Router Ip Address Is Not Accessible?
Jan 31, 2013
I have a linksys router and i'm having quite a big issue. it's been since 2010 that I bought it and have no problems up until recently. I was playing/ going through all the security settings just to what all there was to secure my router. I noticed an ip setting and I 95% sure I did something which changed it; and now i am unable to access my router settings. Whenever I type the old ip address (192.168.1.1 or any of the few other ip addresses) it gives error page and says this page is non existent or it gives me a link to click on with the failed ip address to do a google search. My question is, is there any way that I can reset the router (like a system restore on a computer),
View 2 Replies
ADVERTISEMENT
Mar 18, 2012
I manually set an IP address in my new SG200-26, and turned off the dhcp client. I cannot access the webpage or ping the switch at the statically set IP. I have also run a network scan and tried accessing the switch at all of the IP addresses in my DHCP Pool that were being used, it is not available there either.
View 1 Replies
View Related
May 10, 2012
Here's what I have WAN->SonicWall->E1200 Basically the E1200 is given a static IP for it's WAN that is in the range of the Sonic Wall's DMZ interface, and the DMZ interface is the default gateway of the E1200. When wireless clients connect to the E1200 they get internet access with no issues and they are on a separate network (which is intended). The issue I have is if I get on a computer that is on the Sonic Wall's LAN network, which is able to route to the DMZ network, I am unable to ping the E1200 or perform remote management (turned on in the E1200). There are phone devices that are on the DMZ network that I can ping from the LAN network. I need to be able to remotely manage the E1200?
View 1 Replies
View Related
Feb 2, 2012
2 linksys routers a E1000 (fw v2.1.02) and a E4200 (fw v1.0.03) aren't accessable via HTTPS. Both via LAN https://router-ip and via wan https://isp-router-ip:8080 . Both routers are configured correctly (allready did a rerstore to fact. defaults. while having a chat with linksys live chat support). Everything without a result.
Ie9 doesn't accept the linksys/cisco certificate. after the first warning ie9 just sais that it's unable to show the page .
I did some testing and found that it doesn't work with a win7 +IE9 (up to date updates) and also not on a win XP +IE8 (up to date updates), win XP +chrome (up to date updates).
And it works on a old image (virtual Pc) of WIN XP- IE6 (no up to date updates) and win XP(up to date updates) +firefox (older version) .
i tried to export the certificate using the xp-ie6 virtual pc. and import it else where, but that works within the lan. Over the WAN it's a " NO GO" . Is this a " Microsoft" or a " linksys/cisco" issue?
View 9 Replies
View Related
Jan 22, 2012
I am no longer able to access the "EBay" website while working on my wireless router. I have 3 personal computers, a laptop, 3 android smartphones & 2 ipod touch's. They all work fine, from my wireless router.I have the WRT54GS ver. 6.
The problem started with not being able to access EBay. I called the EBay people. Then, I called my local Internet Service Provider. There were at least 10 phone calls, to each. Then, I called the Linksys people. The lady told me that I had an outdated router and that I needed to get a new one. Well, I had previously bought the most expensive one I could get, said it was for "optimum" movie & gaming from Cisco.
View 9 Replies
View Related
Jan 25, 2012
I have IIS running in a machine inside my network and I would like to make is visible to the world wide web.To do that, I created a website in the port 8787, which is accessible when the user types 192.168.0.126:8787 in the browser. Of course it works only when the user is inside my network.(IIS running over windows server 2008 OS)Now I want to make it visible to the WWW, so I created a rule to make a port forwarding to it:I went to: Advanced > Virtual Servers and created a rule with the given information:
enabled
Name: website
private ip: 192.168.0.126
protocol: both
private port: 8787
public port: 8787
Schedule: always
This rule created automatically a firewall rule
Enabled
Alow
Source: WAN *
Destination: LAN 192.168.0.126 Protocol: * Port range:8787
always
Unfortunately it isn't enough, if I type myPublicIp:8787 I can't access the website because I either get "connection reset" error or a timeout.I pluged my computer directly in my modem and it worked perfectly.To make a test, I tried to enable the router remote administration on the port 10001. It didn't work.ps: my wireless router is a dlink di-524, I am writing this in this forum because I couldn't find the one related to my router...
View 1 Replies
View Related
Jul 19, 2011
I have connected a Seagate Free Agent 500GB to the USB port of my E4200 and while it does work fine, When the drive has been idle for a while, it goes into power saving mode, turning the spindle motor off. This means it takes a few seconds to access the disk. Not a problem, but apparently, those few seconds are enough for either Windows or the E4200 to decide that the disk is no longer accessible. The share is still available, but I get missing folders and files, files won't open or are not found, and backups job with Acronis True Image will fail because it thinks the share is unavailable.Sometimes, constantly refreshing the view and opening files at random will revive the share, but often, the only way to get it back is to restart the computer.
