Wireless :: Router Will Not Recognize PrinterJan 26, 2011
Router will not recognize the printer
Router will not recognize the printer
d-lINK n-300 (DIR-615) Wireless Router HW/Ver: E1, F/W Ver: 5.00NA
I am having a problem with the DIR-615 router seeing my printer on a wired network. The printer is a Brother HL-2170W (also capable of a wireless connection). All other network PC's connect okay. I have attempted both wired and wireless connection procedures that came with the printer with no luck. The DIR-615 router does not see the printers IP address. How can I get the router to recognize the printer?
Region : Brazil
Model : TL-WR470N
Hardware version: v2 Firmware version
latest (updated yesterday)
My Iphone doesnt recognize my printer (HP Photosmart D110a) when I try to print something from it by AIRPRINT. After updated my printers and routers firmwares, the problem continues. Ive been read a lot and seems that the problem is caused by a problem with IGMP or Multitasking protocol.... But I dont find these in my routers page even after updated my firmware.
I've got a small wireless home network that currently has 2 computers - my desktop is running XP Pro, and a laptop that my wife uses running XP Home. I've recently bought a new laptop that is running Windows 7, and although it picks up the wireless feature of the network (it has wireless internet access), I can't seem to figure out how to get this new Windows 7 laptop to see the other PCs or the printer connected to my desktop. I've tried a couple of the "how-tos" online, but I must be doing something wrong. getting my Windows 7 box to see the other PCs and printer on my networkView 3 Replies View Related
recently my internet got disconnected, they reconnected my internet configured my modem when i tried to connect my router ,it would connect to my comp but it said there was no internet. I reset it to factory settings via ip address and then threw the button on the router when i installed software it keeps saying that the router cannot recognize the internet and i should contact my internet provider, but my internet is working when i connect it to the comp directly?View 4 Replies View Related
we have tried updating the firmware, restarting the modem, etc.We are looking to connect our 2 TB WD My Book to our E4200 to share amongst the network to various gaming systems and computers , When we go to storage it says "USB Device is not Supported"View 1 Replies View Related
I had a Sony 8gb usb drive plugged in and was working great with my smart tv and computer..... over last weekend i unplugged the drive and had to format it to my xbox moved what i need to and hen i formatted it back to ntfs the router wont recognize the usb drive. during this i also was facing this bad gateway error 502...i downgraded my router and now using the classic but i still get a non recognizable device error.View 1 Replies View Related
How do i enable my desktop computer to recognize my wireless router using the Ethernet portView 1 Replies View Related
E4200 does fail functionality on 2 area's:
- 1) Media Streaming Server
- 2) NAS supporting modern USB devices, which register with multiple personalities/devices in one physical USB device.
1) Is already known by Cisco and hopefully the choose to fix it properly
2) Must be known now. Multiple users are reporting this lack of support.
NAS functionality of E4200 does not work/ gives problems with:
- Toshiba StorE Alu 2S USB 3.0, 1 TB disk. PN: PA4239E-1HJ0
- Iomega eGo 1 TB USB 3.0, (black casing) , PN 31924500, RPHD-UG3
Both drives report themself with 2 devices under Windows 7: 1x USB storage decive + 1x CD readonly device?
1TB harddisk partitioned into 2, an HFS+ and an exFAT. Could the exFAT partition be the reason? But I do have an HFS+ partition and it's the 1st partition on this disk.View 1 Replies View Related
Ok this is the send router this has happened to but anyway after a power blink the router no longer recognizes that i have a modem connected to it no matter how many times I reboot both of them it can't recognize that i have a modem connected i know it is not the modem because i'm using it to type this right now directly connected to my desktop
I have windows 7
Linkysy E4200 V1
Century link DSL modem 660 series
I cannot get my Toshiba Thrive to recognize my router (wrt-1209) or the other way around. I am able to get on a neighbors non-secure network immediately. No problem with the other wi-fi connected computers on my network.View 1 Replies View Related
I wrote down the password of my wireless router on installing it. However, each time I want to add a new device to the router, the password that I wrote down does not prompt the router to recognize the new device or equipment. How do I go back into my computer and retrieve the password to my router if I did copy it down wrongly? how to retrieve the password.
I bought a Wireless-N Home Router MODEL WRT120N so that I could use my new Kindle Fire online, since I could never catch an open wi-fi signal in my house. Router IS correctly installed and working fine.....but when I go to use my Kindle, I see it on the list, click on it, enter my password.......and it tells my my password must be incorrect. I KNOW it is correct! I even went and CHANGED the password just in case!
My Kindle keeps giving the message "Unable to connect to the selected Access Point. Please check the password you have provided."
