[OK] webvpn
webvpn
[ERROR] anyconnect image disk0:/anyconnect-win-3.0.08057-k9.pkg 2
copying 'disk0:/anyconnect-win-3.0.08057-k9.pkg' to a temporary ramfs file failed
Trying to add the windows anyconnect to the list of usable software for clients and that error happened. What is going wrong? I assume I dont have enough RAM...
I have a 3560x switch with the flash formatted . I have tried to solve the problem by copying the IOS file to the flash. But the boot failed either .I have tried to copy the same IOS by the Xmodem, The boot failed again.My question is how to fixed the boot issues after the flash was formatted?
View 4 Replies View RelatedI recently had some trouble with my ASA 5505 in that the running config would not be saved after a reboot. Definitely looked like a hardware problem with the flash memory. I have since bought a new flash memory card and copied the contents of the old card to the new card. 1st problem I have is that I can see the image on the new card, but for some reason it wont boot into that image. I get /file not found
I then successfully load a new image to the device and it boots successfully. I then follow it with a
Cisco asa# config t
Cisco(config)# boot system disk0:/asa831-k8.bin
(to ensure it boots from the flash in the future) and I get
WARNING: BOOT variable added, but unable to find disk0:/asa831-k8.bin
I have since tried
ciscoasa# fsck disk0:
Unsupported file system type!
%Error checking disk0: (No such file or directory)
When ever I try to do anything with Disk0: i get the same error. (No such file or directory). I have also tried putting the old flash card in the ASA and I now get the same response.
How do i copy the configuration file from a switch to a storage device (USB)
View 1 Replies View RelatedI have a Cisco ASA 5510. I am trying to copy large files between DMZ and INSIDE network and it is copying at awfully a slow speed. I thought it might have been related to duplex mismatch but it doesn't seem to be. DMZ interface is set at 100 full duplex. I programmed the port on the managed switch where the DMZ uplink is connected to be 100 full duplex. I even hard set the NIC on server to be 100 full. Nothing worked. So, I come to a conclusion it isn't the duplex mismatch but there gotta be something else on Cisco ASA. I was googling for this issue and came across it could be a QoS policy. Now, checking my ASA I see a any to any global service_policy where it is defined to inspect certain protocols where 'netbios' is one of them (among others such as 'ftp', 'tftp', etc. Could the slow copying be related to the above policy? Could there be a bandwidth limitation between DMZ and INSIDE interface? How do I check?
View 5 Replies View RelatedOur office lan network is in 192.168.0.0/16 with 300 nodes and 30 server .Since its a large broadcast domain some times it takes large time for copying files.How can we avoid this problem with out changing the subnet.Also how to avoid broadcast storm.we are using cisco 2950 series switch.
View 10 Replies View RelatedI have wrt610n that i have wd 1 tb drive hooked to usb port and when i try to copy large folder/files to it, i get the dreaded- cancel, try again skip and it locks up solid. i have treied all settings in these and other forums. i have tried two different brand size hard drives, i have tried wireless and wired and nothing. is there a fix for this. i have latest firmware on everything, i have everything set tweaked best as they can and not one things makes a differance. all i get from linksys is try this try that. is there a way to copy large files to hd first via the pc then hook back to the router to see the files?
View 1 Replies View RelatedI am having Cisco 3845 series router with c3900-universalk9-mz.SPA.151-4.M2.bin IOS . I want to install new Licence on it for DATA. When i am trying to install licence on it i am facing the error "% Error: License installation failed with error: XML parsing failed".
View 4 Replies View Relatedhave a ACS 5.2 version installed on Vmware . I purchased below liscense
Product Name : L-CSACS-5-LRG-LIC=
Product Description : L-CSACS-5-LRG-LIC= : ACS 5 Large Deployment License (Electronic Delivery)
When i am trying to upgrade the liscense i am getting an Error " Liscense file installation failed : The liscense file must contain single base liscense "
After unable to connect to my wireless network, I did a restore - but got a message: System restore failed to replace the file (C:WindowsServiceProfilesLocalServiceAppDataRoamingPeerNetworking98c An unspecified error occurred during System Restore (0x80070002)I've tried 3 restores to get the same message.Am at a loss to get the computer back on line.Running win7 (32Bit) with Norton 360.
View 9 Replies View RelatedI try to export a Detailed Device Report to a CSV. It failes:
<HTML><META HTTP-EQUIV="content-type" CONTENT="text/html;charset=utf-8">
<H1>HTTP Status 500 - </H1><HR SIZE=1 noShade>
<P><B>type</B> Exception report</P><P><B>message</B> <U></U></P><P><B>description</B> <U>The server encountered an internal error () that prevented it from fulfilling this request.</U></P><P><B>exception</B>
[code].....
Exporting to PDF works OK.CW is running on Windows server. RME is 4.3.1
Just upgraded from 4.0 - to 4.2 then to 4.2.1 15. As you may have seen with periovous posts of mine its not been an esay ride.I have now managed to get it all working - backups AAA etc but for some reason i cannot get the replication to work! Its states the following...