The problem is definitely related to the power saving. If I leave a video clip playing or similar, so there's always some disk access preventing the drive from entering power save mode, it works fine. But 15-20 minutes of no disk activity immediately causes problems.
View 3 Replies
View Related
Feb 1, 2013
I am experiencing one, possibly two problems with the X3000, firmware release v1.0.03:
1. When enabling guest mode, the internal network is not accessible via WLAN even for clients NOT connected via guest mode but regularly: Even non-guests but regularly connected clients can't access any internal IP but the router itself. netscan shows only the very client's IP and the router's. Only after switching guest mode entirely off, regularly connected clients can access interal IP again. netscan correctly shows the whole network. Obviously a firmware bug. BTW: Clients connected via cable do not experience this problems.
2. I am not sure about this, but after using the firmware built in "Reboot" button, the router reboots correctly. But for some reason, it is instable afterwards. It is operational for a few seconds but then reboots again. It keeps cycling. I could stop it by switching the router off and on again.
View 6 Replies
View Related
Feb 2, 2007
We have a RV042. remote management is set to DISABLE - but even after restarting the router i can access the interface remotely over the internet.even when i enable it and change the port to say 5555 i can connect to the web interface using either port 5555 but ALSO on port 80.what's wrong here?the only way to stop that was to create a rule that blocks port 80 on the WAN interface. (btw. could this rule affect LAN users when browsing the web?)
View 7 Replies
View Related
Mar 9, 2012
Ok so one site i used to use regularly has for the last few month been either incredibly slow or totally inaccessible. Its a perfectly sedate site just a social forum, its this one. www.pandemoniumcarnival.com/ which is accessible to all my friends but seemingly not to me...So far i have changed DNS (to open DNS and Google, thinking my isp had blocked it for some reason)Tried Firefox (my usual browser) chrome, IE ...flushed all the settings etc in each no cookies etc. Tried "In Private Browsing" etcOddly i can get to the site if i use a site called "Hide my ***" a proxy server thing. But even then its not fully functioning due i think to the proxy setting (?)
View 8 Replies
View Related
Jul 16, 2011
I switched from Time Capsule with AirPort to E2000 and have a problem with configuration.I use the same IPs as in AirPort and E2000 gives me an error:"The WAN IP address cannot be the same subnet as the Guest Network IP address" and I can't save configuration.But in my opinion they are different.I use "Static IP" option and I have IPs from my ISP: [code] So WAN IP is different subnet as LAN and I don't know what to do now. It worked with these settings in AirPort and here I can't proceed.
View 2 Replies
View Related
Feb 28, 2011
Is it possible to assign public IP address as Router's local IP address (RVL200, RVS4000)?
View 1 Replies
View Related
Jul 3, 2011
I have a Linksys WRT54GS v5.1 router running firmware 1.52.5.I am trying to use Linksys IP Phones SPA942, but these do not seem to be able to log on and just show "Initializing network" even though the MAC address appears in the router with an IP address.The strange thing is that I already have 4 SPA941 phones that work with no problem and just log on to the network.Is there something about the SPA942 that I need to configure differently, I have factory reset it with sucess, but still unable to log on to the network.
View 1 Replies
View Related
Feb 22, 2011
i found WAN Miniport (IP) - in my windows xp and at the same time my Lan systems are not accessible.
View 1 Replies
View Related
Mar 19, 2011
I'm working on a small network (1 server, 6 workstations, stand-alone, not connected to the main Company Network) "reinstalling" a Workstation. Re-imaging from semi-generic Norton Ghost image (4 of the 6 Workstations run the same programs with different addresses). I then had to reset the IP, the Computer Name, and then the Domain (I did it in that order).
I'm using Windows Server 2003 as the domain controller, and the Workstation is Xp Pro Sp 2.
The Workstation is using the same IP, Name, User as before, and they were working with the server previously (a program had corrupted prompting the reinstall).
The problem is that if I open windows explorer and type in the Workstations IP (\000.00.0.1) I get access to the computer. But if I go there and type in the Workstations Name (\Computer01) I get a "you may not have permission to use this network resource" error.
If I go to the work station, and try the same thing except with the Server's IP (\000.00.0.100) and Name (\Server01) I get access.
This Workstation controls an I/O device that is used by a program running on the server (most of the time, not while I'm doing the install of course) and the program uses the Workstation's Computer Name to access it.
As far as I can tell all the settings on this Workstation match the 3 that are running the same programs, but I could have missed something.
I'm a bit stumped by this, I don't normally deal with the Server side of the computers. I usually just set up the workstations to whatever Name/IP the Net-admins give me. But my bosses put me in charge of this little network, mainly because the Net-admins din't want to deal with it.
