I am using Wireless DSL Router which connect through Modem..It shows the internet connection but cannot access through wireless even my Laptop is connect to router thru Wireless...Previously it was connected to internet through same router. Its work with direct LAN Connection if directly connect with MODEM. But after formating my laptop its connect to Router but can't get access to internet. I am using XP OS.
View 3 RepliesI have two SSIDs on an Autonomous Access Point, that goes to a 2960 switch, that connects to a L3 3560. I have a vlan for admin/private internal access that uses the native vlan (1) and guest vlan (50). I have configured both and I am trying to get both to go out the same Internet connection.
I cannot get the guest access to access the Internet. It looks like my computer will go, but it just comes up saying no Internet access.All interfaces are trunking this vlan properly. I can communicate from the laptop to the 3560 but I just can't get to the Internet.
I have a Sony Vaio running Windows 7 Home Premium. Yesterday I accessed the Internet at the office over a Cat5 cable. Last night I accessed the Internet at home via my USB Internet dongle (actually an O2 mobile phone). Today neither works. I have also tried to connect to the Internet via Wireless and that does not work either.Needless to say my desktop (using the same Cat5 cable) works. My mobile phone can access the Internet on it own. And others can get the wireless to work.My Vaio can connect to all three; however, all three say "No Internet access".I changed nothing between last night and this morning. I have scanned through the list of Windows Updates and nothing has been downloaded in the past week. I have turned off my firewalls (in both McAfee and Symantec Endpoint Protection). I have run the three NETSH reset commands with Administrator privileges. I have rebooted my machine numerous times. Nothing works.
View 4 Replies View Relatedwireless internet connection connected no bit it says no internet access what is the problem
View 1 Replies View Relatedi would like to know that how to stop internet access through network complete internet access
View 2 Replies View RelatedI rebooted my modem and now I have not internet access on my wireless connection. The internet works fine on my 3 computers I have connected to cables and my wireless devises have a good wifi signal, but no internet access.
View 3 Replies View RelatedI'm not sure why I have a broadband connection AND a local area connection, but I cannot connect to the local area connection whereas the broadband connection is fine. I've already set to obtain IP address automatically and still not enabled. The wireless connection was working fine a few days ago, and seems to have been reset by the ISP causing these issues. Other devices are also unable to get internet though they can detect and connect to the router. Here is my ipconfig/all. Note: I am in China so my settings are possibly different than what you're used to.
[code]...
About a month ago i was able to create ad hoc wireless network to connect my iPod to wifi. And then not to long ago, i had some kind of virus problem which caused me to get Norton 2012. But now when i try and create a wirless network it says that there is no internet access. But i use my laptops internet with a yellow wire connecting from my laptop to my modem. And the interent works perfectly fine. So i do not know why my interent wont allow me to use a wirless network.
View 1 Replies View Relatedlaptop with window vista/home edition.Cannot access wireless internet connection (WIFI) from laptop. Installed Netgear G-router onto desktop.
View 19 Replies View RelatedA week ago this laptop was working fine. However, now it will not connect via wireless to the internet. It says that it connects to the router but not the internet. I can connect to the internet if I use the wired LAN connection. I tried a restore to two weeks ago (when it was working) and it did not solve the problem. I do see in the wireless network connection status that IPv4 connectivity = local and IPv6 connectivity = local. While on another laptop (that is working and connects to the same wireless router) the IPv4 = internet and IPv6 = no network access. I think this may be the issue, but am unable to find out how to change them.
OS = MS Vista Home SP2.
My home network uses a Cisco router connected to a cable modem. The router has a WAP and a second WAP is connected with power over Ethernet connection. Both WAP have strong signals. We have PC's, a Mac and several Iphones connected wirelessly. When using the Internet, the computers and phones seem to stall when moving from one web page to another. This happens with one or several devices in use, so it does not appear to be related to volume. Re-booting the modem and router usually corrects the problem, but not always.
