I tried to configure a 2920 with a WIC=HWIC-1CE1T1-PRI. In the serial 0/0/0:23 I set the isdn switch type to primary-ni2c. When I then exit configure mode and show interface se0/0/0:23 the switch type has been changed to primary-ni. Is this normal?
View 1 RepliesI have cisco2811 and HWIC-1CE1T1-PRI in the main office are using to connect 10 branches ( 10 ISDN lines) for Data.
I have available channels in the used E1 so I can use them for voice using PVDM2-64 ?
The customer has an existing ISDN30 - 8 channels backup circuit what was originally terminated to a C2611XM Now they required to replace this old router with a new one.The old router build:
CISCO2611XM - CISCO Dual 10/100 Ethernet Router w/ Cisco IOS IP, 32F/ 128D
CAB-E1-PRI - CISCO E1- ISDN PRI Cable, 10 Feet
NM-1CE1B - CISCO ^1-Port Channelized E1/ISDN-PRI Balanced Network Module
CAB-5-XOVER-3M - COMSTOR Crossover Cable RJ45-RJ45 - 3
The new what we would provide:
1 x CISCO2911/K9 - Cisco 2911 w/3 GE,4 EHWIC,2 DSP,1 SM,256MB CF,512MB DRAM,IPB 1 1 x S29UK9-15104M - Cisco 2901-2921 IOS UNIVERSAL 1 1 x HWIC-1CE1T1-PRI - 1 port channelized T1/E1 and PRI HWIC 1 1 x CAB-ACU - AC Power Cord (UK), C13, BS 1363, 2.5m 1 1 x CAB-E1-RJ45BNC - E1 Cable RJ45 to Dual BNC (Unbalanced) 1 Included: PWR-2911-AC Cisco 2911 AC Power Supply ISR-CCP-EXP - Cisco Config Pro Express on Router Flash 1 MEM-2900-512MB-DEF - 512MB DRAM for Cisco 2901-2921 ISR (Default) 1 MEM-CF-256MB - 256MB Compact Flash for Cisco 1900, 2900, 3900 ISR 1 SL-29-IPB-K9 - IP Base License for Cisco 2901-2951 1
we bought the Cisco 1921 ISR with the HWIC-1GE-SFP to get a router that would be able to connect via fiber to our switches. I called Cisco and their reps recommended this router/HWIC pair to me.
I have got the basic configuration out of the way and I have discovered my router with CCP, now I would like to know how I can configure this HWIC. I have the SFP(GLC-SX-MM= ) installed correctly and it is connected to our test switch via an LC/LC cable, but when I do 'show ip interface" all ports are down except the one my workstation connects directly to the router with (gigabit0/1).
I've been collecting information on principles of SHDSL connection. I have found plenty of examples on how to configure only one SHDSL link. Very soon I'm going to the site to install two independent SHDSL links in Cisco 2811 which has one Cisco HWIC-2SHDSL module, so I can route one type of traffic through one connection and another type of traffic through another. Both SHDLS links have static IP addresses and probably different VPI/VCI values. how to install two SHDSL links into one HWIC-2SHDSL module, set one value for VPI/VCI on one link and another value for VPI/VCI on another link, also set one IP address on one link and another IP adddress on another link?
View 13 Replies View RelatedIs there a way to configure a 28xx series router with a HWIC-AP card as a wireless client instead of a wireless access point? There isn't a network drop in the location that I need to place a router, but there is an active Access Point that reaches the area.
View 1 Replies View RelatedI'm adding a 2nd 3com 2920-SFP switch to our network, and was wondering how to connect them up in series(?) for more available user ports. They have 4 SFP ports, and wanted to know if this was how its done.
View 1 Replies View RelatedI am trying to configure a newly installed HWIC-4ESW on a 2811 router to bridge to the FE 0/0 interface. Currently, I have a cheap switch connected to FE 0/0 which in turn connects to all the phones, however now I just want to connect all the phones to the HWIC and have it internally bridge to FE0/0 for the connectivity to CME, etc.