View 2 Replies
View Related
Jul 8, 2012
I was trying to connect my computers on a home network so that I can access either one via the other.When I try however I get the message:
"***-PC is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions.
long failure: user account restriction. Possible reasons are blank passwords not allowed, logon hour restrictions, or a police restriction has been enforced.
That is the message from computer 1 to computer 2.
Computer 2 gives me the message:
Windows cannot access \***-PC
Check the spelling of the name. Otherwise, there might be a problem with your network. To try to identify and resolve network problems, click Diagnose.
View 2 Replies
View Related
Aug 31, 2012
I can not access shared windows 7 c drive in windows xp. how can i view these system
View 3 Replies
View Related
Jun 1, 2012
We have an ADSL connection and use a D-Link DSL-320B modem. We have a D-Link DIR-120 router connected to this modem. This has worked perfectly fine up until today when we disconnected the router and connected a computer (call it A) directly to the modem because it was getting an unusable connection through the router for some reason. We later also performed a factory reset on the DIR-120 router.
Unfortunately, after the above steps the router did not receive any IP address (through DHCP) from the ADSL connection anymore. During my attempts to debug this I noticed that my laptop (call it B) didn't get any IP address either (when connected directly to the modem). I noticed the following syslog entries repeating over and over while trying to connect: [code]
At this point computer A could still get a connection just fine tho (when connected directly to the modem).
I then tried to change the MAC address of the router to an arbitrary one (a copy of computer B's MAC address but with the last digit increased by one). The router still did not get assigned any IP address. Finally I tried making the router clone the MAC address of a third computer (call it C). C has never been connected directly to the modem. Doing this worked. After cloning the MAC address of computer C the router is immediately assigned an IP address and the internet connection works as it did prior to all this.
Now, my question is, why would computer B and the original MAC address of the router not be able to get an IP address while two other computers worked just fine? Why would changing to an arbitrary MAC address not work while cloning the MAC address of another computer did? Could the router's MAC address have been blocked by the ISP for some reason (and what could cause this)?
but my situation seems more like a blacklisting of some MAC addresses rather then allowing just a single MAC address.
View 1 Replies
View Related
Mar 26, 2011
I have a fairly simple wireless home network. My main desktop machine is running XP Pro, and our family laptop is running XP Home. The laptop shares the My Documents folder for 2 of the 3 profiles. One of them works as it should. It is visible and accessible on the main desktop machine, but the other share is visible but NOT accessible. I get the following error message when I try to explore it from the main desktop machine:
<the share name> is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions.
Access is denied.
I'm not sure when this started, but remember that the other folder being shared is working just fine. I've double and triple checked the settings, share names, and basically anything I could possibly mistype. I've restarted both PCs, and refreshed the network explorer via both the file explorer and My Computer dialog. The My Computer dialog refresh the shares for some reason that the explorer wouldn't, but I'm still denied access to that one share on the laptop.
View 2 Replies
View Related
Aug 15, 2012
I have a Windows 7 machine that is wired to the router. I have Windows XP computer that is wireless in another room. Signal is showing 80% and internet is accessible and fast from both systems; but, I cannot access either computer from the other computer. I got the IP addresses of each machine and I cannot ping from either direction. Firewalls are turned off on both systems.When I type in \server, I get an error that say I should check my spelling or use the windows Search; but, that doesn't work.
View 5 Replies
View Related
Jun 28, 2011
I have a Motorola Affix and am using the app printershare to print from my phone to a network printer at home.. it works great.. but I want to know if there is a way to make the printer accesable from the internet so I can print from pt phone when im not home and connected to the network...accessible
View 2 Replies
View Related
Jun 29, 2012
Cannot Ping System but system can ping everyone on the network accessible
View 2 Replies
View Related
Apr 19, 2012
My pc (windows7) will say its connected.. It even says internet access.. But when I click in the Internet?THE WEB PAGE IS NOT AVAILABLE. It says the DNS lookup failed. But the thing is... all my friends bring their laptops over (Mac & Pc) and try work fine. Even my phone catches the wifi perfectly in my house. I started to think maybe it was the laptop but the laptop word great on wifi at my job, my friends house, and pretty much anywhere with wifi but my house. I have wifi through bright house and they came to my house one day but they ended up not doing anything because they can only make sure there device (router) works perfectly. Ok.. So I took the laptop to best buy's geek squad and the guy "reseted my network card" & told me it should e fine when I got home.. Nope. Didn't work. I have spent hours looking trough the Internet trying things that people recommended I do. (start, run, cmd) I've tried it all. It just won't work. I really need this laptop to work at home because I do a lot of work from the pc. I hope somebody on here could point me into the right direction before I give up & toss this laptop in the shed and be forced to purchase a new one.