View 1 Replies View RelatedI own a desktop hp pavilion windows xp that i recently reset to factory settings and now I'm having trouble getting wifi. The other computers in my house work fine with the router, and my computer gets internet through an ethernet cable, so I know it isn't the router. I used to use a d-link G rangebooster desktop adapter to get wifi, and I have tried downloading a driver for it but still no luck. Some of the things I have tried are as follows:
-Renewing IP address
-going through new wireless network wizard
-unchecking the "IEEE 802.1x authentication"
-creating a new network for the "preferred network list"
-other random edits that have not worked!
The wireless network connection says signal strength is excellent but status is limited or no connectivity.
I recently had a virus which I believe I successfully removed (virus scans show no threats) but now I am unable to connect to the internet. My computer shows I am connected but IE displays error message 12007 and Mozilla says "server can't be found." I am running Windows XP SP3
View 1 Replies View RelatedMy husband has an Acer Aspire 5720-4126. Last month I bought a Netgear wireless router (model WNDR4500) and he is the only one in the house that can't connect to the internet. He is able to get to the router, excellent strength, but the Activity has Bytes: Sent-3,142 Received-0. I had the Netgear customer service tech try with no results. [code]
View 7 Replies View RelatedI was installing a software on my other laptop (it had SQL software with it) and I ran into some trouble as I got error problems that the installation of the software had failed and now whatever I do, I can't access the web! Sure enough, my wireless connection connects successfully and it indicates that I am on the "Internet" but every time I try to use either firefox or internet explorer to go to a web site, it says I don't have a connection. It is extremely odd and I don't know what it might be
View 6 Replies View RelatedI have a DIR 655 connected to cable DSL modem RCA DHG534. I can connect to the internet through the Ethernet cable ports, but i can't access the internet via the wireless. The SSID will show up on the wireless computer(s) and Ad's. Under Control Panel, Network Connections, Internet Gateway is shown as disabled.
View 1 Replies View Relatedhave a Cisco 5508 controller (version 6.0.199.4) that when I enable global multicast mode it will work for an hour or two and then it will kill the network. All internet both wired and wireless, access to server everything dead. I then have to directly connect to the service port and disable the global multicast mode. Then two reasons for enabling it are Docs2Go and LanSchool both require multicast to be enabled. I have it enabled on our wired network and it works OK there. ted.
View 10 Replies View RelatedI have one WET200 Wireless Brigde, connected to internet router... I can't use the infraestructure mode to broadcast the ssid to wireless cliente like laptops,
Only can use the ad hoc mode, but the wireless clients dont reach the internet from adhoc connection trought WET200...The datasheet saids "client only" for WET200, what is the diference between client only and Access Point mode? ??
I'm looking at doing an intranet project at work. What i want is to have one main machine that will have a forum and website on (probably Windows IIS on Windows 7). Then i want to have approximately 10 other users on laptops that can connect to my intranet forum and site via "wireless" connection, but at the same time none of those 10 laptops or my main machine having any "internet" access. Is this possible and if so how
View 5 Replies View RelatedAt first, it says "limited or no connectivity" and after reading possible solutions, it now says connected and has a very good signal but once I open Mozilla or Google Chrome, there's no internet connection. The icon doesn't also have that blue light that I think is an indication that it has internet connection. My roommate can connect to this wifi with no problems, her notebook is Acer, just like mine. We also have a wifi at home and it connects smoothly. I don't why I'm having problems with this aztech wifi here. Btw, I do not own this wifi or router. It's like an open network.
View 1 Replies View RelatedI have an Asus Windows 7 laptop with an Atheros AR9285 Wireless Network Adapter. I am trying to access a student communal network (IT support is sadly none-existent) which means I cannot perform tests on the router, but can confirm that my girlfriend can connect with a Macbook in the same room as me, and that other Windows users can too in other areas. I can connect via ethernet into the wall (although not 100% sure this is the exactly the same network) and I can connect to other unrelated wireless networks with no problem. Up until a couple of days ago I was able to connect, but have not done any windows updates that might have changed my settings. When attempting to connect my computer tells me (often, not always) I have "Internet access" under "IPv4 Connectivity", but the browser does nothing (or, sometimes, will struggle and load one webpage, only to fade into uselessness again immediately afterwards - very much a tease of a connection).