View 5 Replies View RelatedHaving 2 router with 2 sub interface configured with HSRP. The server sending the data have the route default gw xxx.xxx.xx.252 HSRP address. But on of the routers did got HW problem so we did shut it down, R2 with IP xxxx.xxxx.xxxx.251, problem so the traffic didn't go there correct when was using the HSRP address some packaged went there but not all of them no blocks in the logs. But then we did change the server direct to to the working router R1 xxxx.xxxx.253 everything did start working fine again. was working fine. Logs i got in the router was max tcp half-open connections.
I am wondering if something wrong in the configuration below and why the traffic didn't got there correct when using the HSRP address. Its working fine when using R1 IP address. The devices are 2 Cisco 2620 routers.
R!1
interface FastEthernet0/0.192
description Prod_Inside
encapsulation dot1Q 192
ip address xxx.xxx.xxx.253 255.255.255.192
ip access-group Inside_Outside in
ip verify unicast reverse-path
no ip redirects
[code]...
We have 1841 router with HWIC-4ESW we need to config point to point data Dual leased lines failover concept please find attached diagram.
View 3 Replies View RelatedWhat is the difference between HWIC-1ADSL-M and HWIC-1ADSL without the "-M"?Can either of the above ADSL cards be used in Cisco 3845 router? We are using HWIC-1ADSL-M in our Cisco 3845 routers everywhere?
View 1 Replies View RelatedI have an existing C2821 router (2 onboard GE + 1 HWIC-2FE) currently. Like to add another 1 HWIC-2FE. Saw this doc on Cisco website which states Max of 2 HWIC-2FE for Cisco2821. Want to confirm this is indeed so as another link states max of 1 HWIC-2FE.
View 3 Replies View RelatedI am looking for a way to use a 3G connexion on ASR1000.Is it possible to install HWIC module of ISR2 in SPA slot or use an USB modem on the RP?
View 2 Replies View RelatedI want a low cost solution router with 16 10/100 routed ports...The idea is to club 16 different segments on ofc to this router via media convertor and there will be dynamic protocols such as EIGRP or higher running between these segments.
The router needs to be security enabled...the equipments needs to be a router by defination (not a layer 3 switch)..As per my understanding there is limitation on number of HWIC-2 FE that can be put in ISR G2 series due to which I cannot reach that figure...
Kindly let me know if i can use SM-ES3-16-P in the place of HWIC-2FE for this kind of requirement.
Does the ASR-1000 accept an HWIC module, or must one go to a SIP/SPA for all modules?
View 1 Replies View Relatedif the card HWIC-1SER is the equivalent card HWIC-1T for 1861 router?
View 3 Replies View RelatedI have cisco 3845 router with 4 HWIC-2FE card none of them is detected the message displayed is [code]
View 7 Replies View RelatedI just added an HWIC-16A to a Cisco 2911 router for use as a Terminal Server.[URL]I've installed and configured the card properly. However, I receive the following error message:Attempt from Cisco CLI
View 2 Replies View RelatedI have a Cisco 2811 router with c2800nm-adventerprisek9_sna-mz.124-2.T6.bin as IOS and i wsh to install this HWIC 4port to increase available ports on my router. Wish to know if this is going to work,that is, if i installed it the IOS available will recognise this card
View 4 Replies View RelatedI have cisco router 3925 and i add install HWIC-4ESW, as i sew on cisco documents you can hot swap the hwic without reload the router but i it's not working at all. How to do it ?
View 1 Replies View RelatedI'm trying to backup my primary WAN with secondary backup connection - 3G WAN through Cellular 0/0/0.Point is that I need to track some external IP address on my primary interface, for examle 8.8.8.8. If it is not reacheable, then router brings up backup connection - 3G. This can be done by using dialer-watcher.Simple.But unfortunately my primary WAN interface is an FastEthernet, which is the coonected to a switch, switch to WAN . There is no dialer-watch commands on it. Thats sad .
One more time :
WAN -> SWITCH -> ROUTER(WITH 3G HWIC and Fa 0/0 connected to switch).
