I'm having sporadic trouble with both Google Chrome and Internet Explorer 8. The first thing I noticed was that the icons on my bookmark bar are wrong. The CNN icon make actually be Amazon and Twitter may be Webster's Dictionary. Sometimes, for example, CNN won't come up at all and then it will display later. Many websites will intermittently come up without graphics and in a plain font.I have done restarts and cleared browser histories and checked extensions. I have performed cleaning with Winferno and McAfee comes up clean
Where I can bookmark a page with information on the Re-call of this router?I am pretty sure that this router is not under a re-call yet but after the endless amounts of discussions and problems folks have had with this thing it has to be recalled soon right?I don't want to loose faith in DLink products because like many I have owned them for years and years. A bad release is going to happen sooner or later but if the company does nothing about the problem it is time to move to a new brand.
At the very least when is the next firmware version going to be released? I have tried them all and none of them seem to work. I am well past the stage of troubleshooting because the problems I have like Way to many other people are not being solved by discussions and firmware changes or altering settings.
I have an ASA 5550 running 8.4(5) and have installed ASDM 7.0(2), but when I try to manage the bookmarks under the Remote Access - Portal when I try to edit an individual item in a bookmark list the screen does not display any information. Is this a know bug, or do I need to have a specific java version for the new ASDM? As a side note, I have not noticed any other issues with the new version of ASDM, only the bookmarks. I initially tried to downgrade the ASDM version that I was using to connect, but it will no longer allow me to connect.
[CODE]My current problem is the internet just isnt working right. It is slow, choppy at times or doesnt load all items on a page. If it doesn load a page sometimes I click on the stop X, followed by refresh and the page pops right upSometimes if I dont get a complete page a refresh will fix it. It is just a pain to work with.There is an Network Connection icon in the right corner of the task bar. It is two small blue screens. It keeps changing from a red x, an exclamation point, and three blue balls or nothing. If I rest on the icon it flashes the status of the network:[CODE]
All network icons missing after running, spybot.In device manager/advanced - wirelss remains off, even after selecting 'wireless on' after selecting wirless on, and closing box, when I open the advance settings, wireless is off again
I want to use clientless webvpn to connect to the inside TSWeb on the win 2000 server.From the inside the TSWeb works normaly, user logs in to the TSWeb site and then click on the application icons that want to use as remote applications (OUTLOOK, EXCEL, etc).From the outside through webvpn the credentials are posted to the TSWeb site, the user logs in correctly, but on the site the applications are not clickable, there is no buttons just the icon and the name of the remote app.What could I change on the TSWeb server?The ASA version is the 8.2.4, and the TSWeb server is IIS win 2000.
I got a strange incident happening to my work computer. Whenever i step away from my desk and come back only to find Icons of files mapped to other network drives other than my local drive have disappeared from desktop. I have to restart my computer to get these back. It only happens when i have walked away from my PC and I have verified that no one has sat at my desk to use my computer while I'm away. The other PC are also networked to the same servers as mine and theirs are not affected at all.
We have 2003 Domain With Active desktop enable for client.Problem Is who ever loging in to my domain they are getting desktop icons in blue color.i have check these but no result
1}My computer properties-advance- performance 2} desktop right click -arrange icons -lock web items on desktop 3} i have checked with display properties.
I have a 2003 server that is doing something wrong. When I show the mac address table I can see that the server is assigning a bad mac address to several IPS. The server assign a non-existent mac address to some IPS for this reason the server stobut I would like to solve the problem
I have a CME on the other end of my MPLS network. When troubleshooting phone issues i setup a phone on the CME system in question and point its TFTP server to the address of the CME router. Now, i need to point this phone to another CME but it keeps registering with the previous one no matter what i do (the TFTP server is pointed to the new CME). I have tried turning off the auto register, and i have deleted the ephone and its mac address all together but it always registers with the wrong CME.
I am having trouble with getting a copier that I have networked to stay registered in the system. When connecting all the equipment back for the new year I was having trouble getting this one specific copier back online properly. I used to have it assigned with a static IP because the person that was here before me had all the computers map the printer using the IP instead of Hostname but that was causing IP conflicts so I removed it and mapped the printer through Hostname which is made "MPF-TOSHRM328"So now for the actual problem, after the copier got the new dynamic IP of 10.8.214.151 i thought it would be fine and everything would click in because it was mapped to the host name and not the IP. But when I do a tracert on the hostname it still shows up with the old IP. and now that the old ip has been reassigned it actually points to a physical machine now. Weird. All attempts to flush the DNS have not resolved the issue. I even tried going in and deleting the entries in manually. No luck. As a point of reference here is the result from the tracert.Tracing route to MFP-TOSHRM328.78B450.nycboe.org [10.8.214.126] over a maximum of 30 hops: 1 <1 ms <1 ms <1 ms SLS330W09 [10.8.214.126]Trace complete. I should also mention that this server is only here in the sense that it is the DC for the computers on this floor. There is a whole other system that assigns the IP's and handles the DNS. I do not have access to it, it is run by the main network people at the central offices.
