Cisco AAA/Identity/Nac :: ISE / Getting ASA5505s For Tunnels To The Main Location?
Jul 29, 2012
i'm working with a client on an ISE deployment and they would like to have the remote locations take advantage of it for dot1X. The potential problem that i see though is this--they have ASA5505s for tunnels back to the main location, which is great, but they also use the built-in switch...i know there are issues with the larger ASAs that require the IPN. I'm wondering if they'll need a different switch for this to work?
View 2 Replies
ADVERTISEMENT
Mar 22, 2012
I am a employed at a credit union with 17 branches. We have a mpls circuit connecting the branches to our main office. I setup DSL as a backup connection. I have 17 RV042 Cisco VPN Routers. I created a secure vpn tunnel for every branch to the main office. I made a delayed route in our main router to fail over to the VPN, in case the mpls failed. Almost everything works great except our ATM's are required to connect to a router at our main office to a different subnet than the tunnel is connecting, therefore not routing through the tunnel. I've tried creating another tunnel but only works with one of the branches, cause I get a conflict at the main office when I try a second tunnel with the same ip network. Also I tried routing all the traffic through the vpn by putting in the address 0.0.0.0 subnet 0.0.0.0, at the branch site. But I can only do that for one branch, The Downtown Cisco won’t let me create another tunnel with that setting.
View 1 Replies
View Related
Jun 13, 2012
I am trying to move a device from the Default location to a sub group and get the following message when I try (either with IE or Firefox)
This System Failure occurred: Index : 0, Size: 0. Your changes have not been saved. Click OK to return to the list page.
it also gives me the same error if I try and change the Device type from default to a sub group. I'm sure I could do this previously. The ACS build is (VMWARE install):
Cisco Application Deployment Engine OS Release: 1.2ADE-OS Build Version: 1.2.0.228ADE-OS System Architecture: i386
Copyright (c) 2005-2009 by Cisco Systems, Inc.All rights reserved.Hostname: ACS1
Version information of installed applications---------------------------------------------
Cisco ACS VERSION INFORMATION-----------------------------Version : 5.3.0.40Internal Build ID : B.839
I'm suspecting it a read/write issue with the database or a database corruption. I have stopped and started the application acs via the console and show application status acs has the following to say about itself.
ACS1/admin# show application status acs
ACS role: PRIMARY
Process 'database' runningProcess 'management' runningProcess 'runtime' runningProcess 'view-database' runningProcess 'view-jobmanager' runningProcess 'view-alertmanager' runningProcess 'view-collector' runningProcess 'view-logprocessor' running
View 3 Replies
View Related
Oct 24, 2011
I have a pair of 5505s with an IPsec VPN between them. On the first 5505, I also have a user connecting to it via client based vpn. The user cannot access systems on the other side of the ipsec tunnel. That 5505 protects subnet a.b.c.d, the user is on subnet a.b.e.d which is not inclusive to a.b.c.d. First, am I correct in the assumption that I need to add the vpn network of a.b.e.d to the list of protected networks, and second if I change the list, does it drop and reset the ipsec vpn?
View 2 Replies
View Related
Aug 28, 2011
I am planning on setting up a site to site VPN with two ASA5505s across a WAN connection. Take a look at my setup and answer this. To get this started, I would need to get my ISP to route any traffic from my external IP address to which address: 192.168.100.220 or 10.255.255.2. I have never done this before. Inside port is 192.168.100.220, Outside port is 10.255.255.2
View 12 Replies
View Related
Mar 2, 2012
would you explain the main differences between lms 3.2 and 4.2 cause my company is about to purchase the new version;
- how does it changed in taking reports ?
- how does it changed and improved in monitoring?
View 1 Replies
View Related
Sep 6, 2012
My computer at work crashed so I had to reinstall windows 7.When it was working properly I was able to connect to our main server computer. After the reinstall I am able to connect to the internet however I am unable to connect main server computer. Usually, before it crashed, the server would automatically show up in the networks folder. Now all I can see it my computer and not the server computer.If someone knows how I can get my computer connecting to the main server I have tried everything and nothing is working.The main server computer it Windows XP and my computer is Windows 7.
View 4 Replies
View Related
Jan 16, 2012
Whenever my main PC is turned on, i get no signal from the wireless, like i cannot use my phone or laptop on the internet i use an Ethernet cable which is directly connected to my main PC my windows is also window XP and my modem model is TG782T only if my PC is turned off the wireless works
View 2 Replies
View Related
Mar 22, 2011
I have four Laptops,and also have SMCWBR14S-N4(SOHO) Wireless Routers. The issue is if i connect to my main Laptop all the other laptops gets disconnected. I have checked the mac filtering, reset the Router & reconfigured with new wireless settings still the issue persist. If i connect the Laptop to the modem main Laptop works fine.