I have a scenario where multiple branches are connected to Head Office via DSL links. The branches are located in differenct exchanges, everyone once in a while ALL branches go down at the exact same time except 3 branches and those 3 branches don't have ATM interface on the router, rather they have external DSL modem, all other branches that face the disconnection (for couple of minutes) have either HWIC-1ADSL-M or HWIC-2SHDSL and the DSL line is directly plugged into the card. [code]
I tried so many solutions like adding "operating-mode auto" command under the subinterface, IOS upgrade, changed dynamic routing protocol from EIGRP to OSPF... Nothing worked, on the logs of the router it just shows "EIGRP neighbor down", at the time of the problem I can't ping any of the affected branches on their WAN ATM interface although it stays physically "up up".Could the problem be a missing command that I need to add under the subinterface? Something maybe related to clocking or timeout or..?Note that hte problem occurs randomly, every few days, sometimes every 10 days, and all branches with ATM interface go down at the exact same time.
I' ve come across an weird ospf issue between my router connected via layer 2 service provider link, details as below.We have a base station router for satelite termination at service provider end connected via Layer 2 vlan link to a head end C3945, current interface for head end is a layer 2 vlan and layer 3 ip address lives under sub interface, config as below
-Head End router
-Cisco 33945
i have some issue with Hwic-4ESW, if i install one card(Hwich-4ESW) is working all port then i install one more card ( Hwic-4ESW) it not working.interface and vlan is up but from my PC to port Hwic-4esw not working. what is problem on this ?
View 9 Replies View RelatedIn our Environmet we have 3845 Edge Router Current Ios Version is Version 12.4(1a),(c3845-advipservicesk9-mz.124-1a.bin)As management got another fiber leased line(Single Mode) for which i have install SFP slot part number HWIC-1GE-SFP,after installation of HWIC-1GE-SFP in router the follwing slot is showing
GigabitEthernet0/1/0
%HWIC_1GE_SFP-6-SFP_IN: Interface GigabitEthernet0/1/0 1000BaseLX SFP has been inserted
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/1/0 xx.xx.xx.xx. YES manual up down
for testing purpose i tried the same procedure into the switch and its working fine where as in Router the link is not coming up ,
According to specifications fo Cisco ISR G2 2911, it has got 4 EHWIC slots. But in [URL] appears that Cisco2911 supports only 2 HWIC-2FE or only 2 EHWIC-1GE-SFP-CU.
View 1 Replies View RelatedI am trying to configure multiple dsl-groups on a HWIC-4SDHSL-E module and the option does not exist. According to the Cisco documentation I should be able to do this, but I only get pairs as an option.
1921(config-controller)#dsl-group ? pairs Link number <cr>
[URL]
This is what I am trying to do which I have done before on the 1841.
dsl-group 0 pairs 0, 1
shdsl annex A-B
shdsl rate 4096
[Code].....
is there any known issue in configuring multilink ppp using an old WIC-1T and a newer HWIC-1T on the same Cisco 1841 router ?
View 2 Replies View RelatedI have a CISCO 1841 with a HWIC interface to my ISP. I want to make a ADSL connection and my current running-file is: [code] The problem I have is that the ISP connection is established but then goes down.
View 1 Replies View RelatedI was looking an HWIC card for CISCO2901-SEC/K9. We have one internet connection (ADSL) current.Now we want to backup internet connection from cable service provider. I will implement IPSec on this HWIC.
What HWIC cards can I choose for this router?
I have got 3845/3945, I would like to increase HWIC slot density for HWIC 4 PORT ISDN BRI S/T ports through the NM/NME/NMX slots, Is there any measns to do that?
View 2 Replies View RelatedI have Cisco 2801 router with IP Base image, i have upgraded its image into advance Ip services for using IP SLA features but after upgradation HWIC card not showing in configuration.
When i recall IP base image then configuration show presence of HWIC card but with advance IP services HWIC card not showing.
We have configured new 2911 router with HWIC-2T with it.However we are seeing serial interfaces up, but can hardly ping other end. Again we are seeing a lot of CRC errors on serial interface.
But if we connected same cable, with other old router 2811, it works fine. Confiuration is same on both the routers. [code]