My folks have Time Warner (Roadrunner) Internet service. They power-down their Dell every night. When they shut down last night they had no problems and were running Time Warner (Roadrunner). When they booted the computer this morning the computer is trying to connect to Adelphia.
They changed nothing. The wiring to the computer was not compromised in any way.
Time Warner tried to "ping" their modem and could not "see" the modem. They think it is a line problem - but the fact that the computer is looking to connect to an alternate service provider makes me think that it is possibly a problem with a setting in the computer.
I have more than 10 PC om my Workgroup, using DHCP on network, but I have one PC alwaws got wrong IP (auto from dhcp), and can't connect even using static IP (status connect, but can't ping to gateway and other IP)Here "ipconfig /all" on one of PC that work. [code]
I flashed my WRT54GL with firmware for a WRT54G and now when I go to the configuration page all I see is this: url...I have tried doing a hard reset by doing the 30/30/30 and by using tftp to try and send the correct firmware. The hard reset does not work and the tftp keeps timing out and not sending anything.
I am trying to allow clients coming in from my "DMZ6" interface with source IPs from the subnet 192.168.2.0 /24 to ping and access hosts on my "DMZ1" interface with destination IPs in the subnet 10.5.11.0 /24. I think I have the associated static NATs and the ACLs set up to allow this to happen. What I have noticed from syslog messages is that the PIX is trying to build the TCP connection to the "Inside" interface, rather than to DMZ1. Even though the destination host (10.5.11.12) is directly connected on DMZ1, the PIX is still trying to send the traffic to the "Inside" instead. I tried adding a host route to force 10.5.11.12 /32 pointing to DMZ1 and the PIX still tries to send the packets Inside. This only seems to happen when I try to go from DMZ6 to DMZ1. If I try to access hosts located in DMZ3 for example, which is also a directly connected interface on the PIX, it appropriately builds the connection to DMZ3. Here are the pertinent rules. Why would the PIX want to build the connection to the Inside, even though it knows that the destination host IP is directly connected to DMZ1?
ip address DMZ1 10.5.11.1 255.255.255.0 ip address DMZ6 10.5.16.1 255.255.255.0 ip address inside 10.5.18.17 255.255.255.240
I am having issues (nothing new there) I have a bad IOS on a switch module, and the config is set to boot to that IOS, and as such I get a nasty boot loop, I am trying to figure out how to get into rommon but all the documentation I can find for this just says go into rommon and never tells me how to get there on a switch module that thinks it has a good IOS. (The IOS is for our normal service module but this one is an odd-ball switch)
I'm in university halls, using the university wireless network. The network seems to be a large number of routers all with the same SSID on the same network.Usually my connection is great; but sometimes my computer decides to switch to the router from another flat. A few minutes ago my wireless config utility told me I was connected to the flat 24 router. I am now connection to the flat 26 router. It wouldn't be much of a problem, only it's give or take, around 140 times slower because of how far away it is. Heres a quick comparison of the speeds:ad Connection: (The ping here is very mis-leading, it took several minutes to calculate the ping and several more minutes simply to start the download whereas on the previous test it was instant)Here is one I took in December which shows how bad the ping can get:How do I tell my computer to ignore those other routers with the same SSID? They have different MAC addresses, is there something I can do with that? Windows can't tell the difference, I have to do it through the driver software that came with my Edimax wireless card, it recognises each router seperately but ultimately it always recognises it primarily by it's SSID. Sometimes it sticks to the good one, sometimes it changes every few minutes and I have to manually change it back and it is very frustrating, can't it just ignore the bad connection completely?
I can't login to change any of the router settings and the router doesn't have any ethernet ports for students to use, so I need a solution from the PC end (If I could i'd simply change the SSID to something slightly different so it didn't clash, then there would be no problem). The router is literally right outside my door, but my computer insists on switching to the one 50 metres away instead
i have a cisco router that has dhcp configured, the router ip address is 10.10.10.***. all computer that attached to the router are using static ip and works fine but when i am connecting my laptop using wireless in gets an 192.168.1.*** address.