Within the Database Replication active log - Error OutBound database replication failed - refer to CSAuth log file.Other lines in the log state its ok eg - Component logging reports was updated - being replicated to slave...
Please note that the $ is a symbol that i have used because the symbol in the log is strange and i cannot seem to be able replicate here with this text, for example $etworks - should be networks.
Network Resources - Network Devices and AAA Clients- File Operations - Add - gives me File Format Validation Faliled. I am carefull to leave the header as it is. The header in the Import Template looks faulty, see attached. When exporting devices I also get the same header as attached. I also tried to change the header so its all in one column, but with same result.
View 1 Replies View Relatedthe WLC 4404 present this logs:
*osapiReaper: Oct 02 14:55:11.152: %OSAPI-3-FILE_OPEN_FAILED: osapi_file.c:370 Failed to open the file : /proc/927/stat.(erno 24)
*osapiReaper: Oct 02 14:55:11.152: %OSAPI-3-TASK_GETTIME_FAILED: osapi_task.c:3431 Failed to retrieve statistics (/proc/<pid>/stats) for task 'gccp_t'
*osapiReaper: Oct 02 14:55:11.152: %OSAPI-3-FILE_OPEN_FAILED: osapi_file.c:370 Failed to open the file : /proc/926/stat.(erno 24)(code )
when present this loggs the device present those symptoms:
lost GUI session
Lost console conection
Lost SSH and Telnet conecction
the WLC 4404 not work is stopedd
From 6.0.199.4 to AIR-CT5500-K9-7-3-101-0.aes. Get the error below halfway through download of file to controller.
*Dec 11 14:18:55.775: %UPDATE-3-FTP_TRANSFER_FAIL: updcode.c:4158 Error FTP file Transfer [ftp_get], <28>, No space left on device.
I have no idea how to delete files form the storage on the 5508? TFTP transfer gives me this error after the upload is done:
% Error: Code file transfer failed - Error while writing output file
*Dec 11 15:11:45.514: %TFTP-3-FILE_WRITE_FAIL: tftp_client.c:517 Error while writing 512 bytes to file. Tftp error.
*Dec 11 15:11:45.514: %TFTP-3-WRITE_NOCLOSE_FAIL: tftp_client.c:147 Error while writing the local file: No space left on device
*Dec 11 15:11:45.514: %OSAPI-3-FILE_WRITENOCLOSE_FAILED: osapi_file.c:582 Failed to write 512 bytes (FileDesc:64). file write no close failed
In my head office we have Cisco 3845 router.in the router we put the show log command the below error is came..
What is the error??why the error came??
25024684: Feb 29 10:33:13.759 India: %FAN-3-FAN_FAILED: Fan 1 had a rotation error reported.
25024685: Feb 29 10:33:33.759 India: %FAN-3-FAN_FAILED: Fan 1 had a rotation error reported.
25024686: Feb 29 10:33:53.759 India: %FAN-3-FAN_FAILED: Fan 1 had a rotation error reported.
25024687: Feb 29 10:34:13.759 India: %FAN-3-FAN_FAILED: Fan 1 had a rotation error reported.
When I try to log-in to my D-Link DIR-835 Router using IE9, I get an 'Authentication Failed' error. FireFox & Chrome work just fine. what I need to change or fix in IE9 so it will also log-in to my router?
View 13 Replies View RelatedI am running IOS version 8.0(5) in cisco ASA 5520. This issue i am facing is that when the memory utilzation reaches 49 percent, the web-vpn users are not able to login as they are getting a blank page. The only error which is getting in the output " sh mem webvpn allobjects" is ERROR: Memory allocation failed?
View 2 Replies View RelatedWhile installing ISE 3395 i am getting error failed to start DB!
Database is not available withintimeout of 240 seconds.this could be reason of incorrect network configuration or lack of resources on the appliance or VM, run the folloing CLI to re-prime database 'application reset-config ise'
I had upgraded the MSE to 7.0.202. Release code. The Upgrade along with the 4 database zips went smooth.But the MSE status shows following
View 2 Replies View RelatedGetting this error on the data center 2581 (12.4(24)T) from a GRE/IPSEC tunnel, remote branch is 2811 running 12.4(25d)
%CRYPTO-4-RECVD_PKT_MAC_ERR: decrypt: mac verify failed for connection id=
The tunnel has been up and working okay for months, nothing has changed on the config and the key is correct. Traffic is following but remote users are complaining of performance issues. A wireshark shows checksum errors and lots of packet resends. Remote ISP has checked the circuit and says its clean.The data centre router has quite a few tunnels but only 1 causing this issue. From the head end router -
sh crypto ips sa | b x.x.x.x
current_peer x.x.x.xport 500 PERMIT, flags={origin_is_acl,} #pkts encaps: 15129, #pkts encrypt: 15129, #pkts digest: 15129 #pkts decaps: 13346, #pkts decrypt: 13346, #pkts verify: 13346 #pkts compressed: 0, #pkts decompressed: 0 #pkts not compressed: 0, #pkts compr. failed: 0 #pkts not decompressed: 0, #pkts decompress failed: 0 #send errors 1, #recv errors 1992
Can a VPN module go bad like this? I've tried disabling the branch onboard engine and using software but it doesn't work.