View 8 Replies
View Related
Jan 19, 2011
I have a router-based home network in which the desktop running XP media center is connected by cable to the router. There are 2 wireless laptops, one running XP home and the other Windows 7.The laptops can talk to each other, and the desktop can talk to the laptops.But I cannot access the desktop from the laptops. I can see the (shared) folders, but when I click on one I get the message: "You might not have permission to use this network resource..Not enough server storage is available to process this command." One solution suggested in several places is to change the IRPStackSize to 15. However, if I start the desktop in safe mode with networking, I can access the files.I can also access the machine using remote desktop.One extra frustration is that this is a problem that has happened relatively recently. It used to work OK.
View 8 Replies
View Related
May 21, 2011
I have a question that�s been bugging me and that internet searches didn�t quite explain and that is how do I make a resource available publicly e.g. web serverAll I hear so far is register a domain name but that doesn�t quite answer the full question. Id like to know exactly what happens when a user types in the url of my web site and how their traffic gets to me. Is it.. get a static ip from my isp then provide this to the domain name registrar and that it now every one can access my site?? Seems to simple.
View 1 Replies
View Related
Jan 20, 2012
I created a share on our server for a few AD users and set those users up in a group I set that group to have the permissions to read/write this share. When one of those users tries to connect to the share from a PC, he is denied permissions, but when the same user connects to the share from a Mac, the file permissions work as they are set.I checked effective permissions for each user in the group, and they have the access they are supposed to. I've tried re-creating the share, recreating the group, and comparing the permissions to another share that is set up the same way (but working properly).
View 2 Replies
View Related
Dec 5, 2012
i have shared 4 network drive in my client computer but sometime when we leave computer on for a couple of hours and then try to access the drives then it shows the message "network drive is not available" the only way to access the drive is to restart computer.
View 1 Replies
View Related
Jun 8, 2012
Would it be possible to make a printer accessible from internet? Need to print a lot of batch printing from my cloud application , in that case can we direct this print job to a specific printer over internet ?
View 1 Replies
View Related
Mar 18, 2012
I setup a site to site vpn between location A and location B.The setup is working and both location can see each other. Now the problem is last weekend the vpn is not UP although the Internet is accesibble. The solution is i power off - on the ASA 5510 and the vpn connection is UP again. This already occurs 2 times. The 1st times is 4 month back. The 1st time i thought is nothing, but the 2nd time, I really need to know what wrong?I attach the configuration of the ASA 5510 at location A that i reboot.
View 2 Replies
View Related
Jul 28, 2010
I recently ( three days ago ) purchased a SRP 527w and have been using it in a mixed Mac/Windows network. The setup is currently primarily using defaults apart from enabling logging. While I was still able to access the internet with some applications, accessing web content appears to have blocked after approximately 48 hours uptime.
No web pages using port 80 were available and that included the router web interface. The router would respond to ping only.
On a different note. I have to say that I find it very strange that the supplied documentation doesn't advise setting up the router using the admin login. It was only after reading one of the comments on this site that I was alerted to this security problem. I also find it rather annoying that I appear to have to purchase additional support merely to be able to download firmware updates which are designed to give the device improved functionality.
View 51 Replies
View Related
Apr 7, 2011
Cisco ASA 5510 with static routes. I created a new internal vlan and added the correct route to the ASA. Internally the vlan is fully accessible but when I connect to the VPN I cannot communicate with systems on it.
The dynamic access policy and associated ACL are fine. A system associated with this policy but not on the new vlan is accessible thru this policy.
View 4 Replies
View Related
Mar 23, 2013
I have nated my 172.81.15.0 255.255.255.0 into my internal server 10.1.10.164 , i can ping the out side server but the internal server is not accessible from out side static (Database-Servers,interface-sms) 172.81.15.2 10.1.10.164 netmask 255.255.255.255icmp permit 172.81.15.0 255.255.255.0 interface-smsroute zemen-sms 172.81.15.0 255.255.255.0 10.131.199.201 1access-list Database-Servers-in extended permit tcp host 10.1.10.164 host 10.185.62.144 eq 9090access-list Database-Servers-in extended permit tcp host 10.1.10.164 host 10.185.62.144 eq wwwicmp permit host 10.185.62.144 interface-smsi can ping the out side server 10.185.62.144 with out a problem . from the server 10.185.62.144 i can ping untill 172.81.15.2 and it will not ping the natted server 10.1.10.164. as u seen the accesslist ping is permitted.
View 1 Replies
View Related
Nov 6, 2012
I have a DVR system. Which is configure in DMZ on my firewall. DVR internal IP is 192.168.2.13 and external IP is 27.34.xxx.xx. when I am able to access DVR by using internal IP and it works fine while accessing from the internet it not work proper. Though it prompt for username and password also. After enter the login credential its getting blank. I am able to telnet External IP from internet on port 80.
View 1 Replies
View Related