One moment the laptop was using the wireless connection from the router in our house and the next it lost internet access and then wasn't able to recognize the SSID or connection at all on the available wireless connections. We have reset the router and restarted the laptop countless times yet the only internet access we have is on the computer the router is hooked up to.The wireless connection works neither on the laptop nor the Wii, both previously works merely hours ago and with no problems until now.We assume there is an issue with the router itself, whether it be a loose ethernet cord (which only faintly can be moved in its place).It's almost as if the router is stopping them (Wii, and laptop) from having access. When we explore the wireless internet properties on the laptop, it shows the wireless connection, yet only there and doesn't give access to it. Could it be the router, or could the company have restricted WiFi only to the computer it is hooked up to?View 1 Replies View Related
How do i enable my desktop computer to recognise my wireless router using the ethernet portView 2 Replies View Related
I have a WRT54GS V7 that I have been running for a few years now with no problems until today.My wife used the internet from her laptop through the day but this evening after she moved to the bedroom and booted up the laptop, she found there was no internet connection. I tried what I know in cases like these, unplugging the router or modem for brief periods of time to try and get things going again but to no avail. So I tried using the Easylink Advisor which basically suggested the same process.
At this point, my internet connection is coming in from the cable just fine. I have access on the desktop which is wired and works with no problems. The modem and router lights are both signaling that everything is fine but no wireless internet coming from the router.
Using the desktop I tried looking for some solutions and tried resetting the router. I ultimately called customer support but being out of warranty they wanted too much although she suggested that I needed to reconfigure the router since I had reset it. I followed the online instructions for reconfiguring but still have gotten nowhere.
I am unable to get my E2000 router to recognize my Ipad2 when trying to connect.View 2 Replies View Related
Whenever I try to set up a security code for any of the settings (WEP/WPA etc), as soon as I hit save my computer does not recognize it and I get kicked off the internet and have to restart my router. I have the Linksys model number WRT160N V3View 2 Replies View Related
I have Linksys E3000 Router and it is connected to 7 Devices at this moment via DHCP. I have got New NAS Enclousre (8th Device) which has got Lan port . I have connected Box to One free Port on E3000 Router. I see DHCP Reservation from 192.168.0.1 assging one IP to My NAS Enclosure Box i.e 192.168.0.13 But when i ping that box . It's not pingable. When i try to browse that NAS Enclosure's setup web page - it's not opening. I can access that box setup page if i connect direct 1:1 Lan cable over private network (169.254.XXX). It means web server is runing on box. I am clueless. E3000 is assigning IP to NAS Enclosure but can't Browse or Ping. I tried to Assign Manual IP address to NAS enclusure and reconnect to router. Still I can't ping or browse.
#arp -a show that box has IP. (Output from MAC os) .
? (192.168.0.13) at (incomplete) on en0 ifscope [ethernet]
Ping test from Router Page.
PING 184.108.40.206 (220.127.116.11): 32 data bytes
40 bytes from 18.104.22.168: icmp_seq=0 ttl=46 time=286.6 ms
40 bytes from 22.214.171.124: icmp_seq=1 ttl=46 time=290.2 ms
Set up our E3000 following the set-up guide. However, wireless devices (laptop, iPhone) recognize the network, but cannot connect. There's no prompt for a password or anything.View 6 Replies View Related
I can't connect to the internet on my desktop pc after I reinstalled windows. I have linksys wrt320n router and I can connect to it only by wi-fi. When I try to install router's setup wizard or network magic - it writes that my computer is not connected to router though it is connected in the same way as it was before. In the LOCAL AREA CONNECTION it is also written that network cable is unplugged...I also tryed to connect just internet cable without router - PC also didn't react. Maybe the problem is that my network adapter (nvidia nforce) is without appropriate drivers? Cause I can't find drivers for nvidia nforce networking contoller for windows 7View 11 Replies View Related
My belkin router F7D4401 is not being recognize by my desktop whereas i can connect to the same without a problem using my laptop. The belkin router management software shows the router as connected when i joined it my laptop but the desktop always says not connected.View 5 Replies View Related
my computer wont recognize my router and i lost the cd, what do i doView 1 Replies View Related
My computer suddenly doesnt recognize my router.it recognizes othrer routers, and my other PC's are recognizing the router.the router is located very close to the PC, and no other electronic devices located near by.View 2 Replies View Related
My Dell destop with Windows 7 all of a sudden doesn't seem to recognize my router, yet my laptop works fine (which I'm using now). After reading other posts, I reset the router with no results, used a new cable from the Belkin to the computer, changed ports, checked connections, restarted; nothing. When I do an ipconfig, a small window pops open and goes off before I can make anything out. I undestand Belkin's IP address is 192.168.2.1 and I'm showing that my IPv4DHCP Server is that, as is my DNS server. The IPv4WINS server shows nothing.View 9 Replies View Related
I just moved into a new apartment and inherited a former roommates internet set up. Our router was infected with DNSchanger, so I sought to reset the router and update the firmware. I reset the router and it no longer recognized the internet connection. I can connect when plugged directly into the modem, but the router doesn't recognize the internet connection. Below is my ipconfig/all log:
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
Region : Belgium
Model : TL-MR3220
Hardware Version : V1
Firmware Version : 3.12.21 Build 120523 Rel.37880n
ISP : 3G mobile
My router TL-MR3420 does not connect to my 3G modem. I did all the steps according to the router configuration. Despite of that, once it is on the status it doesn�t recognize my modem, HUAWEI, model number E1820.