1) Disabled various firewalls/antivirus [Microsoft Security Essentials, Windows Firewall, AVG] (perhaps worth saying I have never had Nortons, McAfee or any other anti-virus installed on this laptop)
2) Reset Network Adaptor using Windows Diagnostics Tool.
3) Updated the driver by searching automatically for drivers in Device Manager.
4) Removed and Renewed the Network in "manage wireless network".
5) In Wireless Connection Properties > Internet Protocol Version 4 (TCP/IPv4) made sure both Ip address and DNS address are set to "obtain automatically" [nb: Internet Protocol Version 6 has the same settings)
6) WIthout remotely understanding what I am doing have typed the following into CMD in this order: ipconfig/release,ipconfig/flushdns, ipconfig/renew [for the latter this message is given "An error occurred while renewing interface Wireless Network Connection: unable to contact your DHCP server. Request has timed out."Beyond that, I'm basically out of ideas. Something is clearly not quite right, and yet I can connect wireless to other networks (my mobile phone on 3g emitting a dodgy wireless signal no less).
Here is the ipconfig/all information [being security conscious and ignorant, I have blanked out the ip, and the final bits of the physical address, as well as the connection specific DNS suffix]
Windows IP Configuration
Host Name . . . . . . . . . . . . : XXX
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
[code]....
If I ping [URL] it either says [currently unable to recreate this] "Unable to reach destination server" for all attempts, or, as currently "ping request could not find host [URL] I notice that it says in Ipconfig/all that DCHP is not enabled. I am sure this was not the case before, when the problem did not exist. When I connect to other wifi networks DCHP is enabled. I have double-checked wireless properties are set to obtain IP address and DNS address automatically. They are at all times (and I have rebooted) - no change to ipconfig/all.
my primary source of internet at my house for the passed year is an at&t 3g usb modem (sierra wireless lightning), becuase i live in the middle of nowhere (only other option is satellite). Up until now i've been using a wireless ad hoc network to share the connection with multiple computers. I just purchased a cradlepoint router that is compatible with my usb modem so I can have a "real" wireless network in my house. I set it up yesterday and so far its working great, I have a wii streaming netflix, an android tablet, an iphone and two laptops (running vista, and win7 respectively) currently connected. The problem is my 3rd laptop, also win7. It is my primary computer that I use for business and absolutely essential that its connected to the internet. It (seems) to connect to the wireless network just fine, but gives me a "no internet access" error.
This laptop will connect to other wireless networks: it always connected to the ad-hoc, it will connect to my wifi at work and the network at my boyfriends house, also i just tried it with the verizon 3g mobile hotspot app on my droid and it connected right away. It also works just fine with a wired connection to this router (ethernet). I'm not sure where to start since every other device in my house is working with this network and this laptop will connect to other wireless networks.
ps/ Going through the windows onscreen troubleshooter it will either tell me "there is a problem with your broadband modem" or "There is a problem communicating with DNS server" (but it wont fix it)... and after going through endless google searches, i've done everything thats been suggested so far (making sure dhcp is enabled, powercycling the router/modem, updating drivers, ipconfig release/renew, disabling the firewall).
i just hooked up a dlink router at home so i can use my laptop in different rooms. i have a desktop in one room and the internet works fine but when i hooked up the wireless router i can connect to the network but it says no internet access so i cannot get online my brother in law is really good with computers and i called him and tryed doing a bunch of different things like changing the web address and such but nothing will work.