I tried to find a suitable firmware for it & found this, Wireless Router, but when I upgrade the device with this firmware , every thing go wrong .. no english language cant upgrade anymore I tried to reset the device to its factory defaults by pressing the reset botumn but the nothing changes
I run a windows 7 x64 and I am currently running a Intel (r) 82579V gigabit network adapter. The thing is, the driver was made for 82579LM and V versions. Most of the time, my computer reads the adapter as the LM version, in which the ethernet just won't work. Once in a while it gets the V version and everything is alright, but i can't live with such uncertainty. Mostly people suggest i should just buy a new motherboard (?) or a new network adapter, but i'm sure it's a software problem. Shouldn't there be other solutions? The card itself is integrated.
Do not have internet connectivity, despite all the lights lit on calbe modem and the ASUS WL520GU router and only the internet and ethernet lights are lit on the Linksys 2102.Despite numerous reboots, no change and even bypassing the router and connecting directly to ATA still no conectivity.When I open a browser, it reverts to the Asus error page, "reason for failed connection: You have set the wrong dynamic or static IP address, though nothing was changed.Funny thing again, a direct internet connection to the ATA did nothing.A google search only just shows lots of unasnered posts on this issue, or only the usual 'please reboot'.
I have an application for work that I need to access true vpn connection :I have Sbs server 2008 with vpn support , I can access my folders and exchange and ... , this works fine.Now I have an application that search to connect to the server via local ip at work but when I use vpn to access it then the application goes searching on my local ip adress and not on the vpn ip adress.vpn has same ip as local ip at work).Now my question is: Can I set the application to search on the range of my vpn connection instead of searching on my local ip when i am not at work but on a different site ?I tryed almost anything but the application still looks directly on my local ip instead of the ip of my vpn
I'm using a DSL line that changes IP's. I have the E3200 set to auto, but everytime the IP changes, my internet goes down, and I get an ip of 127.0.0.1 on the status page. I then have to renew the ip and reboot. This happens once a day, usually.
I have run into a major issue with an autonomous Cisco 1142AP. We were in the midst of a firmware upgrade when something went wrong and caused the AP to reboot in an error mode. Basically the unit was flashing Blue, amber, red. We unmounted the unit from the wall, connected to the console, and it would now only flash red over and over. We pulled out the cisco guides and performed a factory reset on the unit. This still does not work. and the contents of our flash directory is empty. All we get is a ROMMON AP prompt on the unit. If I issue a set command, I can see the default settings for IP, netmask, etc.
I cannot access the unit via the network, even after setting IP info and matching it up to my laptop. Since I have no network connectivity, I can't TFTP a new IOS file to the unit. I am stumped. How to get the config as if it was out of the box, or an alternate way to TFTP to the unit? [code]Notice the lines in red, I must have typed someting incorrectly.Now once the unit boots after being reset, I cannot even type in the CLI. Someting majorly screwed up here. Can the bootstrap be reinitialized?
WLC-4402-25-K S/W - Primary and Secondary Controllers were running 4.2.130 to begin with. Customer upgraded remotely using NCS - Primary to 4.2.209 and then to 7.0.230 and all that went fine and is in Production.
Then customer upgraded Secondary also using NCS also from 4.2.130 to 4.2.209 in preparation to upgrade to 7.0.230 and he lost contact with the controller. Sent a technician to site to troubleshoot by connecting to Serial Port. Technician #ESCAPED out of the boot sequence and from the BOOT MENU tried to boot the Primary Image and it failed with CRC error on Flash. He then tried to boot the Backup image and had the same problem. He then tried to manually load 7.0.230 - ER (Boot Software) using TFTPD32.EXE and that went fine. He then tried to load 7.0.230 "aes" S/W - The big over 70 MB file and went through most of the file transfer but failed saying:
ERROR: Transfer Failed.
TFTPD32.EXE said something like "Data Packet too Short or some such thing". Sorry did not write down what TFTPD32.EXE said.
Then we thought "may be" a power cycle of the unit is required after the ER Boot Loader Image was loaded. When we did that the unit died. That is - no communication with the Serial Port. We don't think we have any choice other than RMA - Do we?
Customer says he did read and follow this link - especially Table 10-1. {URL}. He said he used NCS to do the Upgrade. I a not familiar with NCS.
I have many 1262N and 1031AG APs. when the client is connected to the AP 1262N the performance is slower than it is connected to AP 1031AG (with more clients) in 2.4GHz.