View 4 Replies
View Related
Jan 16, 2012
Whenever my main PC is turned on, i get no [COLOR=blue !important][COLOR=blue !important]signal[/COLOR][/COLOR] from the wireless, like i cannot use my phone or laptop on the internet i use an ethernet cable which is direclty connected to my main PC my windows is also window XP and my modem model is TG782T only if my pc is turned off the wireless works
View 17 Replies
View Related
Jan 16, 2012
Whenever my main PC is turned on, i get no signal from the wireless, like i cannot use my phone or laptop on the interneti use an [COLOR=blue !important][COLOR=blue !important]ethernet[/COLOR][/COLOR] cable which is direclty connected to my main PCmy windows is also window XP and my modem model is TG782T
View 2 Replies
View Related
Feb 9, 2011
A couple days ago my administrator account stopped being able to connect internet via wireless or Ethernet however my other accounts can still access it. I went to find a restore point but they have all been deleted. I'm not sure if it is a virus or something else.
View 5 Replies
View Related
Jun 27, 2012
I have a problem with my SIP trunk config. I can receive calls, but unfortunately I cannot dial. I found out why, and it is because I have one main registered number from TISP, and I am trying to dial with the phone number from the block. That is why I am receiving unauthorized messages when I enable debug ccsip messages. I called TISP and they said that I should always use main number and to send my number via P-Asserted id. or via P-Preferred Id. how to configure this ? I found only this conf.
Commands:
dial-peer voice tag
viace-class sip asserted-id pai or ppi
I tried with this but it didn't work. I don't know where to say what I need to insert , and instead of what .
View 1 Replies
View Related
Oct 8, 2012
After reading a bit about interVLAN routing got a doubt regarding how trunking takes place at router and at switch.In case of switch we configure a port interface as trunk port and say all vlan's are allowed here but in case of router we configure sub interface as trunk saying particular vlan belongs to particular subinterface .Can't we configure only a single port interface on router just like Switch and say all vlan's are allowed here on this interface ,why to go for sub interfaces?
View 2 Replies
View Related
Jan 21, 2013
I just joined this company and they already ad a VPN to one of their partners that provides them access to some resources. We have now added a 2nd location but the partner wouldnt allow a 2nd VPN tunnel so the decision was made to give the new location a ASA5505 to tunnel thru the main office to access the resources at the partners site.Using ASDM i believe i was able to setup the tunnel to the main office but there is no resource there to use. Now i'm stuck and i do not know what to do to get to the partner site
View 4 Replies
View Related
Jun 6, 2011
i replaced a lightning damaged Linksys router in my home network with the RT-N56U. My main computer is Win7 64, (Phenom II quad, asus M490GTD) , my wife's computer(wired connection, Dell P5Duo) and my work laptop (wireless connection HP core I5) are XP. I have a USB printer attached to the wife's computer and two wireless Squeezebox receivers. This network worked with the old router. With the new router i can access internet from all computers, and connect to the new network with the Squeezeboxes. I cannot print from the main computer, even though the printer shows up in the devices window and the test page spools.
View 4 Replies
View Related
Aug 1, 2011
tell me the reasons that could cause the decreasing of the bandwidth in the TP cables? just 3 or 4 (main) reasons.
View 4 Replies
View Related
Jun 13, 2011
I have at last got the wireless router today and set it up. A few teething problems but I have the internet and so does my wife now. And, I have my computer back! The new wireless router is a D-Link DSL-2740R. There are two things I can't get sorted out, I put admin into the user name and I can't seem to find a way to change the user name
I managed to get the laptop (WinVista 32bit my comp is Win764bit) seeing the media from my computer but not other files and printer. I had previously set up a user under 'share' to enable the link between the computers and using the old Belkin it worked fine. Alas that is not the case and want it to get the sharing going. The 'Share' user is still setup and I could not see it, or I have forgotten how to access it?
View 2 Replies
View Related
Mar 9, 2013
We have wireless in the house, the router, etc is down in the basement where my office is. Is there any way to increase the strength to the main level of the house? Our house is standard size, but it seems to weaken upstairs.
View 4 Replies
View Related
Aug 15, 2012
I currently have a BT Home Hub 3 router and an Ubiquiti Power AP N. What I am trying to do is use the Ubiquiti access point as the main device for all connections in my house (ethernet and wireless) so that I can use the QoS settings etc. I basically want the Home Hub router to play as little role as possible in the network except for providing the ADSL internet connection. How would I be able to do this?I know I need to enable DHCP on the access point but everytime I do so the devices connected to the access point lose internet connection.(BTW I have an ethernet cable connected from one of the routers LAN ports into the access point's WAN port)
View 3 Replies
View Related
Jan 20, 2013
I just recently got back from a 2 day vacation to find that my internet on my desktop is almost unusable. I can get onto some websites and load videos, but it takes hours. I use Skype quite a bit, and I play online games. It is literally impossible to do either without my internet disconnecting.I use a 2wire Router i3812V with AT&T U-Verse. Here are my specs:[CODE]
View 1 Replies
View Related
Jun 27, 2012
Iv got an "old" dir 655 laying around as my secondary router and found out it had an USB slot for share port.In another room of the house Iv got a media center and an Usb printer. Can I use this dir 655 as a wireless bridge from my main router, so the media center and the printer can be connected? So both low level streaming and shared printer with share port.Or do you need to be connected directly to the dir 655 to use the usb and share port?