View 4 Replies View RelatedBasically both the wireless connection and LAN connection in my house were working fine until a couple of days ago. I got one of those viruses that redirects all the links that you go on to random websites on the main PC. I ran a full scan with McAfee Antivirus Plus and it came up with nothing. My brother suggested i try downloading malwarebytes on my laptop and installing it on the PC to get rid of it. Malwarebytes picked up the virus and got rid of it. I restarted the computer and when i tried to access the internet on the PC the message on the browser says "Could not connect". My wireless is fine, but the wired connection to the PC is not. When i look at it on the PC it says that it is connected but the browsers show no connection.
View 1 Replies View RelatedI have had my HP laptop for 2.5 years now, originally bought with Vista 64 bit. It now has Windows 7. Up until now, internet access and connectivity have been working fine. But, all of the sudden today, I couldn't get Internet Access despite trying both an ethernet port and a wireless connection (connectivity was working.) I know it's something with the laptop, because my ASUS netbook has no problem accessing the internet. I've tried looking around at some of these tech support sites and haven't really found anything that's worked for me. I've tried using CCleaner to remove any temp files and clean the registry, and resetting internet settings in the command box, but still I get nothing.
View 5 Replies View Relatedhas a netbook which on this one, the network is not working. He connects to the wireless router and gets an ip but he does not have access to the internet.When I tried the netbook at my house with my wireless, it worked perfectly and it stopped working again on my friend's network.
View 7 Replies View RelatedI currently have a sagem router provided by my isp (sky), as the signal does not reach all areas of my premesis and sky refuse to let me use my own router I decided to purchase a wireless extender. I got a Edimax EW-7416APn and configured it using the following settings at the following address:when I connect to the extender i can gain access to the management settings, if i perform a scan using the extender it can see the original router, if I check the security settings they hold the correct ssid, security type (wpa - tisk) and the correct passphrase.
View 1 Replies View RelatedWe have 3 laptops and Verizon high speed wireless internet. I cannot access internet on my Acer it appears that Mozilla Firefox has been "firewalled".
View 3 Replies View RelatedI have a modem/router, planet adw 4401, and i hadn't turned it on for about two months. A couple of days ago, i turned it on. And the Lan connection doesn't work. The lights just turn on at the moment i turn on the router and then they do not turn on. Ok , so i tried connecting through wireless . It did connect but it says no internet access.I'm a bit confuse in what's the problem
View 7 Replies View RelatedI'm trying to connect my portables to a central server that has all my music on it, all located in the same area. I've tried ad-hoc but it limits me to using the preset shared folders only, and its frustrating to use as it breaks once a computer leaves the network.Anyways i just want to create an off-line wireless intranet that will remain persistent even when all computers have left it. This doesnt seem to be possible with built-in windows tools, what program will let me do this?
View 2 Replies View RelatedHave completed a Power Cycle.The affected machine is a HP Elite m9150F desktop. The symptoms include the following:
- neither the LAN connection or the wireless connction will access the internet through Internet Explorer
- microsoft email will not send and recieve
- Steam will not connect
- Norton 360 will connect to live update and download
- taskbar icon shows LAN connection is OK
- When I open Network and Sharing, the network map shows this pc is connected to internet through named network.
- Local Area Connection Status show 197,816 bytes sent and 311,088 recieved.
We have 2 laptops connected to the same wireless network working perfectly. There is also another desktop (Dell 8400) with a LAN connection to the router working perfectly. The affected pc (HP m9150f) is also connected to router with a LAN connection. The D-link Dir-615 wireless router is connected to a Shaw Motorolla modem model SB5102. The HP m9150f stopped connecting a few days ago, other than that, it worked fine.how I managed to get 4 computers running on a network in the first place..
Why I can't acces the internet in public places with my laptop.
View 1 Replies View RelatedIn Windows Vista I am able to connect to wireless router, but can't access internet due to Local message only. Have repaired network adapter , reset cable modemm unchecked version 6 of TCPIP network settings.
View 3 Replies View Related