just recently, port 1 shows no activity. When connected to Xbox it doesn't display a check mark showing connection but does with port 2. I've connected it to port 3 and 4, which shows a check mark but won't connect to Xbox live. It's like port 2 only works, what I can do to "fix" ports 1, 3, and 4?
Had a secure network with my model wrt54g2 v1 router, then suddenly it's not showing up. All I have is a unsecured Linksys way on to the Internet. How can I get this back to my secure network?
We have Cisco 2851 Router part code CISCO2851-SEC/K9 facing issue while set peer configuration, issue description below.
Issue:We are facing the problem while configuring set peer as when we try to this we face error like 'unable to set peer.maximum numbwe of peer (40)exceeded'
We suspected the IOS issue hence we have gone for IOS upgrade for this Router but this error is still coming while configuring set peer.
Previous IOS: c2800nm-advsecurityk9-mz.124-15.T7.bin New IOS:c2800nm-advsecurityk9-mz.124-24.T7.bin
We are attaching here the snap shot of error that is coming while configuring the Router with set peer command along with show tech of the Router to understand this case brief.
We have a Cisco 2801 router running IOS "c2801-spservicesk9-mz.151-4.M4.bin" which we upgraded from previous “c2801-spservicesk9-mz.124-3d.bin”.
Requirement.
We want to monitor the device temperature via snmp but unable to do because temperature ratings are not available on "show environment all" output like below.
Routeri# sh environment all Fan 1 OK Fan 2 OK ILP Power Supply - Absent Fan Speed Setting: Normal
Where as on Cisco 2811/51 & Cisco 3825/45 we can get temperature ratings on "show env all" output.
As per link [URL] below commands are supported on Cisco 2800 series router.
Command options • show environment all • show environment fans • show environment leds • show environment power-supply • show environment table • show environment temperatures • show environment voltages
I want to know whether this is Cisco 2801 platform limitations or something else. tried to find Cisco doc on this but no luck.
Region : UnitedStates Model : TL-WR841N Hardware Version : Not Clear Firmware Version : 3.12.5 Build 100929 ISP :
I have the WR841N v6/v7 Firmware 3.12.5 Build 100929
The router stops showing up after 30 minutes to 1 hour. If I switch it off and on , it starts working normally but again suddenly stops and cannot be detected after 30 mts- 1 hour.
My wireless connection for my laptop is showing upas N on Win 7 but G on DIR-655 status page??? I'm confused. Am I getting N speeds/coverage or stuck with G. If G, why? I've tried wiping my wireless network config. on Windows and reestablishing it, but no change. The DIR-655 config page shows my machine connected at 54 Mbps and Type as G
I have linksys E4500 and I would like to be able to see the website visited vs ip address.Is there a way to enable same or achive same via parental controls.Again I do not want to block a website but monitor which websites are visited. Is this achievable via router or an additional software/hardware required to be used with router
I have purchased E2500 and i am having following problems:
1. DHCP client list not showing - only shows when i reboot the router. After some time, the list never shows even when i press refresh button 2. I can only reserve IP when i reboot the router - after some time i cannot do this action also
I have upgraded to latest firmware and also peformed reset as directed by support.
Experienced problems with guest network not showing up as an available network on a device (laptop, iPad, etc)?I double checked if guest network is enabled on a EA3500 router. What other steps can I take?
I have the WRT400N router with the latest firmware. Recently I have noticed a device in my DHCP that I do not recognize. It is not device I own (believe me, I have racked my brain and confirmed) as it shows as an Acer pc. I cannot ping the IP address however. I have rebooted my router several times thinking maybe it's a former connected device but saved in memory but it keeps coming back. I am thinking possibly it is someone hi-jacking my Internet, but not sure. I am using WEP security but it shows a LAN connection which is strange for a wireless device. The only hard wired pc is my HP.
I just purchased an E4200 router. I have four clients on my network and they are all set up for DHCP. I renewed their IPs and they all are connected. "Cisco Connect" reports that I have four clients connected. When I access the router and bring up the DHCP Client Table, there are no entries. There should be four entries. Aftern I enable the logging function, none of the logs have any data in them even after I wait for 45 minutes and use the internet and renew IPs. I am using Firmware Version: 1.0.03. I have the same results for both Chrome and Firefox. I want to be able to set Static IPs but I am hampered by the not having any clients in the DHCP client table.