View 11 Replies
View Related
Sep 30, 2011
I have extension mobility configured and working fine. Except that when you log into the phone, the phone does not exit back to the main display. To get back you either need to exit out of the menus by pressing exit a few times or press the globe / web button on the phone.
View 6 Replies
View Related
Jun 10, 2012
We have a main office and 4 remote offices (only showing 1 remote office in the diagram). We are using GRE over IPSec VPNs to the remote offices which terminate on the 2811 router in the main office. We are using the 2811 as it is the only device that we have that can terminate GRE. The 2811 router is connected to the outside switch and is configured with a public IP address. We also have a ASA5510 in the main office which is connected in the same manner and is used for Web, e-mail traffic etc.Both the main office and remote offices have a 10Mbps Internet connection.
We have an issue with voice quality between sites as we are finding it difficult to control bandwidth utilization in the main office. When users in the main office download web content it can saturate the 10Mbps Internet connection causing voice quality issues. We have configured outbound shaping on the branch routers to make sure that aggregate inbound traffic from all branches to the main office does not saturate the link but we cannot control traffic from the Internet.I understand that controlling inbound traffic from the Internet is difficult without controlling QoS on the ISPs side. Is there any way that can reserve inbound bandwidth to ensure that web traffic does not impact voice? Also in this design, which is the best place to configure outbound QoS from the main office?
View 4 Replies
View Related
Jan 24, 2011
I have a Cisco router 877. I am trying to configure a backup with ISDN.The primary line is an ADSL over pppoe. The problem is that despite the primary line fails, doesn't change the path and continue going by the main route.I have a very similar setup, also with a cisco 877, but with a normal DSL and it works perfectly.I solved the problem by activating a tracking but is slower than the other method.
View 2 Replies
View Related
Dec 6, 2011
Trying to implement HREAP over WAN between main and remote site. The WLC4402 is on main site. There will be a secondary DHCP at the remote site. Does the switch at the remote site any preparation?
View 4 Replies
View Related
Mar 1, 2013
my RV042. The main login password has expired but it will not let me change it at all. Basically I try to login but get the error 'The old password has expired. Please change the password'. But with no prompt at all for a new password and just a return to the login page. Tried various different browsers, tried the old default password but nothing will work. There seems to be no way of changing it and I cannot login.
I really don't want to reset it to default as I have numerous VPN tunnels configured and various other settings.
View 5 Replies
View Related
Aug 16, 2012
My ASA's have the follwing Versions: ASA Version 8.4(3) ASDM Version 6.4(7)Have I a chance to configure a site-to-site tunnel with a hostname as peer address when I will use Identity and CA Certificates?
View 2 Replies
View Related
Aug 1, 2012
main computer will not connect to internet but laptop does
View 1 Replies
View Related
Jun 27, 2011
I have a desktop computer which is connected to the router by cable, but when this computer is on I can't connect to the wireless network with any other devices.When I turn the main computer off though I can connect fine with any wireless device.
View 3 Replies
View Related
Apr 28, 2011
I have 2 computers (one is using windows 7, other is using windows xp), one switch and router. I don't have physical access to router. I have plugged the cable from router to switch, and connected both PC's to switch and now I have internet on both PC's.My question is, can I "control" or share files on windows xp with Windows 7 (main computer) and in same time have access to internet? Or to use windows 7 to connect to internet?
View 5 Replies
View Related
Apr 12, 2011
I have a network where I have two wireless routers wired to a third (main) router. I want to connect a third wireless (Linksys WRT 54GL) to the main router,but I want to connect wirelessly (without any cables). I have tried to bridge it,ie disabling DHCP and assigning a static IP address which is in the same range as the main router but still if i connect my laptop using the third router I cant log onto the internet and worst still I cant ping the main router. The main router is the one that is connected to the proxy server. My connections are as follows,from the wireless antenna the cable goes to the proxy server's wan port,the main wireless router is linked to the server's lan port.My server's LAN ip is 192.168.0.1 and the main wireless router is 192.168.0.2 I have two other routers which are wired to this main wireless router and their local IP addresses are 192.168.0.4 and 192.168.0.5 respectively. I want to connect a third wireless router to the main router but this time without using a cable. What i have done so far is I have assigned it the IP address 192.168.0.6 and I have disabled DHCP,all the other settings I have put the same as the main wireless router.
View 2 Replies
View Related
Aug 29, 2011
1.I want to have a seperate Broadband line for a Server running TS for certain users to log into to.
2. I want another broadband line that is split via switch for other users and servers.
Reason: Speed up connection for TS users so that are on a dedicated line.
How will I get TS Server to speak with my Main File server to access the files they need and there is 1 folder both networks should have access to?
TS server and Main server in Same building. Don't want to use a WAN routers to connect the 2 routers together. My Broadband (According to speedtest.net = 12Mbps DL/ 0.80Mbps UL)
View 2 Replies
View Related