I have a Speedstream 4300 modem in bridge mode and a linksys WRT54G2 router set to PPPoE like I was instructed. On the status page of my router underneath the PPPoE setting it has IP, Subnet Mask, and Gateway all set to 0. The only advice I was able to obrain from my ISP was to powercycle the router and modem, which I did and no change.View 1 Replies View Related
Region : India
Model : TL-MR3020
Hardware Version : V1
Firmware Version :
ISP : aircel,idea
I bought this router just today, but it cant recognize my huawei e303c 3g modem.i've upgraded the firmware. This router supports the dongle or not?
When setting up Belkin fF5D8235-4 v2 router it will not recognize the Speedstream 4100 modem. Is there a fix for this?View 1 Replies View Related
Region : Others
Model : TL-MR3040
Firmware Version: 3.14.4 Build 121017 Rel.62268n
I have purchased TL-MR3040 especial for share my 3G account . I have connect it by ethernet port and made setups and it is in 3g/4g only mode. In system checks my modem indicated as " Identified" the modem is a Huawei E160E . My notebook and tablet connects by wireless connection to TL-MR3040 but the router does not dial ISP number *99# . The led on usb modem continues flashing. the 3G modem works perfectly with my notebook and tablet and I use the same parameters for TL-MR3040 with tablet. But most of the parameters don't exist on setup pages of TL-MR3040 . [code]
I have an IBM R-40 thinkpad that I restored to original with the IBM icon and then updated it to a service pack 3 and updated anything that popped up. Now it doesn't recognize any wireless at all. I tried the FN,F5 still no luck. It has a INTEL card, Model WM3B2100 in it and it worked fine before the restore and update.View 1 Replies View Related
Region : Argentina
Model : TL-MR3220
Hardware Version : V2
Firmware Version :
Region : Others
Model : TL-MR3220
Hardware Version : V1
Firmware Version : latest
ISP : Orange
The TL-MR3220 takes a long time to identify the 3g modem and sometimes it will not identify it at all and says "unplugged". Sometimes "unplugged" suddenly apears after the modem has been identified and was working properly.Is this the normal behavior of this device ? Why ? What can be done ? I'm Using Alcatel X500D 3g modem.
i need to add a wireless printer to the router.View 1 Replies View Related
I have a Fujitsu Lifebook Series E that used to connect to the internet but will not connect now. It will not recognize or list any wireless connections available. Actually, I can't even pull up an empty list of wireless connections available. It does have a local area connection but it says a network cable is unplugged. I know it may be a faulty wireless card but I don't know how to test it or, if it is bad, where the find it to replace it.View 14 Replies View Related
I recently had to reinstall XP and all the drivers for my friend's laptop but it seems it does not recognize any wireless connections. When I click the Choose a wireless network it says "No wireless networks were found in range" however I can use my laptop just fine.I clicked the network adapter and it says everything is running fine so I am not sure what the issue is. How to get the wireless internet working.View 2 Replies View Related
My son is at college and his roommates can connect to wireless, but his computer does not recognize a network. It says the settings saved on the computer do not match the requirements of the networkView 1 Replies View Related
I just set up my wireless security, and I get "incorrect password" message when I try to log onto my ipad.View 1 Replies View Related
I have 2 4402 WLC's and am in the process of deploying 1042 APs out to sites. But The AP's wont recognize the WLC. I have configured the DNS for CAPWAP but still no dice. I have had to serial into each unit and give it a static IP and then I can see it on the WLC. Shoulsnt this be automatic?View 21 Replies View Related
I have a new n series Belnet wireless router that can take a usb printer. I have a Lexmark 2200 Series 1 Printer (with usb connection). I have used this printer with my laptop (runs Windows xp) by connecting the printer usb directly. I have also connected my laptop to the wireless router. I have plugged the printer into the wireless router's usb port. Is it possible to access the printer this way? I do not know what I should do next. The laptop cannot access the printer through the wireless.View 5 Replies View Related
I have a wireless network in my house. The only printer in the house is connected to my home office desktop.I have an old HP DeskJet 672 as wells as my old Speed Stream wireless router that has a printer connection port in the back. How can I plug this printer into this wireless router thus making a family shared printer?View 2 Replies View Related
Just built my new system and when I installed my network card drivers and utilities, a message comes up ASUS Wireless LAN card is taken apart from your desktop PC.View 1 Replies View Related
I have a 3825 router running 12.4t IOS. I installed DSU/CSU part number HWIC-1DSU-T1 in the router and it does not recognize it. Is this the right card for this router? Is there anything I can look at to determine the issue? I think the router only has 32M RAM. Below is a show hardware. Card is still currently installed.View 2 Replies View Related
Currently my network is set up so all machines are on the same workgroup.The server (Server 2008) is also part of this workgroup and has shares set up to only allow access if a client PC is logged in as the same user/password as the server uses.I want to set up a domain on the server so I can install Exchange, but if I do this, will my Workgroup PC's lose access to the server shares?View 5 Replies View Related