Whenever I try to goto a webpage within any browser,despite me being connected to my network(though 1 received packet to every 20 or so sent packet ratio) it tells me that DNS lookup failed. I had a similar issue on my other pc that I use more often,though connecting through WIFI momentarily resolved the issue,before I returning to wired,where everything has been fine. My other pc however has no wifi adapter. So ive been stuck.
View 12 Replies View RelatedI have have a XPS L502X. I decided to make a clean installation based on Windows 7 Ultimate.My problem is when I instal the driver for the "Dell Wireless HSPA 5540" it fails with then warning:
"Authentication failed. The .... driver cannot be installed on this computer...."
How to install driver for this ?
IPsec VPN configured between ASA5525-X and Linksys RV042 ,While transfering some exe from ASA5525-X side to Linksys RV042 side over VPN hash-sum of this file changes, so, when you open transferred file, you have an error message "File is corrupted". If you try to transfer file from Linksys side, hash-sum is ok. Also, work with oracle application is interrupted because of unknown reason. IPsec works only if using router instead of ASA.
View 2 Replies View RelatedI am unable to connect to the internet on my desktop computer. The error message I receive is" Download failed(12007) The sever name or address could not be resolved" I am running windows 7. Hooked up to att uverse. My laptop is working as you can see by sending this message. I have been trying to fix this problem for the last 2 days to no avail. I uninstalled norton hoping it was a firewall problem. On the local area connection it shows IPV4 connedtivety: No Network access.
View 2 Replies View RelatedI have just gone through hours of tech support with my ISP and still cannot seem to get online. Problem is the same as recent posts by jerguy1928, with message "DNS lookup failed...." coming up in Google Chrome. Both IE and FF just say cannot connect.Running Windows 7 on laptop. I have tried alt DNS settings (Google and others), all the CMD suggestions, disabling firewalls etc, etc! Other computer in house connects just fine.Ping works fine. Really, there appears to be no reason to not be able to connect - since I am actually connected!
View 13 Replies View RelatedDHCP Client and Network Location Awareness aren't working. When I tried to start DHCP Client, I got Windows could not start the DHCP Client service on the Local Computer.Error 5: Access is denied. I checked the dependencies and all of them were on. For Network Location Awareness, I got the error Windows could not start the Network Location Awareness on Local Computer. For more information, review the System Event Log. If this is a non-Microsoft service, contact the service cendor, and refer to service-specific error code -1073741288. One of its dependencies is fine, but I don't know how to check the other two, Ancillary Function Driver for Winsock and NetIO Legacy TDI Support Driver. Also, how do I check the event log?Everything on the list that was said to check is running expect these two the lisie was having problems with. I have not had anything with memory recently and have not been able to successfully go through a system restore. I have tried many of the suggestions and just am not sure what to do anymore. The computer works perfectly fine, minus it cannot get on the internet.
View 1 Replies View RelatedWhen I try to connect to our domain I get the error message:Changing the Primary Domain DNS name of this computer to "" failed. The name will remain "(name of our domain)" The specified domain either does not exist or could not be contacted.The procedure is the same I've used since Hector was a pup and never had a problem. I can't add users to the domain and can't log on directly to the domain.
View 1 Replies View RelatedI am using URL Snooper to copy URLs from slide share into my hard drive. Although my internet connection is working fine i am getting the message"ERROR:failed to find a suitable network driver". I cannot understand what the problem is" Please assit me in this issu
View 1 Replies View Related[code]....
Red error what is the reason? Only appears in the window 2003 server.
I use a Belkin wireless router in my home, and my teenage son just obtained a netbook running Windows CE with wifi. How can I allow temporary access to our wifi network without storing the password in his computer and allowing him to get on the web anytime he wants? We have had past issues with internet conduct and I want to be careful.
View 12 Replies View RelatedWe inserted GLC-T modules and on Nexus 5548 they are showing SFP validation Failed , as per Cisco doc GLC-T is support . Since we have 28 such modules and all after inserting showing same error. please see the below details. I also try configuring speed and inserting modules but no result ..let me know whether my GLC-T module is supported on Nexus 5548
INMUMFDS1SWCORE01# show module
Mod Ports Module-Type Model Status
--- ----- -------------------------------- ---------------------- ------------
1 32 O2 32X10GE/Modular Supervisor N5K-C5548P-SUP active *
2 16 O2 16X10GE Ethernet Module N55-M16P ok
3 0 O2 Daughter Card with L3 ASIC N55-D160L3 ok
[code]
Upon checking the logs, I'm seeing a lot of these messages:
*emWeb: Oct 25 14:11:01.345: #LOG-3-Q_IND: spam_lrad.c:10136 Validation of STAT_PAYLOAD failed - AP 00:3a:98:09:4e:d0
Always the same MAC address, which I assume is a Cisco AP trying to join. The output interpreter/message decoder isn't much useful. 5508 Controller running ver 7.3.101.0.